Instructions for Use

ManualsBrandsAres Models ManualsBeginner RC AirplaneSPAD S.XIII Ultra-Micro RTF

QUICK-START GUIDE

Full manual available to download from: www.Ares-RC.comFull manual available to download from: www.Ares-RC.com

Product specications are subject to change without notice.

Due to ongoing development, the actual product may vary from

images shown.

This product contains chemicals known to the State of California

to cause cancer, birth defects and other reproductive harm.

This product is not a toy! (14+) Recommended for ages 14 and

up. Adult supervision required for ages under 18 years old.

Contains small parts, keep out of reach of children 3 years of

age and younger.

To download the full Owner’s Manual &

Technical Information Guide, please visit

www.Ares-RC.com or scan the QR code with

your smart phone.

Distributed in the

UK by:

J Perkins Distribution Ltd,

Lenham,

Kent, UK

ME17 2DL.

www.jperkins.com

Distributed in Australia by:

Model Engines (Aust.) Pty. Ltd.,

PO BOX 828,

Noble Park 3174,

Australia.

www.modelengines.com.au

Ph (03) 8793 5555

warranties@modelengines.com.au

Distributed in the US by:

Firelands Customer Service/Product Support

1133 Libra Drive, Lincoln, NE 68512

www.relandsgroup.com

1-800-205-6773

customerservice@relandsgroup.com

Part Number:

AZSA3200 SPAD S.XIII Ultra-Micro RTF

AZSA3200M1 SPAD S.XIII Ultra-Micro RTF Mode 1

AZSA3201 SPAD S.XIII Ultra-Micro PTF

Quick-Start Guide (RTF & PTF)

MADE IN CHINA

Summary of content (8 pages)

PAGE 1
Quick-Start Guide (RTF & PTF) Product specifications are subject to change without notice. Due to ongoing development, the actual product may vary from images shown. This product contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Part Number: AZSA3200 SPAD S.XIII Ultra-Micro RTF AZSA3200M1 SPAD S.XIII Ultra-Micro RTF Mode 1 AZSA3201 SPAD S.XIII Ultra-Micro PTF This product is not a toy! (14+) Recommended for ages 14 and up.
PAGE 2
QUICK-START GUIDE RTF This first half of the Quick Start Guide is written for the RTF (Ready to Fly) version of the SPAD S.XIII. A full instruction manual is available to download from www.ares-rc.com. 1 Carefully remove the transit tape and the foam retainers, then gently lift your SPAD S.XIII and the other components from the box. Ensure you have the following parts: • • • • 100% Factory assembled SPAD S.XIII 4-channel transmitter with integral 100mA charger 70mAh 3.
PAGE 3
5 A fully discharged battery will be charged in under an hour, at which point the yellow light will stop glowing. The battery is now ready to use and can be disconnected from the charge lead. 6 Pull the throttle stick back to its lowest point and switch ON the transmitter. 7 Remove the magnetic battery hatch cover from the underside of the model. Connect the lead to the battery (making sure to align the red dots as before) and use the magnet retainer to clip the battery in position.
PAGE 4
QUICK-START GUIDE MODE 2 Transmitter shown Throttle Trim Buttons LED charge indicator Power indicator LED Elevator trim button Throttle/Rudder stick Elevator/Aileron stick (The Spad’s rudder is controlled by the aileron stick) Rudder trim buttons (used only for transmitter programming) Aileron trim buttons ON/OFF switch Hinged cover for flight battery charge cord 9 With the model in front of you, facing away, move the aileron stick to the left and check that the rudder moves left in response.
PAGE 5
12 13 Check that the elevator and rudder are centered and adjust as necessary using the transmitter’s trim buttons. Your SPAD S.XIII is now ready to fly. Choose a flat-calm day for the first flight or use a suitable indoor venue (a sports hall is ideal) that’s free of obstructions. Note that it’s not necessary to fly the SPAD at full throttle, indeed scale flight and extended duration are performed at much lower throttle settings. We hope you have many enjoyable flights with with your model.
PAGE 6
QUICK-START GUIDE PTF This half of the Quick Start Guide is written for the PTF (Pair to Fly) version of the SPAD S.XIII. A full instruction manual is available to download from www.ares-rc.com. 1 Carefully remove the transit tape and the foam retainers, gently lift the components from the box and ensure you have the following: • 100% Factory assembled SPAD S.XIII • 70mAh 3.
PAGE 7
5 With the model in front of you, facing away, move the aileron rudder stick to the left and check that the rudder moves left in response. Right aileron stick will move the rudder to the right. Mode 2 Transmitter Shown 6 Pull the elevator stick back and check that the elevator moves in an upward direction. Push the elevator stick forward and check that the elevator moves in a downward direction.
PAGE 8
PARTS LIST AZS1509 Motor with Pinion Gear AZS1511 Gearbox with Shaft AZS1512 Propeller Shaft with Gear AZSB1803 70mAh 1-Cell / 1S 3.