- A & R Cambridge AVR Surround Amplifier Handbook

ManualsBrandsArcam ManualsAmplifierFMJ AVR600

AVR600

HANDBOOK AVR surround amplier

 













English

Summary of content (68 pages)

PAGE 1
English AVR600 Handbook AVR surround amplifier ��
PAGE 2
safety guidelines �� CAUTION: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. Class II product This equipment is a Class II or double insulated electrical appliance.
PAGE 3
consignes de sécurité �� ATTENTION : afin de réduire les risques de choc électrique, n’ouvrez pas le boîtier de l’appareil. Les pièces internes ne sont pas réparables par l’utilisateur. Pour tout problème matériel, contactez des techniciens qualifiés. ATTENTION : afin de réduire les risques de choc électrique et d’incendie, veillez à ne pas exposer cet appareil à la pluie ou à l’humidité.
PAGE 4
F-2
PAGE 5
safety guidelines........................................E-2 welcome.......................................................E-3 before you begin…...................................E-4 rear panel connectors...............................E-7 audio/video connections.........................E-8 Connection guide................................................. E-12 radio connectors..................................... E-14 other connectors..................................... E-16 speakers.......................
PAGE 6
before you begin… as well as two digital outputs for digital recording of digitised audio sources. DVD-Audio and SACD can be connected via the multi-channel input. Control of the AVR600 is either by front panel control buttons, IR remote control or RS232 port. The AVR600 is a high-quality and high-performance home-cinema processor and amplifier built to Arcam’s quality design and manufacturing standards.
PAGE 7
< Place the unit on a level, firm surface, avoiding direct sunlight and sources of heat or damp. < Do not place the AVR600 on top of a power amplifier or other source of heat. < Do not place the amplifier in an enclosed space such as a bookcase or closed cabinet unless there is good provision for ventilation. The AVR600 will run warm during normal operation. < Do not place any other component or item on top of the amplifier as this may obstruct airflow around the heat-sink, causing the amplifier to run hot.
PAGE 8
Trademark acknowledgements Arcam is a registered trademark of A & R Cambridge Ltd. Dolby Volume Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Dolby True HD, Digital, Digital Plus, PL IIx Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories. DTS-HD Master Audio Manufactured under license under U.S.
PAGE 9
Audio connectors Two-channel and multichannel, see page 10. � �� HDMI For information, see page 8.
PAGE 10
audio/video connections Before connecting your AVR600 to your source components and speakers, please read through the next few pages which will explain all the input and output connectivity that is available. The ‘Speakers’ section explains how to connect up your speakers to avoid damage to the amplifier and how to arrange your speakers for best performance. �� AV, SAT, DVD, VCR, PVR Connect the HDMI video outputs of your source equipment to these corresponding HDMI inputs.
PAGE 11
� Z3 OUT Connect these analogue audio outputs to your Zone 3 equipment. See ‘Multi-room Setup’ on page 48 for information. �� Zone 2 connectors Z2 AUDIO OUT, Z2 VIDEO OUT Connect these analogue audio and video outputs to your Zone 2 equipment. See ‘Multiroom Setup’ on page 48 for information.
PAGE 12
�� Phono �� This input can be connected directly to a record deck which has a direct output from a moving magnet (MM) cartridge. MCH input This multi-channel analogue audio input can be connected to �� a source device which outputs �� surround sound on its analogue outputs. Such devices typically �� include DVD-Audio and SACD �� players.
PAGE 13
E-11 English
PAGE 14
Connection guide DVD player �� The preferred audio hook-up is using the coaxial digital connector (usually marked Digital audio out), in addition to the coaxial analogue outputs for left and right channels.
PAGE 15
More information is given in the rDock quick start guide (or rLead quick start guide) supplied with these accessory units.
