DR899153 New Hallingford 3 Door 3 Drawer Wardrobe Assembly Instructions - Please keep for future reference 2278380 2745253 Tip : To prevent damage, we recommend that you build your unit on the carton(s) it was packed in.
Safety and Care Advice Important – Please read these instructions fully before starting assembly • Check you have all the components and tools listed on pages 2 and 3. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups. • Assemble the item as close to its final position (in the same room) as possible.
Components - Panels If you have damaged or missing components, call the Customer Helpline: 03456 400 800 Please check you have all the panels listed below 1 Left side (205.6 x 58cm) P2349b 5 Top/Bottom x 2 (145.8 x 57.7cm) P1350 9 Drawer base x 3 (45.4 x 34.9cm) BO33955B 2 Right side (205.6 x 58cm) P2349b (47.5 x 57.7cm) P2893 (35 x 46.7 x 10cm) LA1869 4 Door x 2 7 Large horizontal 8 Small horizontal 11 Drawer front x 3 12 Shelf (199.2 x 48.8cm) P3304 (196.9 x 57.
Components - Fittings Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. FK1324 A FK1980 B 40mm Screw x 9 C 9mm Srew x 6 20mm Screw x 12 D F E 10mm Fixing screw drawer x 12 FK1235 H L-Bracket x 1 24mm locking screw x 32 FK1012 I Large locking nut x 26 FA1515 FK1010 K Small locking nut x 6 12.
Assembly Instructions Step 1 J Drawer assembly x 3 a: Insert two small locking nuts J into drawer wrap 0. a: Make sure the ‘arrow’ on J is pointing towards the hole in the edge of 0 10 J b b: Screw 24mm locking H screws H into holes shown on back of drawer front !. Make sure 24mm locking screws H are tightened right up against drawer front !. H 11 H 11 c: Slide drawer base 9 into grooves shown on drawer wrap 0.
Assembly Instructions Step 1 - continued d: Turn the drawer wrap assembly over and push onto drawer front !. Use a philips or flatblade screwdriver, that is a good fit, to turn small locking nut J as far as it will go - more than 1/2 turn. d J J 11 J H e: Fix drawer handle T onto drawer front ! using 30mm screw B. Turn over drawer and slide Drawerbase supports W in corner as shown and fix them, using the attached screws .
Assembly Instructions Step 2 - continued b 3 b: Slide top of runners R E O O R back. Fix through 3rd hole of runner R and pre-drilled holes of upright 3 using 10mm fixing screw drawer E. 3 R Fix through 1st and 9th hole of runners R using 15mm screw O. O R Note: there are no predrilled holes for 15mm screw O. O R O E E E O O O Finished front edge Repeat a and b on upright small 6. Step 3 H F H Insert fittings Note: Insert 24mm locking screw H as far as shown.
Assembly Instructions Step 4 A Attaching plinths Align the sides of plinth front ^ with bottom 5 as shown and attach using 40mm screw A. A A A 5 Note: there are no predrilled holes for 40mm screw aA. Note: top and bottom panels 5 are identical. Only prepare one of the panels at this stage. This will be the bottom panel A Top side A 17 16 H Repeat with plinth back &. H Step 5 H 5 Insert locking screws Top side H Screw 24mm locking screw H into bottom 5.
Assembly Instructions Step 7 Insert locking screws H Screw 24mm locking screw H into top 5. 5 H Unfinished back edge Step 8 Attaching panels Two people are needed here. I I I Position top 5, large horizontal 7 and small horizontal 8 onto upright 3. I 3 Insert two Large locking nuts I into upright 3, 3 in large horizontal 7 and 2 in small 8 horizontal where shown. I Use a screwdriver to turn locking nuts I clockwise to lock.
Assembly Instructions Step 10 M I Attaching panels M I Two people are needed here. Position upright small 6 onto bottom 5 and small horizontal 8. Insert two Large locking nuts I into upright small 6 and small horizontal 8 where shown. Use a screwdriver to turn locking nuts I clockwise to lock. 8 I 5 I 6 I I I H N H Step 11 F M Insert fittings H 1 Put board carrier N into right side 2. Screw 24mm locking screws H into left side 1 and right side 2.
Assembly Instructions Step 12 M I M I Attaching panels Two people are needed here. I Position right side 2 and left side 1 onto top and bottom 5. 2 5 I Insert six Large locking nuts I in top and bottom 5, insert 2 large locking nuts I into large horiziontal 7. I I 7 I I I Use a screwdriver to turn locking nuts I clockwise to lock.
Assembly Instructions Step 14 A Attaching pelment and L-bracket Position pelment * onto top 5 as shown, fix by using three 40mm screws A. A 5 18 A Step 15 Insert shelf Position shelf @ onto board carriers N and fix by screwing four 15mm screws O through board carrier N into shelf @.
Assembly Instructions Step 16 Inserting drawers a: b: C a: Pull runners out.Slide drawers onto runners so they butt up against back of drawer front. 2 1st small threaded hole b: Fix through drawer sides into runners using 9mm screwsC . Step 17 Inserting hanger rails Place hanger rails U and V onto hanger rail supports M. U SV M Step 18 Fitting hinges to doors Fix three hinge door Q to each door 4 and mirror door small % using 15mm screws D. Attach door handles T using 30mm screws B.
Assembly Instructions Step 19 Hanging doors c: X a: With help, slot hinge door Q onto hinge back P. a: D G X b: Tighten screw shown to lock hinges in position. P Q b: Repeat a and b for other doors. P See ‘Hinge adjustment’ in step 20 if the doors need adjusting. P Q onto top 5 as shown, fix by using15mm screw D. Note: there are no pre-drilled holes for 15mm screw D. Use X to fix on the wall, please see last page for more information. d: Before adjusting the Use pegs S to square your unit.
Assembly Instructions Step 20 Hinge adjustment a: a: To move doors up or down: loosen screws shown and move doors to suit. Once doors are aligned, re-tighten. b: To move doors in or out: loosen screw shown and move doors to suit. b: Re-tighten screws. c: To move doors left or right: loosen screw shown and move doors to suit. c: Re-tighten screws.
A Guide to - Wall Mounting & Fixings Important: When drilling into walls always check that there are no hidden wires or pipes etc. Important note: If plastic wall plugs are supplied with your product: Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualified tradesperson if you are unsure. Hints: - these are only suitable for use in masonry walls. If you are in any doubt about the correct wall plugs for your wall, seek professional advice.
