EN CERAMIC ELECTRIC FIREPLACE OPERATING INSTRUCTIONS Read the instructions carefully before operating the appliance or carrying out maintenance operations. Observe all the safety instructions; failure to observe the instructions may lead to accidents and/or damage. Store these instructions in a safe place for future reference.
GENERAL SAFETY INFORMATION Use this fireplace only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock or injury to persons. Ensure that the mains power complies with the electrical requirements of the fireplace (220-240V~/50Hz).
Keep flammable materials, such as furniture, cushions, blankets, paper, cloths, curtains and suchlike at least 1 m from the front and sides. Disconnect the mains power when the appliance is not in use or during cleaning. Do not use the fireplace in dusty environments or in the presence of flammable vapours (e.g. in workshops or garages). Do not place anything on the product; do not hang wet garments on the fireplace. Use the fireplace in a well-ventilated area.
WARNING: AVOID COVERING THE FIREPLACE TO PREVENT IT FROM OVERHEATING. The symbol below signals this warning: The fireplace may cause the risk of fire if, during operation, it is covered or comes into contact with flammable material including curtains, drapery, blankets, etc. KEEP THE FIREPLACE AWAY FROM THESE MATERIALS. Do not connect the fireplace to the power supply until it has been correctly assembled or positioned. Do not run the cord under carpets.
DESCRIPTION OF PARTS 2 1 6 5 5 3 7 4 8 1. Front panel in tempered glass 2. Upper air intake grille 3. Hot air delivery flap 4. Base V 09/16 5. RGB LED side strip (can be deactivated) 6. Side control panel 7. Hooks for wall mounting 8.
HOW TO INSTALL THE ELECTRIC FIREPLACE The fireplace can be used on the floor, after installation of the rectangular base, or alternatively it can be wallmounted using the specific accessories supplied. INSTALLATION KIT COMPONENTS 1. SCREWS - M4 x 8 mm x 12 2. LARGE PLUG x 5 3. SCREWS – M5 x 50 mm x 5 FIREPLACE COMPONENTS TO ASSEMBLE 1. Panel in tempered glass 1. Firebox support structure 1. Fireplace base plate 2. Firebox 3. Wall mounting brackets 2. Front support bracket 3.
Use the appliance to dry clothing. Use the appliance outdoors. MINIMUM DISTANCES between the top of the wall-mounted fireplace and the ceiling: 30 cm. between the bottom of the wall-mounted fireplace and the floor: 20 cm. from the sides of the fireplace: 10 cm. from the front panel of the fireplace: 50 cm. WALL MOUNTING WARNING! DO NOT CONNECT THE APPLIANCE TO THE MAINS POWER SUPPLY BEFORE INSTALLATION Argoclima S.p.A.
2. 3. Placing the bracket against the wall, use a pencil to mark the 4 points on the wall where you need to make the holes for the rawlplugs. Adhere to the above minimum distances from the walls. Using an electric drill (not supplied) at low speed, drill 4 holes of 5/16 inch diameter to a depth of at least 1.5 inches, on the marked spots. 4. 5. Insert 4 large plugs (2) into the holes with a hammer until they are flush with the wall.
NOTE: Pebbles and crystals provided as optional can be replaced by the block of wood. 8. Lift the glass panel into place, and then move it and secure it to the firebox, ensuring that the 2 hooks on the rear of the upper part of the panel engage securely with the slots on the top of the firebox as shown (1). NOTE: We recommend that this operation be performed by two people in order to avoid damage to the glass panel or the firebox. 9.
MOUNTING PORTABLE FIREPLACE In the packaging the fireplace is also provided with a base for use as a portable device. The procedure for assembly of the fireplace is as follows. 1. Align and fix the top support bracket of the firebox to the base with four M4 screws (1) and fully tighten the screws with a Phillips screwdriver. Hooks positioned frontally The top hooks locate at the front Uppertop firebox support Table support Firebox base Table top base 2.
4. 5. Position the firebox on the upper support bracket so that the hooks of the support are inserted correctly into the slots at the bottom of the firebox and the rear mounting holes overlap. Insert 3 M4 x 8 mm screws (1) through the mounting holes and tighten securely with a Phillips screwdriver, as shown in the figure below. Firebox Firebox Table support Uppertop firebox support Firebox Firebox Table support Uppertop firebox support 6. 7.
Installation of the appliance on the base is now complete. NOTE: Use the handle for transporting the appliance. HOW TO USE THE FIREPLACE Place the fireplace in the vertical position on a flat and stable surface. Use the carrying handles. Connect the power cord to a suitable electric socket (220-240V~/50Hz). This fire has LEDs (Light Emitting Diode) rather than conventional light bulbs. LEDS generate the same light levels as conventional bulbs but consume only a fraction of the energy.
CONTROL PANEL REMOTE CONTROL 1. 3. 4. 2. 5. 3. 4. 5. 6. 2. 1. 1. "POWER" button 2. Flame effect button 3. Sleep timer 4. Side RGB LED button 5. TEMPERATURE button: thermostat activation and temperature control panel) 6.
REMOTE CONTROL Side LED selection/off button Thermostat on/off button "POWER" button Flame effect (7 variations) selection button TIMER button Temperature selection button Use Lithium/Manganese button cells, model no. CR2025 -3 V, compliant with Battery Directive no. 2006/66/EC (supplied with the remote control). HOW TO INSERT / REMOVE THE REMOTE CONTROL BATTERIES (refer to the diagram below) Open the battery cover on the back of the remote control (press and pull the rear cover).
POSSIBLE SOLUTIONS TO PROBLEMS POSSIBLE SOLUTION PROBLEM The fireplace will not turn on Ensure that the ON/OFF switch is at I. Replace the fuse (13 amp) in the plug. The fireplace does not emit heat The fireplace is fitted with a thermostat to save energy. If the room temperature is higher than the set temperature, the unit does not produce heat. If you set a higher temperature, the fireplace will begin to emit heat. The fireplace switches off after a Check that the temperature is not set at minimum.
