4Ch H.264 Hardware Codec H.264 Network DVR User’s Manual VER 1.
4Ch H.264 hardware codec - Network DVR Installation & Safeguards INSTALLATION & SAFEGUARDS All the safety and operating instructions should be read before the unit is operated. Environment Condition for Installation 1. To prevent electric shock or other hazard, do not expose units to rain, moisture, or dust. 2. Place this unit in a well-ventilated place and do not place heat-generating objects on this unit. 3.
4Ch H.264 hardware codec - Network DVR Contents Contents CHAP. 1 Features & Package Contents ---------------------------------------------------------------- 4 1-1. Features ---------------------------------------------------------------- 4 1-2. Package Contents ---------------------------------------------------------------- 5 Function of Each Button ---------------------------------------------------------------- 6 2-1.
Ch H.264 hardware codec - Network DVR Contents Contents 5-3.
4Ch H.264 hardware codec - Network DVR CHAP 1. Features & Package Contents CHAP 1. Features & Package Contents 1-1.
4Ch H.264 hardware codec - Network DVR CHAP 1. Features & Package Contents 1-2. Package Contents NETWORK DVR POWER HDD ACTIVE USB 2. Remote Controller 1. DVR Main Unit 3. Power Cable 6. Software CD 4. Power Adapter 5. User’s Manual 7. Rubber Pad 8. HDD absorber 9. HDD Bolts Package Contents 10. Mouse Description 1. DVR Main Unit Stand-Alone Digital Video Recorder 2. Remote Controller Remote controller 3. Power Cable AC power supply to adapters for 12V DC power 4.
4Ch H.264 hardware codec - Network DVR CHAP 2. Function of Each Button CHAP 2. Function of Each Button 2-1. Front 2 1 Name Function ① USB HOST Used for Data Backup and Firmware Update (Only USB memory stick should be used.
4Ch H.264 hardware codec - Network DVR CHAP 2. Parts name & functions 2-2. Rear 1 2 3 4 5 6 FUNCTION CH 1 CAUTION CH2 MONITOR AUDIO RISK O F ELECTRIC SHO CK . DO NO T O PEN ! CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK. DO NOT OPEN COVERS . NO USER SERVICEABLE PARTS INSIDE .REFER SERVICING TO QUALIFIED SERVICE PERSO NNEL . IN WARNNIG : TO PREVENT FIRE OR SHOCK HAZARD. DO NOT EXPOSE UNITS NOT SPECIFICALLY DESIGNED FOR OUTDOOR USE TO RAIN OR MOISTURE.
4Ch H.264 hardware codec - Network DVR CHAP.3 Installation 3-1. Installation configuration 8 CHAP.
4Ch H.264 hardware codec - Network DVR CHAP. 3 Installation 3-1. Installation 1) HDD MAIN BOARD HDD 1. Connect Main Board and HDD using SATA data cable and HDD power cable. 2. Stick the HDD absorber (included in package) on the bottom of case and then install the HDD on top of them by using the bolts (included in package). 3. Screws must be inserted from outside of the case bottom. 2) Camera Connect camera to the camera input on rear panel of DVR marked CAMERA IN.
4Ch H.264 hardware codec - Network DVR CHAP. 3 Installation 3) Monitor Connect the video output marked MONITOR to Video-In of Main monitor.
4Ch H.264 hardware codec - Network DVR 5) Other External Device AUDIO IN OUT ETHERNET RS-485 : Controls external device like PTZ camera. (Pin No.1 & No.2) RELAY Output : Relay Output (Pin No.3 & No.5). SENSOR Input : Sensor Input – Alarm Input (Pin No.6 ~ No.10). ETHERNET: Connection to LAN, WAN Audio Input: Connection to a microphone Audio Output: Connection to a speaker VGA : Connection to CRT or TFT LCD monitor (D-SUB) 11 CHAP.
4Ch H.264 hardware codec - Network DVR CHAP. 4 Operation 4-1. System Log-In GENERAL USE OF MOUSE Mouse buttons Mouse Wheel Functions Increases or decreases setup value on the Menu mode Right Decreases setup value on the Menu mode Left Increases setup value on the Menu mode Execute all of the functions (clicking icons) * Please use a mouse pad for proper operation of the mouse. 1) After power on, a right-click of the mouse shows an icon bar on the screen. Then click the [Menu] icon to log in.
4Ch H.264 hardware codec - Network DVR CHAP. 4 Operation 1) HDD Clear You can see HDD Model name, serial number, number of blocks and size of HDD. In order to clear HDD, click ‘CLEAR’ at the bottom as shown below. (1) Please refer to 4-1. System Log in again. (2) Click ‘EXTERNAL DEVICE’. Then, click ‘ENTER’.
