Owner's Manual
Table Of Contents
- Handbook
- Factory default reset
- Safety Guidelines
- Welcome
- Contents
- Before You Begin
- Trademark Acknowledgments
- Rear Panel Connections and Controls
- Audio/Video Connections
- Connection Guide
- Radio & Wireless Audio Connectors
- Other Connectors
- Speakers
- Connecting Speakers
- Operation
- Extended front panel menu
- Front Panel Operation
- Remote Control
- Device Mode/Source keys
- Customising the Remote
- Essential Setup
- Auto Speaker Setup
- Setup Menus
- Connecting to a Network
- Decoding Modes
- Tuner Operation
- Troubleshooting
- Specifications
- Device Code Tables
- Custom Installation Notes
- Contents
- Introduction
- Set-up
- Conventions
- Serial Cable Specification
- Example command and response sequence
- System Command Specifications
- Input Command Specifications
- Output Command Specifications
- Menu Command Specifications
- Setup Adjustment Command Specifications
- Treble Equalisation (0x35)
- Bass Equalisation (0x36)
- Room Equalisation (0x37)
- Dolby Volume (0x38)
- Dolby Leveller (0x39)
- Dolby Volume Calibration Offset (0x3A)
- Balance (0x3B)
- Subwoofer Trim (0x3F)
- Lipsync Delay (0x40)
- Compression (0x41)
- Request incoming video parameters (0x42)
- Request incoming audio format (0x43)
- Request incoming audio sample rate (0x44)
- Set/Request Sub Stereo Trim (0x45)
- Set/Request Zone 1 OSD on/off (0x4E)
- Set/Request Video Output Switching (0x4F)
- Set/request input name (0x20)
- FM Scan up/down (0x23)
- DAB Scan (0x24)
- Heartbeat (0x25)
- Reboot (0x26)
- Bluetooth status (0x50)
- Setup (0x27)
- Room EQ name(s) (0x34)
- Now Playing Information (0x64)
- Input config (0x28)
- General Setup (0x29)
- Speaker Types (0x2A)
- Speaker Distances (0x2B)
- Speaker Levels (0x2C)
- Video Inputs (0x2D)
- HDMI settings (0x2E)
- Zone settings (0x2F)
- Network (0x30)
- Bluetooth (0x32)
- Engineering menu (0x33)
- AV RC5 command codes
- Product Info
- Mandatory Software Update
- Software Release Notes
- Warranty & Product Registration
To update via USB (recommended):
The USB stick should
be
empty and freshly formatted
Unzip the file
AVR
_ l v22_0v472.zip &
put
the unzipped file AVRx0_systeml v22.fw onto a memory stick (so it is the only
file on the stick)
Turn on the A
VR
& wait until fully started (approx. 30 seconds for network module to fully start).
Insert the stick into the USB socket on the rear
of
the AVR.
Simultaneously press INFO & DISPLAY on the front panel until the front display shows
UPDATE
...
(it will alert that there
is
no network file)
Wait for the USB stick to be searched
Wait around 20 minutes, do
NOT
power
off
during this time.
Once the Update has finished perform a Factory Reset*
Put the unzipped file image.swu onto a memory stick (so it is the only file on the stick)
If
not already, turn on the A
VR
& wait until fully started (from power
on
wait at least 30 seconds for the network module to
fully start)
Simultaneously press INFO & DISPLAY on the front panel until the front display shows
UPDATE
...
Wait for the USB stick to be searched
Wait around 20 minutes, do
NOT
power
off
during this time.
Once the Update has finished perform a second Factory Reset*
To update via the internet:
Use a browser and navigate to the IP address
of
the unit (located in
Menu
> Network > IP Address)
On the Main Page, check "Device version"
if
this shows "0.100.4
72"
then skip to
"To
update the main
unit..."
If
the Device version is
not
"0
.100 .4 72", then click "Device Settings"
Click
"Check
for update"
setup Main
Pag
~ Device
;.;~:
y
~~=rk:.:ngs
Goog
le
Cast
Webdlent
settings
Device
Name
ARCAM
AVR20-44aNC
s-.
AlrPlay
Password
Armware
Update
I
Check!;
update I
Reboot
device
to
the
Update
Mode
-
Accept the update - this will take around 20 minutes.
To update the main unit, press and hold the menu key on the unit for five seconds to enter the engineering menu.
Select
"Check
for Update".
Ifan
update
of
the main unit is available, the update will begin.
Wait around 90 minutes, do
NOT
power
off
during this time.
The A
VR
will restart after completing the upgrade.
Once the Update has fmished perform a Factory Reset*
To check your software version, press INFO &
DIRECT
simultaneously, the front display will show:
MCUVer
lv22/09
*The unit
MUST
be restored to factory defaults and any setup changes made again after an update.
To
do this, press and
hold the
MENU
key on the unit for approximately 5 seconds (until the front panel display shows the engineering menu),
release the
MENU
key, then press OK, then press DIRECT. The unit should then
power
cycle to standby.
Due to the
EEPROM
contents changing between software versions, restoring settings from a secure backup
is
NOT
recommended.
-1-