Owner's Manual
Table Of Contents
- Handbook
- Factory default reset
- Safety Guidelines
- Welcome
- Contents
- Before You Begin
- Trademark Acknowledgments
- Rear Panel Connections and Controls
- Audio/Video Connections
- Connection Guide
- Radio & Wireless Audio Connectors
- Other Connectors
- Speakers
- Connecting Speakers
- Operation
- Extended front panel menu
- Front Panel Operation
- Remote Control
- Device Mode/Source keys
- Customising the Remote
- Essential Setup
- Auto Speaker Setup
- Setup Menus
- Connecting to a Network
- Decoding Modes
- Tuner Operation
- Troubleshooting
- Specifications
- Device Code Tables
- Custom Installation Notes
- Contents
- Introduction
- Set-up
- Conventions
- Serial Cable Specification
- Example command and response sequence
- System Command Specifications
- Input Command Specifications
- Output Command Specifications
- Menu Command Specifications
- Setup Adjustment Command Specifications
- Treble Equalisation (0x35)
- Bass Equalisation (0x36)
- Room Equalisation (0x37)
- Dolby Volume (0x38)
- Dolby Leveller (0x39)
- Dolby Volume Calibration Offset (0x3A)
- Balance (0x3B)
- Subwoofer Trim (0x3F)
- Lipsync Delay (0x40)
- Compression (0x41)
- Request incoming video parameters (0x42)
- Request incoming audio format (0x43)
- Request incoming audio sample rate (0x44)
- Set/Request Sub Stereo Trim (0x45)
- Set/Request Zone 1 OSD on/off (0x4E)
- Set/Request Video Output Switching (0x4F)
- Set/request input name (0x20)
- FM Scan up/down (0x23)
- DAB Scan (0x24)
- Heartbeat (0x25)
- Reboot (0x26)
- Bluetooth status (0x50)
- Setup (0x27)
- Room EQ name(s) (0x34)
- Now Playing Information (0x64)
- Input config (0x28)
- General Setup (0x29)
- Speaker Types (0x2A)
- Speaker Distances (0x2B)
- Speaker Levels (0x2C)
- Video Inputs (0x2D)
- HDMI settings (0x2E)
- Zone settings (0x2F)
- Network (0x30)
- Bluetooth (0x32)
- Engineering menu (0x33)
- AV RC5 command codes
- Product Info
- Mandatory Software Update
- Software Release Notes
- Warranty & Product Registration
34
HDMI settings (0x2E)
Set / request HDMI settings menu info.
COMMAND:
Byte: Description:
St 0x21
Zn 0x01
Cc 0x2
Dl 0x01 / 0x0A
Data1
Data 1-09
0xF0 - request HDMI config
set HDMI config as below
Et 0x0D
RESPONSE:
Byte: Description:
St 0x21
Zn Zone Number
Cc 0x2E
Ac Answer code
Dl 0x0A
Data1
Data2
Data3
Data4
Data5
Data6
Data7
Data8
Data9
Data10
Zone 1 OSD
0x00 - Off
0x01 - On
Zone 1 Out
0x00 - Out 1 & 2
0x01 - Out 1
0x02 - Out 2
Zone 1 lip sync (information only)
0x00 - 0xFA lipsync in 1mS steps
HDMI Audio to TV
0x00 - Off
0x01 - On
HDMI Bypass & IP
0x00 - Off
0x01 - HDMI & IP On
HDMI Bypass source
0x00 - Last
0x01 - STB
0x02 - Game
0x03 - AV
0x04 - SAT
0x05 - BD
0x06 - VCR
0x07 - PVR
CEC Control
0x00 - Off
0x01 - Output1
ARC Control
0x00 - Off
0x01 - Auto
TV Audio
0x00 - Off
0x01 - Auto
Power Off Control
0x00 - Off
0x01 - Auto
Et 0x0D
Video Inputs (0x2D)
Set / request speaker level menu info.
COMMAND:
Byte: Description:
St 0x21
Zn 0x01
Cc 0x2D
Dl 0x01 / 0x06
Data1
Data 1-16
0xF0 - request Video Inputs config
set Video Inputs as below
Et 0x0D
RESPONSE:
Byte: Description:
St 0x21
Zn Zone Number
Cc 0x2D
Ac Answer code
Dl 0x06
Data1-6 Video input in order for:
Data1-CD, Data2-Aux, Data3-FM, Data4-DAB, Data5-NET, Data6-BT
0x00 - STB
0x01 - GAME
0x02 - AV
0x03 - SAT
0x04 - BD
0x05 - VCR
0x06 - PVR
0x07 - None
Et 0x0D