4Ch H.264 hardware codec - Network DVR CHAP. 4 Operation 2) Factory Default Factory default setting initializes DVR system. (1) Please refer to 4-1. System Log in again. (2) Click ‘FACTORY DEFAULT’. Then, click ‘ENTER’. DVR LOG-IN MAIN MENU USER ID USER PW 1 2 DISPLAY SETUP RECORD CONFIGURATION EXTERNAL DEVICE BACK-UP FIRMWARE UPGRADE FACTORY DEFAULT ADMIN ________ 3 4 5 6 7 8 9 LANGUAGE ENTER ENGLISH EXIT EXIT (4) Choose ON for ‘ALL’. (2) Click ‘DEFAULT’.
4Ch H.264 hardware codec - Network DVR CHAP. 4 Operation 4-3.
4Ch H.264 hardware codec - Network DVR CHAP. 4 Operation 4-4. Live View Setup 1) Full / Multiple View CHAP. 4 사용방법 Move the cursor onto [4 - split icon] in the icon bar and click it to view 4 channel division. To enlarge each channel, click 1,2,3,4 Icon. Then, you will see a channel in full screen mode. Full Screen Full Screen 2) SEQ Click ‘SEQ’ icon . It automatically displays full screen images in sequence. You can setup SEQ time interval on setup menu.
4Ch H.264 hardware codec - Network DVR CHAP. 4 Operation 4-5. Record It basically records as a setting made in Schedule Record mode except for emergency record mode. - Emergency Record Once you click this icon , it keeps recording continuously regardless of schedule setting. - Schedule Record (Continuous, Motion, Alarm and Motion/Alarm) Go to MAIN MENU-> RECORD -> SCHEDULE SETUP and setup schedule as you want. It records as a setting. - Record Icon in Red indicates Emergency Record and Schedule Record.
4Ch H.264 hardware codec - Network DVR CHAP. 4 Operation 4-7. Search There are three search methods controlled by a mouse wheel button, left and right button of a mouse. When you click [SEARCH] icon , then you see a window shown as below. Select a target data by using the mouse. In PERCENT SEARCH Mode, you can select certain data by clicking on the bar. To move to the previous mode, click ‘ESC’. 1. PERCENT SEARCH Search by percentage of total recorded data.
4Ch H.264 hardware codec - Network DVR CHAP. 4 Operation 4-8. PAN/TILT/ZOOM Camera Operation Click [PTZ] icon in the icon bar, then you can see ‘arrow’ keys & ‘+/-’ key shown below. Click these arrow keys to move a PTZ camera to each direction. By using ‘+/-’ key, you can control ZOON IN/OUT function. (‘+’ : ZOOM IN / ‘-” : ZOOM OUT) 4-9. Data Backup Right-click to see the icon bar and click [MENU] icon and go to ‘Backup’. (1) Please refer to 4-1. System Log in again. (2) Click ‘BACK-UP’.
4Ch H.264 hardware codec - Network DVR CHAP. 4 Operation (4) To set start time of back-up and back-up data size in MEDIA sub-menu, use the mouse (left/right/wheel button). ※ End time of back-up will be calculated automatically as per start time & date and the back-up data size you set. ※ You can select the back-up data size (size of back-up data from start of back-up), but END of back-up time is automatically determined by DVR itself. (5) Click ‘Back-up’ to start USB back-up.
4Ch H.264 hardware codec - Network DVR CHAP 5. Setup 5-1. General Operation Click the [MENU] icon and input user password to log in. (1) Please refer to 4-1. System Log in again. Then, click ‘ENTER’. DVR LOG-IN USER ID USER PW 1 2 ADMIN ________ 3 4 5 6 ENTER 7 8 9 EXIT MAIN MENU DISPLAY SETUP RECORD CONFIGURATION EXTERNAL DEVICE BACK-UP FIRMWARE UPGRADE FACTORY DEFAULT LANGUAGE ENGLISH EXIT MAIN MENU 21 CHAP.
4Ch H.264 hardware codec - Network DVR CHAP. 5 Setup 5-2. Display Setup This is setup menu for display on the screen. If you click ‘DISPLAY SET UP’, then you change setting values for display as shown below. DISPLAY SETUP VGA SETUP SCREEN DISPLAY OSD SETUP ESC 1) VGA Setup VGA SETUP RESOLUTION 800 X 600 / 60Hz DEFAULT ESC VGA SETUP : Sets RESOLUTION for a VGA monitor (TFT LCD or CRT) as shown below. Default Resolution for VGA is 800x600.
4Ch H.264 hardware codec - Network DVR CHAP.
4Ch H.264 hardware codec - Network DVR CHAP. 5 Setup 5-3. Record This is the most important configuration of the DVR. When you select ‘RECORD SETUP’ in the main menu, you can see the window as shown below.