PAGE 16
(where fitted) In strong signal areas, the DAB ‘T’ ribbon aerial supplied can be used with reasonable results. Mount the aerial as high up as possible on a wall. radio connectors �� DAB �� In the UK the ‘T’‑elements need to be positioned vertically for DAB �� reception since broadcasts are vertically polarised. In �� other localities, check with �� your Arcam dealer or try �� both horizontal and vertical positions for best �� reception.
PAGE 17
English FM AM �� In strong signal areas, the FM ribbon aerial supplied can be used with reasonable results. Mount this as high up as possible on a wall with the top of the ‘T’‑elements positioned �� vertically or horizontally, depending on the reception in your area.
PAGE 18
rLead/rDock �� For use with an Arcam rLead or rDock accessory. See page 13 and the accessory documentation for details. �� Use with control devices having an RS232 serial port (for example, Crestron and AMX touch screen controllers). This connection is also used for upgrading the AVR600’s internal software. Networking is a large subject and only the briefest guidelines are presented in this handbook.
PAGE 19
English Trigger connectors �� The trigger connectors (Trig Z1, Trig Z2 and Trig Z3) provide an electrical signal whenever the AVR600 is switched on and the relevant zone enabled. �� The trigger signal can be used to switch on and off compatible pieces of home entertainment equipment, for example, you could set up a trigger to turn on your television and DVD player whenever the AVR600 was switched on.
PAGE 20
speakers The AVR600 allows you to connect up to seven speakers and three active subwoofers in the main system. The output channels correspond to speakers installed in the front left, centre, front right, surround left, surround right, surround back left, surround back right and an active subwoofer.
PAGE 21
Subwoofer A subwoofer will greatly improve the bass performance of your system. This is useful for reproducing special cinema effects, especially where a dedicated LFE (Low Frequency Effects) channel is available, as with many discs encoded with Dolby or DTS technologies. More than one subwoofer unit may be required for larger installations, particularly in rooms of a timber frame construction.
PAGE 22
operation Operating your AVR600 Selecting a source For information display we recommend you use the OSD (On-Screen Display) on your display device whenever possible. To select a particular source, press the –input or input + buttons until that source is shown on the front panel display, or (if available) press the corresponding source button on the remote. The following sources are available: Switching on Press the front panel power button in.
PAGE 23
Extended front panel menu Updating firmware using a PC Zone 2 provides the option for the occupants of the master bedroom, conservatory, kitchen, etc. to view or listen to a different source at a different volume level from the main zone (Zone 1).
PAGE 24
Direct Stereo Direct on/off. Provides a direct analogue path from the analogue inputs to the left and right front outputs. Switches off any surround processing modes and shuts down the DSP circuits for best stereo sound quality. Mode front panel operation Selects between Stereo and the available surround modes for the current source. Display Info This switches the display brightness between off/dim/bright. Selects the information displayed on the lower left portion of the front panel.
PAGE 25
The CR102 universal remote controller The CR102 is a sophisticated ‘universal’ backlit remote control that can control up to eight devices. It is preprogrammed for use with the AVR600 and many other Arcam products (FM/DAB tuners, CD players and DVD players). With its extensive built-in library of codes, it can also be used with thousands of third party audio-visual components – TVs, satellite and set-top boxes, PVRs, CD players, etc. See the list of codes at the back of this handbook, beginning on page 58.
PAGE 26
Useful information Backlight A blue backlight comes on for five seconds whenever a key is pressed. This helps you use the handset in subdued lighting conditions. It may be possible to hear a quiet tone being emitted from the remote control when the backlight is on. This is perfectly normal. Power LED blinks Short blinks indicate a valid key press. Multiple short blinks convey information (such as a device code) or signal the beginning and successful completion of a programming sequence.
PAGE 27
Method 1 (Direct code setup) This section describes the simplest (preferred) way to program the CR102’s Device Mode keys to control the non-Arcam devices in your system. �� < Some of the modes are locked to Arcam operation but can be unlocked if required (see page 52). < A mode only controls Arcam equipment.
