Arecont Vision MegaDome® 2 Installation Manual 0|P a g e
Arecont Vision MegaDome® 2 Installation Manual ® MegaDome 2 Installation Manual Inside the box: Mounting the Camera: ® A. B. C. Arecont Vision MegaDome 2 camera Mounting template Rubber gasket (preinstall on bottom of camera) D. AC & DC power cable E. I/O cable F. Installation manual G. CD with AV100 software and user manuals (License Key Required for Recording) H. Pack of four (4) wood screws and four (4) dry wall anchors I. Security L-Key J. One double-sided hex key K.
Arecont Vision MegaDome® 2 Installation Manual side conduit and connect it to its respective connector inside the camera (Image 3). 4. If you are using the side conduit opening, remove the conduit plug by first removing the socket set screw using the provided doublesided hex key (Image 3). NOTE: Make sure that your installation of wires complies with Electrical Code of the local government where the camera is installed and that no bare wires are exposed. HOLE Image 3 5.
Arecont Vision MegaDome® 2 Installation Manual Adjusting the Tilt, Pan, Z-Axis (yaw): 9. To adjust the tilt, use a #1 Phillips screwdriver to loosen the screw on the side of the plastic lens bracket 1/4 turn (Image 5). CAUTION: Do not remove the screw! 10. Adjust lens tilt as required and tighten the screw. 11. To adjust the pan, use a #2 Phillips screwdriver to loosen the screw as shown in Image 5. Z-Axis (Yaw) CAUTION: Do not remove the screw. 12. Adjust the pan as required and tighten the screw.
Arecont Vision MegaDome® 2 Installation Manual IR LEDs Securing the Vandal Dome Cover: 15. Remove the protective film from the camera dome. NOTE: Be careful not to scratch the vandal dome cover. 16. Adjust black liner position to avoid blocking IR light (if applicable) or the lens as shown in Image 6-1 and 6-2. 17. Secure the vandal dome cover to the camera using the provided security L-Key. Image 6-2 Black Liner Camera Installation: 18.
Arecont Vision MegaDome® 2 Installation Manual 20. Select “Run” next to “Setup Cameras” from the AV100 application manager as shown in Image 9 and wait for “Arecont Vision Camera Installer” window to appear as shown in Image 10. 22. Select “Install Cameras” on Arecont Vision Camera Installer as shown in Image 10. 23. Confirm all cameras connected to the network switch appear in the upper window. 24. Repeat Step 22 if all of the cameras do not appear in the upper window. Image 9 21.
Arecont Vision MegaDome® 2 Installation Manual Adjusting the Remote Focus and Zoom: 27. 28. To adjust focus or zoom, open the camera web interface and click the “Focus” tab as shown in image 12. If the image is slightly of out of focus, choose “Fast Focusing” to fine tune and quickly get a precise focus position to save time. 31. To manually focus, click the “+20”, “+5”, “+1”, “-20”, “-5”, “-1” buttons to fine tune the focus.
Arecont Vision MegaDome® 2 Installation Manual Important Note How to correctly install MegaDome® 2 on a ROUGH surface wall Correct Installation: Please install the MegaDome® 2 with wall mount, (MD-WMT2) and junction box adapter (SV-JBA) to avoid water leakage risk on ROUGH surface wall surface as shown in Image 14.
Arecont Vision MegaDome® 2 Installation Manual ® MegaDome 2 Accessory (Sold Separately) Wall Mount (MD-WMT2) Installation Instructions Caution: MD-WMT2 only fits with SV-JBA and SV-EBA but not with the older MD-JBA and MD-EBA! Inside the box: A. B. C. D. E. F. Wall mount Top shield Mounting template One double-sided hex key Pack of four (4) machine screws Pack of four (4) wood screws and four (4) dry wall anchors Image 17 2. Using the mounting template, prepare the mounting surface. 3.
Arecont Vision MegaDome® 2 Installation Manual ® MegaDome 2 Accessory (Sold Separately) Junction Box Adapter (SV-JBA) for MD-WMT2 Installation Instruction Caution: SV-JBA should always be used in conjunction with a wall mount, MD-WMT2, for outdoor installation. SV-JBA will only fit with the MD-WMT2 wall mount. It does not fit the camera dome or older wall mount MD-CMT! Inside the box: A. B. C. D. E.
