05W PALM SANDER INSTRUCTION MANUAL PGF105P
Original instructions GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. 1) Work area safety a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Original instructions connected and properly used. Use of dust collection can reduce dust-related hazards. 4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
Original instructions to avoid hidden power cables and pipes. 11. After long working periods external metal parts and accessories could be hot. 12. If possible, ensure the work-piece is firmly clamped to prevent movement. 13. Your sander is a hand held tool, do not clamp your sander. 14. Before sanding, check the area is free of nails, screws, etc. 15. Never stop the sander by applying a force to the base plate. 16. Only use paper in good condition. Do not use torn or worn paper. 17.
OrIgINaL INstructIONs 1 2 5 4 3 cOMPONENt LIst 1. Handle 2. On/off switch 3. Sanding pad 4. Sanding paper 5. Vacuum adaptor accEssOrIEs 1pc 2pcs 2pcs 1pc Vacuum adaptor 32mm 60grit sanding papers 80grit sanding papers 100grit sanding paper We recommend that you purchase your accessories from the same store that sold you the tool. Use good quality accessories marked with a well-known brand name. Choose the type according to the work you intend to undertake.
TECHNICAL DATA Original instructions 230-240V~50Hz 105W 13000min-1 140x140x80mm 1.4mm /II 0.9kg Voltage Power input No load speed Diameter of base Orbital dia Protection class Machine weight NOISE INFORMATION A weighted sound pressure A weighted sound power KPA & KWA Wear ear protection when sound pressure is over LPA:81dB(A) LWA:92dB(A) 3.0dB(A) 85dB(A) VIBRATION INFORMATION Vibration total values (triax vector sum) determined according to EN 60745: Vibration emission value ah = 2.
Original instructions OPERATING INSTRUCTIONS 3. OPERATING THE SWITCH (See Fig C) NOTE: Before using the tool, read the instruction book carefully. 1. FITTING THE SANDING PAPER (See Fig A) 2 Fig.C To operate the sander, plug into mains (make sure switch is in switch off position first). Grip sander firmly and switch on. Depress the switch (2) to start or stop your palm sander. Fig.A Fit the paper over the pad so that it covers the entire area.
Original instructions 3. Different types of sanding paper will allow the sander to meet various needs. Different grades of sanding paper are available, the higher grit number, the finer the grit. For rough work start with a low grit (i.e. 80 grit) and change to a higher, finer grit (i.e. 100 grit or 120 grit) for finishing. If you use a fine grit for rough surfaces it will soon clog and need changing. 4.
Original instructions PLUG REPLACEMENT Your Power Tool is supplied with a fitted plug, however if you need to fit a new plug follow the instruction below.
ENVIRONMENTAL PROTECTION Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. If faults can not be remedied, contact the Helpline on 08448012949 GUARANTEE This product is selected for DOMESTIC USE ONLY and not for business use.