PAGE 28
�� AMP Device Mode P The A Device Mode button configures the CR102 to control the AVR600. Pressing this button does not affect the currently selected input on the AVR600. IMPORTANT: The CR102 must also be in AMP Device Mode to control the following sources: PHONO, MCH (multi-channel analogue), AUX, NET (optional network audio), USB, IPOD (for use with the optional Arcam rLead or rDock).
PAGE 29
The AVR600 Network client is selected by pressing S + e in AMP Device Mode on the CR102. When using the network client, the keys below are used to navigate music files in AMP Device Mode. Navigate the files and menus on the screen.
PAGE 30
�� SAT Device Mode �� The z Device Mode button configures the CR102 to control the functions of a satellite receiver. You will need to configure this Device Mode to work with your equipment. Pressing this button also selects SAT as the AVR600 source. P Toggles power between standby and on 0…9 Functions as original remote number key. Selects Tape input on the AVR600.
PAGE 31
�� PVR Device Mode The v Device Mode button configures the CR102 to control the functions of a video recorder or similar device. You will need to configure this Device Mode to work with your equipment. Pressing this button also selects PVR as the AVR600 source. P 0…9 PHONO E TV/AV r S AUX H & Toggles pause of playback Functions as original remote number key. ( Fast forward Selects Tape input on AVR600. ! Operates the Favourites function if the PVR uses this feature.
PAGE 32
�� CD Device Mode The c Device Mode button configures the CR102 to control the CD functions of Arcam CD players, although this can be changed (see page 25). Pressing this button also selects CD as the AVR600 source. P 0…9 PHONO E RPT r S AUX H NET e �� Toggles power between standby and on. Functions as original remote number key. Decrease (–) and increase (+) AVR600 - + volume. ) Fast rewind $ Play AVR600. & Toggles pause of playback Toggles random (‘shuffle’) play on and off.
PAGE 33
E-31 English
PAGE 34
essential setup Speaker types Before you use your AVR600 it is essential that you enter some information into the Setup menus about your speaker configuration. This allows the AVR600 to process any surround sound digital source to exactly match your system and give you the ultimate surround sound experience.
PAGE 35
When activated, a calibration tone is played through each channel of the AVR600 in turn, including the subwoofer channel. The calibration tone cycles round each of the speakers twice. If you do not have a full 7.1 speaker configuration there will be periods of silence between some speaker channels. Follow the ‘progress’ information on-screen.
PAGE 36
setup menus The Setup menus allow you to configure all aspects of your AVR600. The next few pages will go through the menu items and explain their function. The Setup menus will probably look quite daunting if you are new to setting up home cinema, but the majority of them need only be configured once when you first install the system (or if your system changes or you move house!) Menu panel Adjustment panel The left-hand panel lists the setup screens available for adjustment.
PAGE 37
The audio and video settings on this page of the Setup menu can be tailored specifically and independently to the currently selected input. When a different input is selected on the Input line, all the input-specific settings for that input are displayed below it. These settings are applied to the named Input only and are stored in memory and recalled each time the unit is powered up and whenever that input is selected. Input – The currently selected input connectors to which the settings below relate.
PAGE 38
Sub Stereo – If Left/Right+Sub or Sat+Sub is selected in Stereo Mode above, this setting adjusts the level of the subwoofer when the source is two channel stereo. You should typically select RGB+Sync if you are using a standard SCART to 4-wire phono breakout cable to connect an RGB SCART source. General Setup completely over to one channel. This function resets to equal left/right balance when the input is changed. Brightness – Sets the video brightness for this input.
PAGE 39
Audio In iPod – If you have an iPod connected to the AVR600 using an Arcam rDock or rLead, this control allows you to set which audio input is used. Auto Setup Auto Speaker Setup of your loudspeakers and subwoofer (if present) is controlled by this menu. A full description of how Auto Speaker Setup works is given on page 33. Remember to insert the calibration microphone into the AUX input on the front panel and position the microphone at the listening position before running Auto Setup.
