Assembly Instructions

Assembly Instructions Assembly Instructions
Stage 3 – To Operate BlindsStage 2 – Shorten the Blind
fig. 15
fig. 17
fig. 18
fig. 16
Lowering :
WARNING:
WARNING:
level and push to left pulling
down gently until cord lock
releases.
Allow cord to slip through
fingers until blind reaches
desired level.Move pull
cord to the right and the
blind will lock automatically.
Raising:
Tilt:
Important:
4. Cut lift cord 2cm above cap
and remove. Pull the lift cord
from these slats to allow
them to slide out o
f the
ladder r
ung. See fig. 15.
5. C
ount the number of slats you
wish to rem
ove. Pull lift cord
from th
ese slats to allow
them to slide out of the
ladder rung. See fig. 16.
6. R
emember to allow for the
bottom end s
lat to be
reinserted. R
einsert the lift
cord t
hrough the cap holes
and then insert back
through the top and the
caps. See fig. 17.
7. Knot lift cord directly beneath
caps and c
ut off excess cord.
Allow o
ne extra rung and
cut off excess ladder, n
ow
tuck rema
ining ladder into
the b
ottom end slat cap
holes. Replace c
aps.
See f
ig. 17 and 18.
8. After blind is shortened
you may wish to adjust
the pull cord length, this
is best done where the
cords enter the plastic
safety device (Fig.20).
Gently pull the cords
apart just above the
device to open and
release the cords.
Shorten each cord and
re-knot at the end of each
cord before re-assembling.
9
. Use the screws provided to
fixthe cord cleat E to the
wall on the right of the blind.
The cleat should be as
close to the head rail as
possible and a minimum
of 1.5m from the floor.
Always secure the cords
around the cleat as shown
in figure 19 so cords are
out of the reach of children.
See fig.19
fig. 20
2 pull cords condition
fig. 19
Care and Maintenance
Storage,handling and transportation
When storage, put the products in dry and ventilated place.
Need at least one adult for handling and transportation.
Cleaning
As with all surfaces clean with a damp cloth and mild detergent, do not use
bleach or abrasive products.
Fitting
From time to time check to ensure the screws remain tight.
Frequently examine the installation for signs of wear or damage to cables.
Do not use if repair is necessary
.
Argos Limited
Avebury, Milton Keynes, MK92NW.
www.argos.co.uk
Children can strangle if this device
is not installed and adjusted. Read
carefully the instructions and install
accordingly.
Head rails shall not be installed less
than 1.5m from the floor.
A safety device is fitted to the cords
of this blind, it will open and release
the cords if something becomes
caught in the cord loops.
To re-assemble after the cords have
been released, or after shortening
the cords, re-insert the cords into
the device as illustrated fig.20.
Please ensure there is a knot on the
end of each individual cord before
clipping the device back together.
It is mandatory to use the cleat
provided in this pack during the
installation of this blind.
The cleat should be adjacent to
the blind and not less than 1.5m
from the floor.
Test the device if not used
regularly and replace the device
if it is faulty.
Pull cord downward until
blind reaches desired
height, release cord, the blind
locks automatically.
Rotate”Tilt Rod”on left side
of blind to attain desired slat
positions.
Always tilt blind horizontally
before rasing or lowering the
blind this increases the life
of the blind.
Once hung please cut
the pull cords to the
shortest operation a
length and install cleat
on wall to avoid any
risk of strangulation.
3 pull cords condition
1
E