Assembly Instructions

Assembly Instructions Assembly Instructions
Stage 1 – Fitting the BlindStage 1 – Fitting the Blind
2. Use Screws 1 to fix the Bracket C
in the desired location.
NOTE: Ensure the location allows
the b
lind to sit horizontally when
fitted or parallel to the window
when fitted on the ceiling. See
fig. 4 and 5.
NOTE: Ensure two Brackets are
lock with the headrail of the
Blind.
NOTE: Ensure both brackets are
fitted to the same height
horizontally. See fig. 4.
4. Insert Blind A into Center
Bracket . See fig. 6.
3.
Use Screws to fix Center
Support to the center of the
two brackets . The side with
2 screw holes should fit to the
ceiling.
See fig. 4 and 5.
1. Select the mounting method
e
nsuring t
he total width of the blind
can fit to the location.
• I
nside Mounting - fit to the inside
of the window frame. See fig. 1.
• Outside Mounting - fit to the
out
side of the window frame. See
fig. 2.
• Ceiling Mounting - Fit to the
ceiling above the window frame.
See fig. 3.
NOTE: The safety stoppers on
the cords need to be moved
to a position just above the
breakaway device before the
blind can be lowered.
Please do this before
installation. See fig. 13.
Before fitting select the desired
method of mounting the blind.
5.
Slide the headrail of the Blind
into the Bracket , make sure the
blind cord face to you. To adjust
this blind to fit your inside window
measurement. Please use the
bracket with the screw provided
to secure the blind in place.
See fig. 7.
C
C
1
D
C
NOTE: For fixing into wood
drill small holes to a depth of
15mm using a 2mm drill bit
and screw the bracket into
place.For fixing into brick drill
the holes using a 5mm drill bit
to a depth of 25mm. Insert the
wall plugs and screw the
bracket into place.
NOTE: Center support
is only
included in wide blinds. See
components for reference.
Assembly Instructions Assembly Instructions
Stage 2 – Shorten the BlindStage 1 – Fitting the Blind
fig. 12
F
8. Use Screw 1 to fix the Hold Down
Brackets F . See fig. 10.
At the Bottom of the window
(Optional)
9. Hole o
n end cap of the bottom
rail fit
s into Hold Down Brackets
at the end of the window.
See fig. 11.
NOTE: Before fitting you can
custom fit the blind to the
correct height.
Caution: Goods can not be
returned a
fter customizing
check all size before you
cut or modify any parts
1. The Height : When the blind is fully
lowered. T
here should be no slats
over lapping at the bottom of the
blind. If over lapping occurs you
can r
emove slats to allow a custom
fit.
NOTE: It would be useful to ask
someone to help you at this
stage.
2. Hold the blind at the desired
l
ocation a
nd allow it to fully lower.
In the open position the slats
should be approximately 2cm
apart.
3. Lay blind on a flat surface and
remove the caps on the bottom
e
nd s
lat. The caps are attached to
the lift cords. See fig. 14.
NOTE: In the open position, slats
are approximate 2cm apart. A
good r
ule of thumb is to remove
8 s
lats for every six inches you
wish to shorten the blind.
fig. 14
fig.13
Slacken the cord around
the safety stopper
allowing it to be moved
down the cord.
fig. 1
1
fig. 3
fig. 2
1
1
C
C
1
1
1
2
1
fig. 5
Ceiling Mounting
Wall Mounting
C
D
D
fig. 9
fig. 7
fig. 4
fig. 6
fig. 8
D
D
D
A
6. Slide the Bracket Face Plate
into the Bracket . See fig.8.
H
C
7. Place the Wand B into the
Blind . See fig. 9.
A
F
C
C
A
A
A
A
C
C
H
fig.10
fig.11
B
F