PAGE 40
Video Inputs Video Outputs Settings to optionally assign a video source to each of the normally audio-only inputs. The settings in this menu control the output resolution from the video processor in the AVR600 as well as the operation of the two HDMI outputs. These settings are stored in memory and recalled each time the unit is powered up.
PAGE 41
Out 1 & 2 Frame Rate – This setting controls the output frame rate when both HDMI outputs are used simultaneously. This setting is only valid if Output Switching is set to Output 1 & 2. < The dropdown list shows all the frame rates that the AVR600 video processor can output. Frame rates that are not supported by the connected display devices at the above resolution are greyed out and cannot be selected.
PAGE 42
decoding modes Introduction Two-channel source modes Your AVR600 receiver provides all the key decoding and processing modes for analogue and digital signals, including the latest high definition audio formats over HDMI. The following decoding and surround modes are available for standard and high definition Dolby Digital 2.0, DTS 2.
PAGE 43
Digital multi-channel source material is normally provided as ‘5.1 audio’. The ‘5.1 channels’ comprise of: left, centre and right front speakers, two surround speakers and a low frequency effects (LFE) channel. Since the LFE channel is not a full range channel, it is referred to as ‘.1’. Surround systems decode and reproduce the 5.1 channels directly. Dolby Digital EX and DTS-ES matrix enhanced decoding systems create one extra rear channel from information buried in the two surround signals of the 5.
PAGE 44
Dolby volume Dolby Volume is a sophisticated new technology that resolves the problem of different volume levels between programme content (e.g. a TV show and advert breaks) and between sources (e.g. a rock radio station and DVD, or between two TV stations). It lets the listener enjoy everything at the same preferred listening level without having to reach for the volume control to compensate for the different recording/output levels. This is the Volume Leveller function of Dolby Volume.
PAGE 45
E-43 English
PAGE 46
tuner operation The AVR600 is fitted with an internal AM/FM tuner. Depending on your location, it may also be fitted with a DAB tuner (Europe) or Sirius satellite radio connection (Americas). Sirius requires the purchase of the ‘SiriusConnect™ Home Tuner’ kit and Sirius subscription – please visit www.sirius.com for details. This section deals with tuner operation, for information on setting up the tuner and installing aerials, see page 14.
PAGE 47
Operation In addition to the channel and preset selection, previously mentioned, you can also cycle through the station categories (Rock, Pop, Country, etc.) using the ] and [ keys. The first station in each category is displayed. You can then scroll through other stations in that particular category using the D or E buttons on the CR102 remote. On the OSD a star (‘ * ”) is shown before the category name to show you are scrolling through stations only in the current category.
PAGE 48
�� network/usb operation �� The AVR600 is fitted with a network audio client which is capable of playing internet radio stations as well as stored music on a network storage device such as a PC, or from a USB flash drive. For information on installing the AVR600 on your network, see page 16.
PAGE 49
English external amplifiers Analogue pre-amplifier outputs All pre-amplifier analogue outputs are buffered, have a low output impedance and are at line level. They are able to drive long cables or several inputs in parallel if required. � �� R, L, C Connect these to the equivalent (Right, Left and Centre) front channels of your power amplifier. �� SW1 Main subwoofer output.
PAGE 50
The connection guide on the following page shows how the AVR600 is normally connected in a multi-room installation. The Z2 Out, R and L phono sockets should be connected to the analogue audio inputs (Usually labelled Analogue Audio in) of the Zone 2 display device, or to the inputs of an additional stereo power amplifier in Zone 2 (for example, the Arcam P38). Zone 2 receives only signals obtained by the AVR600 from the analogue audio, Composite and S-Video inputs.
PAGE 51
Zone 1 Zone 3 �� E-49 ��
PAGE 52
Code Learning customising the CR102 The CR102 comes with a complete library of preprogrammed codes. After you have set up the CR102 for your device, you may find that there are one or more functions on your original remote which do not have a place on the CR102 keypad. For convenience, the CR102 offers a Code Learning feature that allows you to copy up to 16 functions from an original remote control onto the CR102 keypad.
