Baltimore 855/4819 765/9557 Spare Parts Customer Support Visit: www.argos-support.co.uk Call: 0345 640 2020 Email: Help@ClickSpares.co.
Safety Important - Please read these instructions fully before starting assembly • Warning: This unit weighs approximately 30kgs. Please lift with care. • Assembly to be carried out by a competent adult only. • During assembly children should be kept away from the product due to possible risk of injury. • Installation shall only be carried out exactly according to the manufacturer’s instructions otherwise a safety risk can occur if incorrectly installed.
DF-00012374 Cabinet Panels DF-00012375 3 83.4 x 9.4cm 2 90 x 32.6cm DF-00012376 5 83.4 x 7.6cm DF-00012373 DF-00012372 6 83.4 x 7.4cm 7 89.6 x 32.8cm DF-00012378 DF-00012371 1 90 x 32.6cm DF-00017888 x3 4 83.4 x 9.4cm 8 83.4 x 31.8cm 11 31.6 x 19.8cm x2 x3 W290-165RH 13 29 x 16.5cm DF-00012382 10 86 x 24.6cm 14 29 x 16.5cm x3 T247-287 x3 W290-165LH 12 26.2 x 19.2cm 15 24.7 x 28.7cm x3 W236-165 x2 X860-246 9 83.4 x 31.4cm DF-00012377 DF-00012379 Drawer Panels 16 23.
Fittings Use these drawings to correctly identify the fittings x 18 F x 12 G x6 x 20 H x8 L x 12 D x6 I x 25 M x3 E x2 J x4 N x6 F51 F74 F72 F910 C F91 B F180 x 18 F73 A A F22 F901 F900 Bag 1 A A x6 K x6 F639 F461 F171GY F3 F901 Bag 2
x2 P x3 F1004 O F220 F474 Fittings Q x6 Tools Only used for drilling walls
1 Fitting Ball Bearing Runners www.youtube.
2 C x4 2 1 3 B x4 2 1 4 A x 14 2 1
5 F Fitting Ball Bearing Runners www.youtube.
6 B x2 C x2 3 7 3 11 11 D Finished front edge Finished front edge x2 Finished front edge 8 B x4 C x4 4 4
9 4 4 D x4 Finished front edge 10 2 11 x3 2
12 8 B x4 C x4 13 x2 8 Finished front edge 14 C x2 6
15 6 16 B x4 C x4 4 5
17 x2 4 5 18 x7 1
19 Only use 1 Screw to fit each Bracket A x4 O x2 7 Finished front edge 20 7 Finished front edge
21 x2 7 22 3 E x2 3
23 Squaring up a Chest and fitting the Back Panel www.youtube.
25 J x4 26 WARNING! O x2 In order to prevent overturning this product must be used with the 2 wall attachment devices provided Slide the Brackets against the wall. Fit the 2nd screw supplied with the Brackets into the underside of the Top panel. Mark the slot at the back of the Brackets for drilling into the wall. Wall fixings are not supplied as they will need to suit the wall type. Note: Take care when drilling the wall that you do not drill into any pipes, wires etc.
A Guide to Wall Mounting & Fixings Important note: If plastic wall plugs are supplied with your product: Important: When drilling into walls always check that there are no hidden wires or pipes etc. Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualified tradesperson if you are unsure. Hints: - these are only suitable for use in masonry walls. If you are in any doubt about the correct wall plugs for your wall, seek professional advice.
Drawer Assembly x3 A A x6 K x6 L x 12 M x3 F639 F461 F171GY F3 F901 Bag 2 N x6 Drawer Assembly www.youtube.
29 14 13 12 30 15 31 L x6 16
32 L x6 33 M 34 N x3 x6 P x3
35 Fitting Ball Bearing Runners www.youtube.com/watch?v=yG4xtiJJeSg G x6 For each drawer, slide both the runners forward and locate the drawer sides between them, lining up the holes in the drawer sides with the 2nd 'threaded' holes in the runners. Working from the inside of the drawer, insert 2 screws through the drawer sides and out into the 2nd threaded hole in the runner. Note: Do not overtighten the screws. If they catch on the runner you may need to loosen them slightly.
36 H x8 37 9 9
38 Assembly is complete Please remove any blue protective film from panel edges and clear protective film from panel surfaces ALR3450
