Datasheet
Table Of Contents
- RP2040 Datasheet
- Colophon
- Chapter 1. Introduction
- Chapter 2. System Description
- 2.1. Bus Fabric
- 2.2. Address Map
- 2.3. Processor subsystem
- 2.4. Cortex-M0+
- 2.5. DMA
- 2.6. Memory
- 2.7. Boot Sequence
- 2.8. Bootrom
- 2.9. Power Supplies
- 2.10. Core Supply Regulator
- 2.11. Power Control
- 2.12. Chip-Level Reset
- 2.13. Power-On State Machine
- 2.14. Subsystem Resets
- 2.15. Clocks
- 2.16. Crystal Oscillator (XOSC)
- 2.17. Ring Oscillator (ROSC)
- 2.18. PLL
- 2.19. GPIO
- 2.20. Sysinfo
- 2.21. Syscfg
- 2.22. TBMAN
- Chapter 3. PIO
- Chapter 4. Peripherals
- 4.1. USB
- 4.2. UART
- 4.3. I2C
- 4.3.1. Features
- 4.3.2. IP Configuration
- 4.3.3. I2C Overview
- 4.3.4. I2C Terminology
- 4.3.5. I2C Behaviour
- 4.3.6. I2C Protocols
- 4.3.7. Tx FIFO Management and START, STOP and RESTART Generation
- 4.3.8. Multiple Master Arbitration
- 4.3.9. Clock Synchronization
- 4.3.10. Operation Modes
- 4.3.11. Spike Suppression
- 4.3.12. Fast Mode Plus Operation
- 4.3.13. Bus Clear Feature
- 4.3.14. IC_CLK Frequency Configuration
- 4.3.15. DMA Controller Interface
- 4.3.16. Operation of Interrupt Registers
- 4.3.17. List of Registers
- 4.4. SPI
- 4.5. PWM
- 4.6. Timer
- 4.7. Watchdog
- 4.8. RTC
- 4.9. ADC and Temperature Sensor
- 4.10. SSI
- 4.10.1. Overview
- 4.10.2. Features
- 4.10.3. IP Modifications
- 4.10.4. Clock Ratios
- 4.10.5. Transmit and Receive FIFO Buffers
- 4.10.6. 32-Bit Frame Size Support
- 4.10.7. SSI Interrupts
- 4.10.8. Transfer Modes
- 4.10.9. Operation Modes
- 4.10.10. Partner Connection Interfaces
- 4.10.11. DMA Controller Interface
- 4.10.12. APB Interface
- 4.10.13. List of Registers
- Chapter 5. Electrical and Mechanical
- Appendix A: Register Field Types
- Appendix B: Errata
- Appendix C: Documentation Release History
Bits Name Description Type Reset
1 HFNMIENA Controls the use of the MPU for HardFaults and NMIs.
Setting this bit when ENABLE is clear results in
UNPREDICTABLE behaviour.
When the MPU is enabled:
0 = MPU is disabled during HardFault and NMI handlers,
regardless of the value of the ENABLE bit.
1 = the MPU is enabled during HardFault and NMI
handlers.
RW 0x0
0 ENABLE Enables the MPU. If the MPU is disabled, privileged and
unprivileged accesses use the default memory map.
0 = MPU disabled.
1 = MPU enabled.
RW 0x0
M0PLUS: MPU_RNR Register
Offset: 0xed98
Description
Use the MPU Region Number Register to select the region currently accessed by MPU_RBAR and MPU_RASR.
Table 115. MPU_RNR
Register
Bits Name Description Type Reset
31:4 Reserved. - - -
3:0 REGION Indicates the MPU region referenced by the MPU_RBAR
and MPU_RASR registers.
The MPU supports 8 memory regions, so the permitted
values of this field are 0-7.
RW 0x0
M0PLUS: MPU_RBAR Register
Offset: 0xed9c
Description
Read the MPU Region Base Address Register to determine the base address of the region identified by MPU_RNR.
Write to update the base address of said region or that of a specified region, with whose number MPU_RNR will also
be updated.
Table 116. MPU_RBAR
Register
Bits Name Description Type Reset
31:8 ADDR Base address of the region. RW 0x000000
7:5 Reserved. - - -
RP2040 Datasheet
2.4. Cortex-M0+ 90