PAGE 53
You can program your CR102 to issue a sequence of commands when you press a single key. Any sequence of commands you regularly use can be reduced to a single key press for your convenience. For example, you might want to turn off your TV, VCR and Satellite at the same time. < A key programmed with a Macro is available in all modes; it will replace that key’s different functions for all modes. < A Macro can consist of up to eight key presses. Example: To deassign the Macro associated with the h key 1.
PAGE 54
Copy a key between Device Modes It is possible to copy functions between Device Modes. However, remember that button functions are Device Mode specific and therefore effectively ‘punch-through’ to the original Device Mode when copied over. The following example copies the AVR600 Direct function from the CR102 AMP device mode to the shifted function of the # button on AV Device Mode. 1. Press and hold S until the power LED blinks twice: * *. 2. Press 9 9 4. 3.
PAGE 55
The Mode key IR punch-through default is ‘on’. Example: To set the Mode key IR punchthrough to AMP Device codes Command summary Direct code setup Key mover (e.g. AV mode, NNNN=code number) (e.g. SAT mode, DISP key to MENU key) a S * * NNNN * * P zS**994DU Library search Mode mover (e.g. AV mode) (e.g. change SAT to TV(AV)) a S 9 9 1 * * P [ until unit turns off S to save S**992az Code blink back (e.g. restore SAT) a S 9 9 0 ** 1 count blinks for first N S**992zz 1.
PAGE 56
Problem There are no lights on the unit Check that... < the power cord is plugged into the AVR600 and the mains socket it is plugged into is switched on. trouble shooting < the power button is pressed in. If a red LED is present, the AVR600 is in standby mode. Press any button on the front panel or remote control. The unit responds erratically or not at all to the remote control < there are fresh batteries in the remote control.
PAGE 57
Sound only comes from some of the speakers Check that... < you have an appropriate surround source selected and playing. < the DVD disc is encoded in the appropriate format, and the correct format < < < < < < Unable to select Dolby Digital or DTS decoding modes Problem has been selected in the disc start menu of the DVD player (if applicable). the DVD player has been set to output ‘bitstream’ audio on the digital output.
PAGE 58
specifications Continuous power output (20Hz—20kHz at 0.05% THD), per channel 2 channels driven 150W All channels driven 120W THD at full rated power <0.2% Residual noise & hum <0.
PAGE 59
Worldwide Guarantee English product guarantee This entitles you to have the unit repaired free of charge, during the first two years after purchase, at any authorised Arcam distributor provided that it was originally purchased from an authorised Arcam dealer or distributor. This is extended by a further three years (five years total) on the return of your product registration card.
PAGE 60
Bang & Olufsen BaoHuaShi Baosheng Barco Basic Line device code tables Bastide Bauer Baur Bazin Beaumark Beijing Beko Anam TV 888 A.R.
PAGE 61
Harwood 0067 0586 Hauppauge Havermy HCM 0039 0517 0067 0123 0039 0247 Hedzon 0586 helios 0895 Hema 0247 Hifivox 0139 Higashi 0246 Highline 0294 Hinari 0039 0586 0517 Hisawa 0485 HISense 1393 0538 1238 Hitachi 0193 0039 0138 0247 0529 0586 0774 1200 0542 1179 Hitachi Fujian 0138 Hitsu 0039 Höher 0744 Home Electronics 0636 Hongmei 0039 Hongyan 0294 Hornyphon 0067 Hoshai 0485 Hua Tun 0039 Huafa 0039 Huanghaimei 0039 Huanghe 0039 Huanglong 0039 Huangshan 0039 Huanyu 0246 Huaqiang 0294 Huari 0294 Hugoson 0920
PAGE 62
TV (cont.
