Operation Manual
E-9E-8
English
P49
connections
Note
Please read the ‘Placing the unit’, ‘Power’ and
‘Interconnect cables’ sections on page5 before
connecting up your P49 power amplier!
ST/BRIDGE/DM
MODE
XLR/RCA
INPUT
25dB/31dB
GAIN
L
R
PRE
IN
PRE
OUT
R
4–16 OHMS. CLASS 2 WIRING
SPEAKER 1 SPEAKER 2
L
4–16 OHMS. CLASS 2 WIRING
SPEAKER 2 SPEAKER 1
PRE IN R PRE IN L
110-120V/220-240V
~ 50-60 Hz
350W MAX
POWER INLET
SUPPLY
VOLTAGE
SWITCH POSITIONS
115 = 110 - 120V~
230 = 220 - 240V~
TRIGGER IN
TRIGGER OUT
Voltage select
Ensure that the voltage selected
matches your local power supply.
Power inlet
Connect the correct
mains cable here.
Unbalanced
pre-amplier inputs
Use these sockets to connect
your pre amplier if it has
unbalanced phono outputs.
Trigger input
TRIGGER IN allows the P49 to be remotely
turned on and put into standby by an
external source, the C49 for example.
Speaker terminals
e P49 is equipped with two
pairs of speaker terminals. See
pages 15 - 18 for information
on connecting loudspeakers.
Input switches
ese switches allow the P49
to be congured in dierent
modes depending on the
system into which it will
be installed and the type of
speaker connection topology
that is used. See pages 16 –
18 for switch positions and
connecting loudspeakers.
Pre-amplier output
PRE OUT provides a copy of
the signal applied to the
PRE IN sockets. Please note
that this is a passive output,
no additional ltering or
amplication is applied.
Balanced XLR
pre-amplier inputs
Use these sockets to connect your
pre amplier if it has balanced XLR
outputs.
Note
Please ensure your P49 is turned o before altering
any of the input switches!
Trigger output
TRIGGER OUT allows the P49 to control the
power state of any connected equipment,
such as a P49/P349 power amplier. In
normal use there is no need to make any
connections to these outputs.
P349
connections
Note
Please read the ‘Placing the unit’, ‘Power’ and
‘Interconnect cables’ sections on page5 before
connecting up your P349 power amplier!
XLR/RCA
INPUT
PRE IN
PRE OUT
4–16 OHMS. CLASS 2 WIRING
SPEAKER 1 SPEAKER 2
4–16 OHMS. CLASS 2 WIRING
SPEAKER 2SPEAKER 1
PRE IN 1 PRE IN 3
110-120V/220-240V
~ 50-60 Hz
350W MAX
POWER INLET
TRIGGER IN
TRIGGER OUT
1 2
4–16 OHMS. CLASS 2 WIRING
SPEAKER 1 SPEAKER 2
1
CHANNEL
3
PRE IN 2
2 3
SUPPLY
VOLTAGE
SWITCH POSITIONS
115 = 110 - 120V~
230 = 220 - 240V~
Voltage select
Ensure that the voltage selected
matches your local power supply.
Power inlet
Connect the correct
mains cable here.
Unbalanced
pre-amplier inputs
Use these sockets to connect
your pre amplier if it has
unbalanced phono outputs.
Trigger input
TRIGGER IN allows the P349 to be remotely
turned on and put into standby by an
external source, the C49 for example.
Speaker terminals
e P349 is equipped with three pairs of
speaker terminals. See pages 15 - 18 for
information on connecting loudspeakers.
Input switches
is switch selects between
the unbalanced (RCA) and
balanced (XLR) inputs.
Pre-amplier output
PRE OUT provides a copy of
the signal applied to the
PRE IN sockets. Please note
that this is a passive output,
no additional ltering or
amplication is applied.
Balanced XLR
pre-amplier inputs
Use these sockets to connect your
pre amplier if it has balanced XLR
outputs.
Note
Please ensure your P349 is
turned o before altering
any of the input switches!
Trigger output
TRIGGER OUT allows the P349 to control
the power state of any connected
equipment, such as a P49/P349 power
amplier. In normal use there is no need
to make any connections to these outputs.