Progressive scan DVD player DV27 Lecteur de DVD à balayage progressif DV27 DVD-Spieler mit progressiver Abtastung DV27
This handbook has been designed to give you all the information you need to install, connect, set up and use the Arcam FMJ DV27. The remote control handset supplied with the equipment is also described. CONTENTS Welcome to the DV27 DVD player .......................................... 3 It may be that the DV27 has been installed and set up as part of your Hi-Fi installation by a qualified Arcam dealer.
Safety guidelines CAUTION ATTENTION RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR We do not advise the use of furniture cleaning sprays or polishes as they can cause indelible white marks if the unit is subsequently wiped with a damp cloth. 9. Power sources CAUTION:To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel.
Installation REMOTE IN Pb/B PROGRESSIVE VIDEO VIDEO OUT SUPPLY VOLTAGE SCART A/V OUT COMPOSITE COMPONENT Y S VIDEO G DIGITAL OUT OPTICAL 230V POWER INLET Y/G English Pr/R Pb B COAX Pr R L AUDIO OUT R PCM/BITSTREAM 1 2 RGB OUTPUT POSITIONING THE UNIT RGB output is available on both the SCART and Component/RGB sockets and offers picture quality equal to component video. Place the DV27 on a level, firm surface and ensure that there is adequate ventilation for the unit.
CONNECTING TO A POWER SUPPLY CONNECTING DIGITAL AUDIO If you have an external surround sound decoder, receiver or D-A converter that you wish to use with the DVD player, then you will need to connect it using either a coax or optical lead. These digital outputs provide 2-channel PCM, Dolby Digital, DTS or MPEG multi-channel audio, depending on the source material. It is also possible to set the digital output to always output 2-channel PCM (stereo mix-down) using the setup menu.
INTRODUCTION OPERATIONAL SETUP Congratulations – if you have followed the installation instructions then the required connections to other equipment will have been made. It is now essential to go through an initial set up procedure to ensure the DVD player is configured correctly for use. Operation 1/4 OSD Language DVD Menu Subtitle Audio Remote type OSD Status Priority SWITCHING THE POWER ON English English English English CR-134 On Not applicable Press in the POWER button on the front panel.
REMOTE TYPE TV SYSTEM This informs the player which type of remote control you are using, so that the player can take into account the slight differences between the remote types. For ARCAM remote controls, the remote type is always written on the front of the remote control, normally at the bottom of the unit. This is set at the factory to be appropriate for the type of TV used in your country. Should you need to change this setting, the options are explained below.
AUDIO SETUP ACCESS SETTING Password Rating Bitstream/2 Ch. Max 48K Not applicable Normal This section allows you to configure the type of analogue and digital audio outputs. In particular, the digital output type needs to be set correctly if you are using an external audio decoder, receiver or D-A converter. –––– View all films PASSWORD The password setting works in conjunction with the rating setting (the next menu item) to provide a means of limiting content playback by children (parental control).
COMPLETING THE SET-UP Complete the setup procedure by pressing SETUP on the remote control.This saves all the data and closes the setup menu.You can press SETUP at any time while in a menu to quit from it. To return to the setup menu at any time, ensure that there is no disc playing and press the SETUP button.
Basic use of your DVD player English DV27 DVD PLAYER Motion Adaptive Progressive Scan LOAD PLAY STOP PAUSE POWER FAST PLAY INTRODUCTION Press or on the front panel or remote control to play fast forward or backwards. For DVDs, VCDs and CDs the following speeds for fast playback are available: x2, x4, x8, x20, x60 and x100. Press the button repeatedly to cycle through the different speeds. To resume normal playback speed, press PLAY.
Using the remote control CD/DVD 0–9 keypad Ensure that DVD mode is selected using the CD/DVD toggle button. The ‘DVD’ LED above the CD/DVD button is lit briefly when DVD mode is selected. This allows direct access to individual tracks on audio CDs. To select a track, press the corresponding keypad button followed by OK. For tracks greater than 9, enter the digits in sequence. For example, to play track 15, press 1, then 5, then OK. DISP (display) Standby Dims or turns the DV27’s display on or off.
MEM (memorise) It is possible to ‘bookmark’ up to three points on a DVD title, so you can quickly jump to those parts of the title again. Press MEM to access the ‘Bookmark’ menu. SUBT (subtitle) TITLE Press SUBT on the remote control to cycle through the available subtitle languages, including ‘OFF’. Some discs force subtitles on, over-riding player set up. Press TITLE to access the DVD’s ‘Title’ menu. Note that this feature only applies to multi-title discs.
Advanced DVD and VCD features This section explains the more sophisticated DVD and VCD features, such as special playback modes. The operations described here are not exactly the same for DVDs and VCDs, but are similar enough to make it appropriate to group them together. SPECIAL PLAYBACK MODES Playback modes are available that allow repeat, shuffle and programmed playback. Note that many VCDs have a single track, so some operations involving tracks will not be relevant.
VCD TO PROGRAM A SPECIAL SEQUENCE Press PROG on the remote control to open the ‘Programme’ menu. Note that playback must be stopped first. You can enter a sequence of up to 20 tracks for programmed playback. If you enter data that is invalid for the current disc, the field is erased automatically. DVD The bottom of the screen shows the number of titles present on the disc, together with the number of chapters in the title selected currently (or the first title if no title has yet been specified).
Advanced MP3/WMA/JPEG and audio CD features The DV27 DVD player has the ability to handle MP3, WMA and JPEG files, when these are burned on to a CD-R or CD-RW disc. Picture/ Photo CDs are also playable. These file types may be mixed together, if desired. This section explains the more sophisticated CD-based features, for audio CDs and for CD-ROM discs containing MP3, WMA and JPEG files.
When you have entered the programme to your satisfaction, press the PROG button again. This changes the display to show the programmed list (‘Playlist’ mode) and playback starts automatically. Playback can be stopped and started using the STOP and PLAY keys, as normal. To stop the programmed sequence and return to normal playback, press the PROG button for a third time; this stops playback and changes the player to ‘Browse’ mode.
Reference: Troubleshooting PROBLEMS WITH REMOTE CONTROLS Problem Possible cause Solution Remote control not working DVD not selected Select DVD using the remote’s CD/DVD toggle switch Batteries not installed, incorrectly installed, or flat Check battery compartment and reinstall batteries if necessary Obstruction between IR lens and remote control Remove any obstruction Player does not respond consistently to the remote control The player is not configured to use the correct remote type Change t
Problem Possible cause Solution No sound! Incorrect input selected on audio device (decoder, receiver, amplifier, etc.
Technical specifications General Power Requirements 115V or 230V AC, set by voltage selector switch on rear panel Power consumption < 45 VA Dimensions 430mm x 90mm x 280mm Weight net: 6.2kg; packed: 7.8kg Video outputs Composite video 1 x gold plated phono: 1V pk-pk into 75Ω S-Video 1 x 4-pin mini-DIN: Y 1V pk-pk in 75Ω, C 0.3V pk-pk into 75Ω Component video 3 gold plated phono sockets: Y 1V pk-pk into 75Ω; Pb 0.7V pk-pk into 75Ω; Pr 0.7V pk-pk into 75Ω. SCART socket with RGB video All 0.
WORLDWIDE GUARANTEE For further details contact Arcam at: This entitles you to have the unit repaired free of charge, during the first two years after purchase, at any authorised Arcam distributor provided that it was originally purchased from an authorised Arcam dealer or distributor.