Kensington - 3+2 Drawer Chest Assembly Instructions - Please keep for future reference 428/3531 425/9802 Dimensions Width - 48.5cm Depth - 39.4cm Height - 97.4cm MADE IN BRITAIN Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928.
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 33kgs. Please lift with care. • Make sure you have enough space to layout the parts before starting. • Check you have all the components and tools listed on pages 1, 2 and 3. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups.
Components - Panels If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the panels listed below 3 Divider (DF3771) (19.8 x 37.2cm) 1 Left Side (DF2693) 2 Right Side (DF2694) 5 Rail (DF2406) 6 Front Plinth (DF2408) (95.9 x 37.4cm) (64.
Components - Fittings If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Assembly Instructions Step 1 Prepare the 2 small drawer fronts Screw 2 metal dowels A into each of the small drawer fronts 8 . A A A Note: Tighten the metal dowels up fully against the panels. x2 8 Step 2 Prepare 2 pair of drawer sides Insert a small locking nut C into the hole shown on the left drawer side 10 and the right drawer side 11 . C C C 11 10 x2 x2 Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Assembly Instructions Step 4 Fit the small drawer base 14 Slide the small drawer base 14 down the grooves in the drawer sides 10 and 11 and down into the groove in the small drawer front 8 . x2 11 10 8 Step 5 Fit the small drawer back Fit the small drawer back .12 between the drawer sides 10 and 11 . Make sure that the small drawer base 14 fits into the groove in the small drawer back 12 .
Assembly Instructions Step 8 A Prepare the 3 large drawer fronts Screw 2 metal dowels A into each of the large drawer fronts 9 . A A x3 9 Note: Tighten the metal dowels up fully against the panels. Step 9 Prepare 3 pair of drawer sides Insert a small locking nut C into the hole shown on the left drawer side 10 and the right drawer side 11 . C C C 11 10 x3 Note: The arrow on the locking nut must point towards the hole in the edge of the panel.
Assembly Instructions Step 11 Fit the large drawer base x3 15 11 Slide the large drawer base 15 down the grooves in the drawer sides 10 and 11 and down into the groove in the large drawer front 9 . 10 9 Step 12 Fit the large drawer back Fit the large drawer back .13 between the drawer sides 10 and 11 . Make sure that the large drawer base 15 fits into the groove in the large drawer back 13 .
Assembly Instructions Step 15 J Prepare the left side M a: Place 4 runners M on the left side 1 as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw J . J J M J b: Slide the runner M back the other way and fit the 2nd screw J into the corresponding hole in the left side 1 . J Finished front edge M 1 M a: M c: Screw 8 metal dowels A into the left side 1 . Insert 2 large locking nuts B into the left side .1 .
Assembly Instructions Step 16 J Prepare the right side M a: Place 4 runners M on the right side 2 as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw J . b: Slide the runner M back the other way and fit the 2nd screw J into the corresponding hole in the right side 2 . J J 2 J a: J M M M M Finished front edge c: Screw 8 metal dowels A into the right side 2 . J J Insert 2 large locking nuts B into the right side 2 .
Assembly Instructions Step 17 J Prepare the divider Note: Due to the manufacturing process, the 2 holes for the large locking nut can be on either surface of the divider. M a: J Finished front edge M 3 a: Place a runner M on the divider 3 as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw J . Finished front edge J b: 3 b: Slide the runner M back the other way and fit the 2nd screw J into the corresponding hole in the divider 3 .
Assembly Instructions Step 18 B Prepare 2 of the rails A D Insert 2 large locking nuts B into each of the 2 rails 5 . B 5 Tap 2 wooden dowels D into each of the 2 rails 5 . x2 Screw a metal dowel A into each of the 2 rails 5 . D Step 19 Fit 2 of the rails to the divider Remember: The large locking nuts can be on either surface of the divider. Push 2 rails 5 onto the divider 3 . Use a screwdriver to tighten the 2 large locking nuts B fitted to the divider 3 .
Assembly Instructions Step 21 Prepare the other 6 rails B D Insert 2 large locking nuts B into each of the 6 rails 5 . B x6 5 Tap 2 wooden dowels D into each of the 6 rails .5 . D Step 22 Fit another rail Push another rail 5 onto the right side 2 . Use a screwdriver to tighten the large locking nut B fitted to the rail 5 . 2 3 5 F Secure the rail 5 to the bottom edge of the divider 3 using screw F . Step 23 Fit the other rails 2 5 Push the remaining 5 rails 5 onto the right side 2 .
Assembly Instructions Step 24 Fit the left side 5 Push the left side 1 onto the rails 5 . 5 5 5 Use a screwdriver to tighten the large locking nut B fitted to each of the rails 5 . Step 25 5 5 5 5 1 A A Prepare the top Screw 4 metal dowels A into the top 4 . A A 4 Profiled front edge Step 26 Fit the top Note: To make it easier to fit the top and plinths, place polystyrene blocks from the packaging underneath the side panels to raise the assembly. Push the top 4 onto the assembly.
Assembly Instructions Step 27 a: Fit the back The measurement from top corner X to bottom corner X must be equal to the measurement from top corner Y to bottom corner Y a: Square up the unit by making sure that measurement x to x equals y to y. b: Place the back b: x P 16 onto the unit. y Nail P around the outside edges of the back 16 . 16 y Note: Nails should be spaced about 150mm apart.
Assembly Instructions Step 29 Finished top edge B Prepare a side plinth Insert a large locking nut B into 1 of the side plinths 7 . 7 D Tap a wooden dowel D into the side plinth 7 . Step 30 Prepare the other side plinth B D Finished top edge Insert a large locking nut B into the side plinth .7 . 7 Tap a wooden dowel D into the side plinth 7 . Step 31 A Prepare the front plinth Profiled top edge Screw 2 metal dowels A into the front plinth 6 .
Assembly Instructions Step 33 Fit the plinths Position the 3 plinths around the outside of the assembly, ensuring that the bottom edge of the plinths are flush with the bottom edge of the sides, as shown. Secure the 2 side plinths . 7 through the left end . 1. and right end 2 using screws G . 7 2 G G G 1 7 G Carefully stand the unit up for the next step. Profiled top edge 7 Warning: The unit is heavy. Lift with care.
Assembly Instructions Step 35 O Strap O Strap Washer IT Wall fixing (not supplied) Attach the strap to the unit N To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by fitting of the overbalance protector kit .O to the unit, or an alternative fixing method of your choice. Attach the strap to the wall U Fit the overbalance protector kit Example Screw (not supplied) Wall fixings are not supplied as they will need to suit the wall type.
ALR3176
