DA2V2 02 OWNER’S MANUAL 04 ILLUSTRATIONS 06 CONNECTIONS 09 SPECIFICATIONS 09 TROUBLESHOOT 10 RECOMMENDATIONS ww w. a r g on au d i o.
DA2V2 Owner’s manual Dear Customer, Quality has always been our driving force and founding Argon Audio is a natural extension of this philosophy. We have 20 years’ experience in creating and specifying high quality products, manufacturing them and selling them on to end users with Value-for-Money as the primary aim. And Argon Audio is a brand fully compliant with these values.
Connecting your DA2V2 We recommend that you read the manual of your other components carefully before connecting your DA2V2. Please switch off all equipment when connecting your DA2V2. The binding posts on the loudspeaker terminal accepts wire up to Ø 4mm or cables with banana plugs.
DA2V2 Front panel “ON” or “STANDBY MUTE the sound Infra Red Eye for remote 1) Analogue line-in 2) OPTICAL Digital input 3) OPTICAL Digital input 4) USB AUDIO Digital input Volume control Notice: The above buttons marked with 1-4 are all input selectors that each corresponds to a connection on the back side of DA2V2. ww w. a r g on au d i o.
DA2V2 Rear panel and connections Out put for active subwoofer Connections to left and right Passive speakers Fuse holder, if fuse needs to be replaced only use same type and value. IMPORTANT; remember to unplug the power cable from mains socket before opening the fuse holder Input for analogue player, CD player etc.
DA2V2 Remote control DA2 comes with a remote control. The remote control is a system remote control that also can control Argon iNet6+ which is an Internet tuner in same family as DA2. The section with the white square around is dedicated to DA2, as well as the Red Power “ON” button saying “DA2”. The rest of the controls on the remote are dedicated iNet6+ (see page 10) Notice: Controlling Bass, Treble and Balance levels can only be done via the remote.
DA2V2 Connecting your speakers Connect the RED (+) and BLACK (-) terminals from the left speaker to the corresponding terminals on the DA2V2. Connect the RED (+) and BLACK (-) terminals from the right speaker to the corresponding terminals on the DA2V2. Use good speaker cable, to enhance sound quality. Expect to pay around 4-6US$ pr meter. The binding posts on the DA2V2 terminals accepts wire up to Ø 4mm or cables with banana plugs. Insulation on cable must be stripped on all ends. .
Use of digital audio connection DA2V2 Your Argon DA2V2 has 3 digital inputs Optical digital 1 Optical digital 2 USB audio digital The Optical digital connections are typically used for; newer TV’s, hi-fi products such as CD player, DVD players, Digital tuners (like Argon iNet6+). Take a look at the back side of your audio source product and see what kind of digital output it has. Notice; when using Optical cables, remember to remove the small plastic protection from each end of the optical cable.
DA2V2 Notice: If DA2V2 is connected with a Argon iNet6+ they have to be connected only by Optical digital out/in. If iNet6+ is connected to DA2V2 via analogue RCA the volume function on the remote will not work properly Power Management (Auto Stand-by) According to the EC regulations implemented January 1st. 2013 Argon Audio DA2V2 will automatically go into auto standby if it is without a music signal for 20 minutes. This rule is applied by the EC in order to save power consumption.
DA2V2 Recommendation Argon DA2V2 is part of a small family that also consists of iNet6+. iNet6+ is like DA2V2 a full digital product. iNet6+ is basically an Internet based tuner. Besides access to thousands of Internet radio stations, iNet6+ also has digital DAB+ radio and streaming functionality from PC or UpnP drives. If you are into the digital Internet era of streaming music, and if you want to complete the Argon family we strongly recommend you to try out iNet6+.