Kensington - 3DrawerBedside Assembly Instructions - Please keep for future reference 423/7824 426/5487 Dimensions Width - 48.5cm Depth - 39.4cm Height - 76.1cm MADE IN BRITAIN Important -Pleasereadtheseinstructionsfullybeforestartingassembly If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928.
Safety and Care Advice Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 20kgs. Please lift with care. • Make sure you have enough space to layout the parts before starting. • Check you have all the components and tools listed on pages 1, 2 and 3. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups.
Components - Panels If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the panels listed below 1 LeftSide (DF2404) 2 RightSide (DF2405) (74.6x37.4cm) (74.6x37.4cm) 4 Rail (DF2383) (42.3x9.2cm)x5 7 DrawerFront (DF2384) (41.
Components - Fittings If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928. For any other queries please contact the Customer Helpline on: 0345 640 2020 Please check you have all the fittings listed below Note:The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Assembly Instructions Ifyouhavedamagedormissingcomponents,callthe CustomerHelpline:03456400800quoting the reference numbers below Step 1 A Preparethe3drawer fronts Screw 2 metal dowels A into each of the drawer fronts 7 . A A x3 7 Note: Tighten the metal dowels up fully against the panels. Step 2 Preparethedrawer sides C Insert a small locking nut C into the hole shown on the left drawer side 8 and the right drawer side 9 .
Assembly Instructions Step 4 Fitthedrawerbase Slide the drawer base 11 down the grooves in the drawer sides 8 and 9 and down into the groove in the drawer front 7 . 11 x3 9 8 7 Step 5 Fitthedrawerback Fit the drawer back 10 between the drawer sides 8 and 9 . Make sure that the drawer base 11 fits into the groove in the drawer back 10 . Hold the drawer back 10 in position and tap the knock-in pegs F through the holes in the drawer sides 8 and 9 .
Assembly Instructions Step 8 J Preparetheleftside M a:Place 3 runners M on the left side 1 as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw J . b:Slide the runner M back the other way and fit the 2nd screw J into the corresponding hole in the left side 1 . Finished frontedge J J J M 1 M a: M c:Screw 5 metal dowels A into the left side 1 . Finished frontedge Insert 2 large locking nuts B into the left side .1 .
Assembly Instructions Step 9 J Preparetherightside M a:Place 3 runners M on the right side 2 as shown. Slide back the top of runner and use the 2nd hole from the front to fit the 1st screw J . b:Slide the runner J J 2 M J M M back the other way and fit the 2nd screw J into the corresponding hole in the right side 2 . a: M Finished frontedge c:Screw 5 metal dowels A into the right side 2 . J Insert 2 large locking nuts B into the right side 2 .
Assembly Instructions Step 10 Preparethe5rails B D B Insert 2 large locking nuts B into each of the 5 rails 4 . x5 4 Tap 2 wooden dowels D into each of the 5 rails 4 . D Step 11 A Fit3oftherailstothe rightside B Push 3 rails 4 onto the right side 2 . 2 Use a screwdriver to tighten the large locking nut B fitted to each of the rails 4 . 4 4 4 Note: Turn the large locking nuts B as far as they will go - more than 1/2 a turn.
Assembly Instructions Step 13 Fittheleftside Push the left side 1 onto the rails 4 . 4 4 4 Use a screwdriver to tighten the large locking nut B fitted to each of the rails 4 . 1 4 4 A Step 14 A A Preparethetop A Screw 4 metal dowels A into the top 3 . 3 Profiled frontedge Step 15 Fitthetop Note: To make it easier to fit the top and plinths, place polystyrene blocks from the packaging underneath the side panels to raise the assembly. 3 2 1 Push the top 3 onto the assembly.
Assembly Instructions Step 16 a: ThemeasurementfromtopcornerXtobottomcornerXmustbe equaltothemeasurementfromtopcornerYtobottomcornerY Fittheback a: Square up the unit by making sure that measurement x to x equals y to y. b: x E b: Place the back 12 y onto the unit. Nail E around the outside edges of the back 12 . 12 y x Note: Nails should be spaced about 150mm apart. Step 17 Fitthe4plasticnails Tap 2 plastic nails L into the bottom edge of each of the sides 1 and .
Assembly Instructions Step 18 Finished topedge B Prepareasideplinth Insert a large locking nut B into 1 of the side plinths 6 . 6 D Tap a wooden dowel D into the side plinth 6 . Step 19 Preparetheotherside plinth B D Finished topedge Insert a large locking nut B into the side plinth .6 . 6 Tap a wooden dowel D into the side plinth 6 . Step 20 A Preparethefront plinth A Profiled topedge Screw 2 metal dowels A into the front plinth 5 .
Assembly Instructions Step 22 Fittheplinths Position the 3 plinths onto the assembly ensuring that the bottom edge of the plinths are flush with the bottom edge of the sides, as shown. Secure the 2 side plinths . 6 through the left end . 1. and right end 2 using screws G . 6 1 G G 2 6 G G 6 Carefullystandthe unitupforthenext step.
Assembly Instructions Step 24 O Strap Strap Washer Screw (not supplied) Wall fixings are not supplied as they will need to suit the wall type. Note: Take care when drilling the wall that you do not drill into any pipes, wires etc. If in doubt, consult an expert. Assemblyiscomplete If you need help or have damaged or missing parts, please visit www.argos-support.co.uk or email: Help@ClickSpares.co.uk (quoting your original order number) Alternatively, call the Spares Helpline on: 0370 112 1928.
ALR3179
