Product Manual

ManualsBrandsArcan ManualsHydraulic Presses20-Ton Hydraulic Shop Press

SHOP PRESS

ASSEMBLY INSTRUCTIONS

CP12 - 12 TON MANUAL SHOP PRESS

CP20 - 20 TON MANUAL SHOP PRESS

CP301 - 20 TON MANUAL SHOP PRESS WITH PNEUMATIC/ HYDRAULIC POWER UNIT

P.O. Box 58 Travelers Rest, SC 29690 Phone: (800) 879-7316 Fax: (864) 834-0073

Arcan Model No. A B C D E F G

CP12 61.5" 20" 26" 8.75" 5" .75" Y(2)

CP20 64.5" 24.5" 26" 11.25" 5.125" 1" Y(2)

CP301 66.5" 24" 24" 11.25" 6.5" 1" Y (2)

A - Total Height

B - Inside Width

C - Press Feet Length

D - Bed Width

E - Stroke (ram travel distance from fully retracted position to fully extended position)

F - Pin Diameter

G - Press Plates Included

PRESS SPECIFICATIONS

Summary of content (8 pages)

PAGE 1
SHOP PRESS ASSEMBLY INSTRUCTIONS CP12 - 12 TON MANUAL SHOP PRESS CP20 - 20 TON MANUAL SHOP PRESS CP301 - 20 TON MANUAL SHOP PRESS WITH PNEUMATIC/ HYDRAULIC POWER UNIT PRESS SPECIFICATIONS Arcan Model No. A B C D E F G CP12 61.5" 20" 26" 8.75" 5" .75" Y(2) CP20 64.5" 24.5" 26" 11.25" 5.125" 1" Y(2) CP301 66.5" 24" 24" 11.25" 6.
PAGE 2
SAFETY INFORMATION WARNING This symbol alerts you to the possibility of serious injury or death if instructions are not followed. CAUTION This symbol alerts you to the possibility of damage to or destruction of equipment if instructions are not followed. Failure to heed these warnings may result in loss of load, damage to the press and/or failure resulting in property damage, personal or fatal injury. This operating manual contains important details concerning the safe operation of this tool.
PAGE 3
PARTS LIST ESTIMATED ASSEMBLY TIME: 30 MINUTES Power Unit - 1 (CP12 & CP20 ONLY) Press Frame - 1 CP12 - 12 Ton Power Unit CP20 - 20 Ton Power Unit Pneumatic Power Unit - 1 (CP301 ONLY) Press Bed - 1 CP301 - 20 Ton Pneumatic Power Unit Pump Handle & Extension - 1 Press Feet - 2 Z Bar - 1 ACCESSORIES 2" Punch - 1 Accessory only Not needed for assembly 1/2"-13 x 1-1/2" Hex Head Bolts - 4 Bearing Shield - 1 Accessory only Not needed for assembly 1/2" Nuts - 4 Press Plates - 2 Accessory only Not needed f
PAGE 4
ASSEMBLY INSTRUCTIONS 1 2 Note: In the upright position, inner bracing should form an inverted "v" with the narrower space facing the top of the press. WARNING Be aware of jagged edges on frame. Not all welds are smooth. Press bed can pinch or crush ﬁngers. Wear safety gloves. Stand frame upside down Slide bed onto frame Slide bed down to bottom of frame 3 Inside of frame WARNING Leg ends and press feet are sharp and potentially dangerous. Wear safety gloves and safety goggles.
PAGE 5
ASSEMBLY INSTRUCTIONS CONTINUED 4 Use bolts, washers and nuts to attach Z Bar to both sides of the press. Cross-section of press Note: Check all bolts for tightness. If press rocks, or is not level, loosen press feet slightly to compensate and retighten. Front view Front view 5 WARNING Bed must be at the BOTTOM of the frame before proceeding to the next step. Note: When sliding bed to frame bottom, DO NOT use bed handles.
PAGE 6
ASSEMBLY INSTRUCTIONS CONTINUED 6 WARNING Pins must be COMPLETELY through BOTH SIDES of frame. 1 Stand unit upright Slide bed above holes and hold in place 2 Secure pins underneath bed, one at a time PROCEDURE FOR BLEEDING AIR 7 1. Align power unit with "V" in top plate (opening in "V" faces the front side of the press). 2. Insert punch into receptacle UNDER bottom plate. 4. Open the release valve by rotating the handle counterclockwise ONE full turn. 3. Tighten screw to secure punch.
PAGE 7
PUMP INSTRUCTIONS FOR CP12 & CP20 1. Place the handle on the release valve and rotate clockwise until the valve is closed (hand tighten only). 2. Place the pump handle in the cradle. Move pump handle up and down to lower the carriage and apply force to the item being pressed. 3. To release pressure, remove the pump handle from the cradle and use the handle to slowly turn the release valve counterclockwise. The power unit cylinder will retract and the press cradle will return to the stored position.
PAGE 8
REPLACEMENT PARTS LIST CP12 - 12 TON MANUAL SHOP PRESS CP20 - 20 TON MANUAL SHOP PRESS CP301 - 20 TON SHOP PRESS WITH PNEUMATIC/ HYDRAULIC POWER UNIT 4 5 1 6 7 10 8 2 9 3 3 11 ITEM NO. 1 ARCAN PART NO. QTY. ITEM NO. ARCAN PART NO. DESCRIPTION QTY.