Seville - 5 Drawer Chest Assembly Instructions - Please keep for future reference 184/9198 145/0862 184/8319 Dimensions Width - 66cm Depth - 33cm Height - 91cm MADE IN BRITAIN Important - Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 21kgs. Please lift with care. • Make sure you have enough space to layout the parts before starting. • Check you have all the components and tools listed on pages 2 and 3. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups.
Components - Panels If you have damaged or missing components, call the Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.
Components - Fittings If you have damaged or missing components, call the Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number and the reference numbers below) Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Assembly Instructions If you have damaged or missing components, call the Customer Helpline: 0870 112 1928 or email: Help@ClickSpares.co.uk (quoting your original order number and the reference numbers below) Step 1 B Prepare the drawer fronts Plain chipboard surface B Screw 2 metal dowels B into each of the drawer fronts 5 . B 5 Note: Tighten the metal dowels up fully against the panel.
Assembly Instructions Step 4 Fit the drawer front 6 Turn drawer wrap 6 assembly over and push it onto the back of the drawer front 5 . C 6 5 B B Note: Turn the locking nuts C clockwise to secure the panels - more than 1/2 a turn. 5 x5 Step 5 Attach the drawer stops Carefully break off 2 drawer stops (F599) from a set of drawer runners .I . Push the drawer stops fully through the drawer wrap 6 from the inside.
Assembly Instructions Step 7 Prepare the left side L Finished front edge F600 I Separate the runners I . I I I Push fit 5 left runners I marked ‘L’ into the left side 1 . I I Note: Runners must be be fitted flat against the panel. If necessary gently tap into final position. 1 Step 8 Prepare the right side I Push fit 5 right runners I marked ‘R’ into the right side 2 . I 2 Finished front edge I Note: Runners must be be fitted flat against the panel.
Assembly Instructions Step 10 D Join the top to the right side Push the top 3 onto the right side 2 and secure with 2 screws D . Step 11 D 2 3 Finished front edge Finished front edge A Prepare the plinth in la p ce fa r su 4 d ar o b p i ch Tap 2 wooden dowels A into the plinth 4 .
Assembly Instructions Step 12 Join the plinth to the right side Push the plinth 4 onto the right side 2 and secure with screw D . 2 D in la p d ar o b ip ch ce a rf su 4 Support the plinth until the left side has been fitted in the next step. Step 13 Fit the left side Push the left side 1 onto the assembly and secure with 3 screws D .
Assembly Instructions Step 14 a: Fit the back The measurement from top corner X to bottom corner X must be equal to the measurement from top corner Y to bottom corner Y a: Square up the unit by making sure that measurement x to x equals y to y. b: Place the back x b: F 8 onto the unit. Nail F around the 3 edges of the back 8 , as shown. 8 y x Note: Nails should be spaced about 150mm apart. Stand the unit up for the next step. Warning: The unit is heavy. Lift with care.
Assembly Instructions Step 15 Insert the drawers Lift the front of the drawers whilst inserting to overcome the ‘stop’ system. Note: To ensure that your drawers run smoothly, spray a small amount of furniture polish into the grooves.
Assembly Instructions Step 16 H Strap H Screw Washer Strap Washer IT Wall fixing (not supplied) Attach the strap to the unit N To prevent possible overbalancing we recommend that this unit is secured to a suitable wall by fitting of the overbalance protector kit .H to the unit, or an alternative fixing method of your choice. Attach the strap to the wall U Fit the overbalance protector kit Example Screw (not supplied) Wall fixings are not supplied as they will need to suit the wall type.
