DR899154 New Hallingford 3 Door 3 Drawer Wardrobe Assembly Instructions - Please keep for future reference 2278380 2745253 2749716 2482279 2448282 Dimensions Width - 148,8cm Depth - 60,3cm Height - 205,7cm Tip : To prevent damage, we recommend that you build your unit on the carton(s) it was packed in. Important – Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.
Safety and Care Advice Important – Please read these instructions fully before starting assembly • Check you have all the components and tools listed on pages 2 and 3. • Do not stand or put weight on the product, this could cause damage. • Remove all fittings from the plastic bags and separate them into their groups. • Assemble the item as close to its final position (in the same room) as possible. • Keep children and animals away from the work area, small parts could choke if swallowed.
Components - Panels For damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk Please check you have all the panels listed below 1 Left side (205.6 x 58cm) P2349b 5 Top/Bottom x 2 (145.8 x 57.7cm) P1350 9 Drawer base x 3 (45.4 x 34.9cm) BO33955B 2 Right side (205.6 x 58cm) P2349b (47.5 x 57.7cm) P2893 (35 x 46.7 x 10cm) LA1869 4 Door x 2 7 Large horizontal 8 Small horizontal 11 Drawer front x 3 12 Shelf (199.2 x 48.8cm) P3724 (196.9 x 57.
Components - Fittings For damaged or missing parts, please visit: www.argos-support.co.uk or email: Help@ClickSpares.co.uk Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Assembly Instructions Step 1 J Drawer assembly x 3 a: Insert two small locking nuts J into drawer wrap 0. a: Make sure the ‘arrow’ on J is pointing towards the hole in the edge of 0 10 J b b: Screw 24mm locking H screws H into holes shown on back of drawer front !. Make sure 24mm locking screws H are tightened right up against drawer front !. H 11 H 11 c: Slide drawer base 9 into grooves shown on drawer wrap 0.
Assembly Instructions Step 1 - continued d: Turn the drawer wrap assembly over and push onto drawer front !. Use a philips or flatblade screwdriver, that is a good fit, to turn small locking nut J as far as it will go - more than 1/2 turn. d J J 11 J H e: Fix drawer handle T onto drawer front ! using 30mm screw B. Turn over drawer and slide Drawerbase supports W in corner as shown and fix them, using the attached screws .
Assembly Instructions Step 2 - continued b 3 b: Slide top of runners R E O O R back. Fix through 3rd hole of runner R and pre-drilled holes of upright 3 using 10mm fixing screw drawer E. 3 R Fix through 1st and 9th hole of runners R using 15mm screw O. O R Note: there are no predrilled holes for 15mm screw O. O R O E E E O O O Finished front edge Repeat a and b on upright small 6. Step 3 H F H Insert fittings Note: Insert 24mm locking screw H as far as shown.
Assembly Instructions Step 4 A Attaching plinths Align the sides of plinth front ^ with bottom 5 as shown and attach using 40mm screw A. A A A 5 Note: there are no predrilled holes for 40mm screw aA. Note: top and bottom panels 5 are identical. Only prepare one of the panels at this stage. This will be the bottom panel A Top side A 17 16 H Repeat with plinth back &. H Step 5 H 5 Insert locking screws Top side H Screw 24mm locking screw H into bottom 5.
Assembly Instructions Step 7 Insert locking screws H Screw 24mm locking screw H into top 5. 5 H Unfinished back edge Step 8 Attaching panels Two people are needed here. I I I Position top 5, large horizontal 7 and small horizontal 8 onto upright 3. I 3 Insert two Large locking nuts I into upright 3, 3 in large horizontal 7 and 2 in small 8 horizontal where shown. I Use a screwdriver to turn locking nuts I clockwise to lock.
Assembly Instructions Step 10 M I Attaching panels M I Two people are needed here. Position upright small 6 onto bottom 5 and small horizontal 8. Insert two Large locking nuts I into upright small 6 and small horizontal 8 where shown. 8 I 5 I 6 I Use a screwdriver to turn locking nuts I clockwise to lock. I I Warning: Do not use an electric screwdriver to attach the hinges as this can weaken the fixing. H N H Step 11 F M Insert fittings H 1 Put board carrier N into right side 2.
Assembly Instructions Step 12 M I M I Attaching panels Two people are needed here. I Position right side 2 and left side 1 onto top and bottom 5. 2 5 I Insert six Large locking nuts I in top and bottom 5, insert 2 large locking nuts I into large horiziontal 7. I I 7 I I I Use a screwdriver to turn locking nuts I clockwise to lock.
Assembly Instructions Step 14 A Attaching pelment and L-bracket Position pelment * onto top 5 as shown, fix by using three 40mm screws A. A 5 18 A Step 15 Insert shelf Position shelf @ onto board carriers N and fix by screwing four 15mm screws O through board carrier N into shelf @.
Assembly Instructions Step 16 Inserting drawers a: b: C a: Pull runners out.Slide drawers onto runners so they butt up against back of drawer front. 2 1st small threaded hole b: Fix through drawer sides into runners using 9mm screwsC . Step 17 Inserting hanger rails U Place hanger rails U and V onto hanger rail supports M. SV M Warning: Do not use an electric screwdriver to attach the hinges as this can weaken the fixing.
Assembly Instructions Step 19 Hanging doors c: See page 1 for link to instruction video! X a: With help, slot hinge door Q onto hinge back P. a: D G X b: Tighten screw shown to lock hinges in position. P Q b: Repeat a and b for other doors. P See ‘Hinge adjustment’ in step 20 if the doors need adjusting. P Q onto top 5 as shown, fix by using15mm screw D. Note: there are no pre-drilled holes for 15mm screw D. Use X to fix on the wall, please see last page for more information.
Assembly Instructions Step 20 Warning: Do not use an electric screwdriver to attach the hinges as this can weaken the fixing. Hinge adjustment a: To move doors up or down: loosen screws shown and move doors to suit. a: Once doors are aligned, re-tighten. b: To move doors in See page 1 for link to instruction video! or out: loosen screw shown and move doors to suit. Re-tighten screws. c: To move doors left or right: loosen screw shown and move doors to suit. Re-tighten screws.
A Guide to - Wall Mounting & Fixings Important note: If plastic wall plugs are supplied with your product: Important: When drilling into walls always check that there are no hidden wires or pipes etc. Make sure that the screws and wall plugs being used are suitable for supporting your unit. Consult a qualified tradesperson if you are unsure. Hints: - these are only suitable for use in masonry walls. If you are in any doubt about the correct wall plugs for your wall, seek professional advice.
