Normandy - 5 Drawer Chest Assembly Instructions - Please keep for future reference 428/2611 414/2081 411/7717 Dimensions Width - 75cm Depth - 39.6cm Height - 90.
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 33kgs. Please lift with care. • Make sure you have enough space to layout the parts before starting. • Check you have all the components and tools listed on pages 2 and 3. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups.
If you have damaged or missing components, call the Customer Helpline: 03456 400800 quoting the reference Components - Panels numbers below Please check you have all the panels listed below 3 Top (D2363A) (75 x 39.6cm) 1 Left Side (DF3875) (88.6 x 37.2cm) 5 Drawer Front (D2366A) (73.7 x 16.2cm) x 5 2 Right Side (DF3876) (88.6 x 37.2cm) 6 Left Drawer Side (W370-124LH) (37 x 12.4cm) x 5 4 Rail (D2370A) (71.7 x 6cm) x 3 7 Right Drawer Side (W370-124RH) (37 x 12.
Components - Fittings Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Assembly Instructions If you have damaged or missing components, call the Customer Helpline: 03456 400800 quoting the reference numbers below Step 1 B Prepare the 5 drawer fronts Screw 2 metal dowels B into the holes shown on the back of each drawer front 5 . B 5 x5 Step 2 Prepare the drawer sides D D Insert a small locking nut D into the hole shown on the left drawer side 6 and right drawer side 7 .
Assembly Instructions Step 4 Fit the drawer base 7 11 Slide the drawer base 9 down the grooves in the drawer sides 6 and 7 then down into the groove in the drawer front 5 . 9 6 x5 5 Step 5 J J Fit the drawer back Fit the drawer back 8 between the drawer sides 6 and 7 . Make sure that the drawer base 9 fits into the groove in the drawer back 8 . 8 7 9 J J x5 6 6 Hold the drawer back 8 in position and tap the knock-in pegs J through the holes in the drawer sides 6 and 7 .
Assembly Instructions Prepare the left side F Finished front edge Step 8 H a: Place 5 runners H on left side 1 . Slide back top of runner and use 2nd hole from the front to fit 1st screw F . b: Slide the runner H back the other way and fit the 2nd screw F into the corresponding hole in the left side 1 . F F a: F H F Finished front edge H F H H 1 H c: Insert 1 large locking nut C into the left side .1 .
Assembly Instructions Step 9 H a: H a: Place 5 runners H on right side 2 . Slide back top of runner and use 2nd hole from the front to fit 1st screw F . F F H H F F F Finished front edge 2 b: F Slide the runner H back the other way and fit the 2nd screw F into the corresponding hole in the right side 2 . H c: Insert 1 large locking nut C into the right side 2 . Tap a wooden dowel A into the right side 2 . F b: F F F Screw 3 metal dowels B into the right side 2 .
Assembly Instructions Step 10 C Prepare the 3 rails x3 A p Insert 2 large locking nuts C into each of the rails 4 . in la C d ar o b ip ch Tap 2 wooden dowels A into each of the rails 4 . a rf su 4 ce A Step 11 B Fit the 3 rails Push the 3 rails 4 onto right side 2 as shown. Use a screwdriver to tighten the large locking nut C fitted to each of the 3 rails 4 .
Assembly Instructions Step 12 Fit the left side Fit the left side 1 to the 3 rails 4 . 4 Use a screwdriver to tighten the large locking nut C fitted to each of the rails 4 . 4 Carefully stand the unit up. 1 4 Warning: The unit is heavy. Lift with care. Step 13 B Prepare the top Screw 2 metal dowels B into the top 3 . 3 Note: Tighten metal dowels up fully against the panel.
Assembly Instructions Step 14 Fit the top 3 Lower the top 3 onto the side panels 1 and .2 . 2 Use a screwdriver to tighten the 2 large locking nuts C fitted to the inside of the left side . 1 and right side 2 . Carefully lay the unit down onto its front again. Rounded front edge 1 Warning: The unit is heavy. Lift with care.
Assembly Instructions Step 16 Fit the 4 plastic nails Tap 2 plastic nails K into the bottom edge of each of the sides 1 and .2 . K 2 K K 1 Carefully stand the unit up for the next step. K Warning: The unit is heavy. Lift with care. Step 17 Fit the drawers Starting with the bottom drawer, slide both the runners H forward and locate the drawer sides 6 and 7 between them, lining up the holes in the drawer wrap with the 2nd 'threaded' holes in the runners H .
Assembly Instructions Step 18 Example Attach the strap to the wall M Strap M Screw Washer Strap IT Washer N To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by fitting of the overbalance protector kit .M to the unit, or an alternative fixing method of your choice. Wall fixing (not supplied) Attach the strap to the unit U Fit the overbalance protector kit Screw (not supplied) Wall fixings are not supplied as they will need to suit the wall type.
ALR3173