Arecont Vision MegaDome® 2 Installation Manual ® MegaDome 2 Accessory (Sold Separately) Pendant Mount (MD-CMT) Installation Instructions Inside the box: A. B. C. D. E. F. Top shield Pendant Mount Mounting template Pack of four (4) small machine screws Pack of four (4) machine screws Pack of four (4) wood screws and four (4) dry wall anchors G. One double-sided hex key H. Small square rubber gasket I. Large round rubber gasket Image 21 Not included but needed: J. 2.
Arecont Vision MegaDome® 2 Installation Manual ® MegaDome 2 Accessory (Sold Separately) Wall Mount Cap (MD-CAP) Installation Instructions Inside the box: A. B. Wall Mount Cap (MD-CAP) Pack of four (4) machine screws MD-CAP Not included but needed: • • • • 1½” NPT pipe nipple 1½” NPT coupling 1½” NPT flange #2 Phillips head screwdriver 1 ½” Coupling 1 ½” Pipe 1 ½” Flange A B Image 24 3. Run the Ethernet cable and outside power cable (if necessary) through the pendant. Image 23 1.
Arecont Vision MegaDome® 2 Installation Manual ® MegaDome 2 Accessory (Sold Separately) Flush Mount Adapter (MD-FMA) Installation Instructions Inside the box: A. B. C. D. white trim ring Flush mount adapter Mounting template Pack of four (4) machine screws and one (1) eyelet 5. Tighten the “lever screws” until the flush mount adapter is snuggly installed, as shown in Image 26. The “Support Arm” will ride down the screw to compress the mounting surface. NOTE: Do not over-torque the lever screws. 6.
Arecont Vision MegaDome® 2 Installation Manual ® MegaDome 2 Accessory (Sold Separately) Electrical Box Adapter (SV-EBA) Installation Instructions Caution: 3. Attach electrical box adapter to electrical box. SV-EBA fits with MD-WMT2 but not fit with ® MegaDome 2 and MD-CMT! Inside the box: (Accessory Sold Separately) A. B.
Arecont Vision MegaDome® 2 Installation Manual ® MegaDome 2 Accessory (Sold Separately) Pole Mount Adapter (MD-PMA) Installation Instructions Inside the box: A. B. C. D. E. Pole mount adapter 2x compression fittings 2x small steel straps 2x large steel straps Pack of four (4) machine screws 4. Run the Ethernet cable and outside power cable (if necessary) through the compression ® fittings and MegaDome wall mount, MDWMT2. 5.
Arecont Vision MegaDome® 2 Installation Manual ® MegaDome 2 Accessory (Sold Separately) Corner Mount Adapter (MD-CRMA) Installation Instructions Inside the box: A. B. C. D. Corner mount adapter 2x compression fittings Pack of four (4) machine screws 2x Packs of four (4) wood screws and four (4) dry wall anchors 3. Attach wall mount adapter to corner mount adapter and attach the wall mount cap as shown in Image 36.
Arecont Vision MegaDome® 2 Installation Manual Heater Kit MD2-HK Installation Instructions (Accessory Sold Separately, except –H Models) Inside the box: A. B. C. With the heater element protruding out of the camera, align the two (2) holes on the heater board with the two holes on gimbal base shown in Image 37. 4. Screw the heater board with the standoff on gimbal base as shown in Image 38. Heater Two (2) plastic stand-offs Two (2) screws Not included but needed: • 3.
Arecont Vision MegaDome® 2 Installation Manual ® MegaDome 2 I/O Cable Connection Inside the box: A. I/O Cable A I/O Connector Image 39 Not included but needed: • 1. Flat head screwdriver Image 40 ® To use the I/O ports of the MegaDome , run the I/O cable through the hole in the bottom of the camera and plug it into the connector as shown in Image 40. NOTE: The connection is a little stiff so be sure to apply enough pressure to connect it; using a flat head screw driver to push it in is recommended.
Arecont Vision MegaDome® 2 Installation Manual ® MegaDome 2 Audio Cable Connection (-A Models only) 2. Inside the box: A. Three (3) 3.5mm mono in-line jacks Connect a mono analog microphone to MICIN (Microphone In), connect the line-in signal to LINEIN (Line In), connect an active speaker with a built-in amplifier to LOUT (Line Out) via the in-line jack as shown in Image 43, if needed. Microphone Image 41 Not included but needed: B. C.
Arecont Vision MegaDome® 2 Installation Manual 19 | P a g e