PAGE 63
Combitech Condor Craig Crown VCR Accent Admiral Adventura Adyson Aiko Aim Aiwa 0102 0078 0030 0102 0308 0308 0030 0067 0062 Akai 0067 0672 0378 Akashi 0102 Akiba 0102 Akura 0102 Alba 0308 0030 0111 Allorgan 0270 Allstar 0111 America Action 0308 Amstrad 0030 Anam 0067 0308 Anitech 0102 Ansonic 0030 Aristona 0111 ASA 0067 Asha 0270 Asuka 0102 0030 Audiosonic 0308 Audiovox 0067 AVP 0382 AWA 0067 0073 Baird 0136 0030 Basic Line 0308 Beaumark 0270 Beko 0134 Bell & Howell 0134 Bestar 0308 Black Diamond 0672 Bla
PAGE 64
CBL ADB 1260 Amstrad 1252 Auna 1299 Austar 0306 Canal Plus 0473 Comcrypt 0473 Comtec 0049 Contec 0049 Daeryung 0507 Fastweb 1660 Filmnet 0473 Foxtel 1252 France Telecom 0847 freebox 1512 Funai 0049 General 0306 Instrument Jerrold 0306 Macab 0847 Madritel 1260 MNet 0473 Motorola 0306 Multichoice 0049 Nokia 1599 Noos 0847 NTL 1090 Oak 0049 Ono 1098 Optus 0306 Pace 1098 Philips 0847 Sagem 0847 Samsung 1696 Scientific Atlanta 0507 Tele+1 0473 Telepiu 0473 Telewest 1098 Telsey 1660 Thomson 1764 Trans PX 0306 UPC
PAGE 65
Bush 0743 1725 0747 0848 1466 1170 C-Tech 0798 Cambridge Audio 1139 Campomatic 1081 Digital CAT 0819 Celestial 0702 cello 1760 Centrex 0702 Centrum 0743 1035 CGV 0800 Cinea 0871 Cineral 0760 Cinetec 0743 CineVision 0899 Classic 0760 Clatronic 0818 0702 Clayton 0743 Coby 0808 1195 Codex 1263 Conia 0702 0865 Contel 0818 Continental 0902 Edison Craig 0861 Crown 0800 Crypto 1258 Cybercom 0861 CyberHome 0744 Cytron 0746 0861 D-Vision 1145 Daenyx 0902 Daewoo 0800 1513 1466 Dalton 1066 Dansai 0800 Dantax 0753 Day
PAGE 66
PVR @sat 1330 @Sky 1364 Amstrad 1205 Arnion 1330 ASCI 1364 Astro 1130 Aurora 1463 Austar 1206 B@ytronic 1442 Brainwave 1244 British Sky 1205 Broadcasting BSkyB 1205 Bush 1675 CanalSatellite 1369 Chess 1364 CityCom 1206 Comag 1442 DigiFusion 1675 DigiQuest 1330 Dream Multimedia1267 eMTech 1244 Foxtel 1206 1386 Galaxis 1206 GbSAT 1244 Gecco 1442 General Satellite 1206 Globo 1364 1442 Hanseatic 1130 HB 1244 HDT 1189 Hirschmann 1442 Homecast 1244 Humax 1206 1457 1705 Hyundai 1189 ID Digital 1206 Imperial 1130 1
PAGE 67
Smart Soniq Sony SR Star Sat Starland Stream Strong Sunny Sunny Sound Sunsat Sunstar Supermax Systec Tarbs TBoston Teac Tecatel TechniSat Technomate Technosat Technosonic Technotrend Technowelt Techsan Techwood tekComm Tele System Tele System Electronic TeleClub Telecom Telestar Televes Televisa Telewire Tevion Thomson Tiny Tioko Tokai Tonna Topfield TPS Triax Trio TT-micro Turnsat Twinner UEC Unimax Unisat United Universum Van Hunen Variosat 1303 1143 1443 1597 0877 0883 0162 0162 0743 1878 0155 1656 08
PAGE 68
SH215E Issue 2 A&R Cambridge Ltd, Pembroke Avenue, Waterbeach, CAMBRIDGE CB25 9QR, England P/N: 4301-7333+0