Amersham - Corner TV Unit Assembly Instructions - Please keep for future reference 881/4968 Dimensions Width - 120cm Depth - 44cm Height - 50cm Important – Please read these instructions fully before starting assembly If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800 Issue 1 - 17/09/18
Safety and Care Advice Important – Please read these instructions fully before starting assembly Check you have all the components and tools listed on pages 2 and 3. Remove all fittings from the plastic bags and separate them into their groups. Keep children and animals away from the work area, small parts could choke if swallowed. Make sure you have enough space to layout the parts before starting. Do not stand or put weight on the product, this could cause damage.
Components - Panels Please check you have all the panels listed below Top 7 Right side panel (48 x 14.4cm) Top 1 Top panel (120 x 44cm) 8 Left side panel (48 x 14.4cm) underside 9 Right front frame (48 x 9.2cm) 2 Base panel (114.4 x 38cm) 10 Left front frame (48 x 9.2cm) 3 Front frame x 2 (103.6 x 6.5cm) 11 Left back column (48 x 6.5cm) Top 12 Right back column (48 x 6.5cm) 4 Inside panel x 2 (37.5 x 38cm) 13 Large back panel (54 x 30cm) 5 Shelf (36.4 x 37.
Components - Fittings If you have damaged or missing components, call the Customer Helpline: 03456 400 800 Please check you have all the fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required.
Assembly Instructions Step 1 a: Fixing right front frame to the right side panel (Two people required for an easier assembly). a: Insert right side panel 7 into right front frame 9 through joints. c: 9 C 7 Note: Before fixing blocks 15 into place it is important to ensure that the slot and groove of parts 7 and 9 are fully pushed together and lined up correctly at the top and bottom. b: Place blocks C 15 No! Yes! Attention: correct position. 9 15 9 7 15 15 between the two marks as shown.
Assembly Instructions Step 3 F Fitting Metal dowels. F F Screw metal dowels F into right side panel 7 , left side panel 8 and top panel 1 . 8 F F F Note: Insert metal dowels as far as shown. 7 F Do not over tighten. F F F F 1 Step 4 A Insert dowels A into the indicated parts.
Assembly Instructions Step 5 Note: The hole position. Fit shelf 5 into the holes on inside panels 4 . Important! Panels must be positioned as shown in the picture. 4 5 4 5 Step 6 Fixing base panel. With help, fit inside panels 4 to the base panel 2 then fix it using screws D . 4 Do not over tighten screws.
Assembly Instructions Step 7 Insert front frames 3 into the holes on right side panel 7 . 7 3 3 Step 8 Fixing base panel. With help, fit base panel 2 to the right side panel. Insert 2 locking nuts G into base panel where shown. Use a screwdriver to turn locking nuts G clockwise to lock. 7 G 2 G Do not over tighten.
Assembly Instructions Step 9 Fixing right side panel. With help, place left side panel 8 properly ensuring dowels and front frames are all fit into their holes at the same time. Insert 2 locking nuts G into base panel where shown. Use a screwdriver to turn locking nuts G clockwise to lock. 8 G Do not over tighten. G G G Step 10 Fix metal bracket L in the base panel 2 and bottom front frame 3 using screws B as shown.
Assembly Instructions Step 11 Fixing top panel. Important: With help, carefully turn the product upside down on top of panel 1 . G Insert 10 locking nuts G into the panels shown. Use a screwdriver to turn locking nuts G clockwise to lock. G G G Do not over tighten. 1 G G With help, stand the product upright. G G G Step 12 Fitting hinges to doors. Attach hinges H in the pre marked holes on doors 6 using screws B as shown.
Assembly Instructions Step 13 a: b: Hanging doors. 6 View from behind M a: With help, centralise the doors in the opening of the cabinet using the door spacer M to ensure correct spacing, as shown. B b: From inside the cabinet fix hinges using screws B as shown. 6 Note: To ensure the alignment of the doors is correct, centralise the doors in the opening before attaching to the cabinet. Step 14 Hinge adjustment.
Assembly Instructions Step 15 Fitting door lock. a: Screw clip J B in place using screws . Ensure that the 2 small wheels are flush with the edge of the base as shown in the diagram. b: Insert plug 6 K into J clip , ensuring they are leveled as shown in the diagram. J 2 6 K J c: Push the door against plug K . This will make 2 small marks on the door as shown in the diagram. K a: J d: The door can then be opened and plug K can be screwed into place using the 2 marks made as a guide.
Assembly Instructions Step 17 Fixing back panel. a: Important: Cabinet MUST be ‘square’ when back panels are attached. With help, turn cabinet upside down. N a: Slide large back panel 13 within grooves and then attach it using nails N . 13 b: Place small back N b: panels 14 within grooves and then attach using nails N . N 14 N 14 Attention: N N N N Assembly is complete.
Your 1 Year Guarantee Peace Of Mind Knowing Your Furniture Is Protected Protection received within the Manufacturer’s Guarantee Optional Added Protection with Furniture Care Covers you for manufacturing defects for 1 year. Covers you for up to 2 years for specific structural defects following the expiry of the manufacturer’s guarantee. he event of a problem within this time please call 0345 640 0800, or visit an Argos store. Please retain your receipt and order number as proof of purchase.