4Ch H.264 hardware codec - Network DVR CHAP. 5 Setup 2) Schedule Setup DVR system records in Schedule Recording mode. In Schedule Recording mode, you can choose four different types of recording modes and schedule by 2 hour interval from Sunday to Saturday. Default recording mode is continuous recording. Set Recording time interval for a day of the week (Time interval : by 2 hour ) and recording type.
4Ch H.264 hardware codec - Network DVR CHAP. 5 Setup 5-4. Configuration When you click ‘CONFIGURATION’ on the main menu, you can go to ‘CONFIGURATION’ menu as shown on the right. CONFIGURATION HDD MANAGEMENT CAMERA SETUP MOTION SETUP ALARM SETUP INTERVAL SETUP TIME/DATE SETUP PASSWORD SETUP BUZZER SETUP ESC 1) HDD Management You can see HDD Model name, serial number, number of blocks and size of HDD. You can also clear HDD. (While you are in this HDD MANAGEMENT Mode, DVR does NOT record.
4Ch H.264 hardware codec - Network DVR CHAP. 5 Setup 2) Time/Date Setup In this setup, you can select date/time of DVR system and display format. You can adjust values by using the mouse wheel or left/right button of the mouse. ※ For the first time installation, date/time setup must be completed first.
4Ch H.264 hardware codec - Network DVR CHAP. 5 Setup 4) Motion Setup MOTION SETUP CHANNEL CH1 SENSITIVITY 6 DURATION 05 SIZE 2 ALL-DEFAULT DEFAULT ESC MOTION SETUP: You can change values by mouse wheel and left/right button of the mouse. - SENSITIVITY: Adjust sensitivity of a movement. You can adjust level 1 ~ level 7. [DEFAULT : 6] - DURATION : Whenever motion is detected (set in Motion Recording mode), DVR records for a certain time from the point when motion is detected. (2 sec.~99 sec.
4Ch H.264 hardware codec - Network DVR CHAP. 5 Setup 5) Interval Setup See the switching time interval for SEQ or PIP function. (1 sec. ~99 sec. ） SEQUENCE SCREEN :Set the sequencing switch time interval in live full screen. INTERVAL SETUP SEQUENCE SCREEN 01 SEC PIP SCREEN 01 SEC EVENT UPDATE 600 SEC PIP SCREEN : Set the sequencing switch time interval of PIP window. DEFAULT ESC EVENT UPDATE : Set the minimum time interval of event to be listed on EVENT LIST.
4Ch H.264 hardware codec - Network DVR CHAP. 5 Setup 8) Buzzer Setup BUZZER SETUP You can select Buzzer OFF/ON on this setup menu. KEY TONE VIDEO LOSS ALARM ACTIVE MOTION DETECT ON ON ON ON DEFAULT ESC 5-5. External Device Setup Please refer to 4-1. System Log in again. Click ‘EXTERNAL DEVICE’ Then, click ‘ENTER’.
4Ch H.264 hardware codec - Network DVR CHAP. 5 Setup (1) IP Setup : IP SETUP MAC ADDRESS DHCP MODE Shows the network information assigned to the DVR unit. If the DHCP setup status is AUTOMATIC, you can set the IP port only. If the DHCP setup status is MANUAL, you must set all parameters. If IP port number is blocked, a network specialist’s advice is needed. IP PORT IP ADDRESS GATEWAY SUBNET 00-0A-A2-00-FD-63 MANUAL IP DETECT 50000 192.168.001.160 192.168.001.001 255.255.255.255 ESC A.
4Ch H.264 hardware codec - Network DVR CHAP. 5 Setup B. Dynamic IP PC ISP Internet Cable Modem (Dynamic IP) LAN DVR (Server) This contrasts with a Dynamic IP address, wherein an IP address is assigned to a computer, usually by a remote server which is acting as a Dynamic Host Configuration Protocol server. IP addresses assigned using DHCP may change depending on the addresses available in the set scope.
4Ch H.264 hardware codec - Network DVR CHAP. 5 Setup C. Dynamic IP of PPPoE (DSL) PC Router or Gateway (IP Share) DSL Modem (Dynamic IP) ISP DVR (Server) DVR doesn’t support DSL (PPPoE), user will need to set NETWORK with IP SHARE in order to access DVR remotely. At this time, user will need to port forward on DVR. Please contact IP SHARE Manufacturer if you need to know how to forward port.
4Ch H.264 hardware codec - Network DVR CHAP. 5 Setup If you are using a router, please setting up DMZ and Port Forwarding instructions below. [How to set DMZ] - Set DMZ as per router manual, if you want to connect a DVR by using one internet line. - Setting procedure and name of DMZ may be various from router manufacturers. - For more detail information, please refer to router manual. One example of how to set DMZ is shown below. 1) Access to your router.
4Ch H.264 hardware codec - Network DVR CHAP. 5 Setup D. Direct connect to DVR DVR (Server) PC When you try to connect to DVR directly, you must use DIRECT CABLE. a. PC’s TCP/IP Setting 1. For WindowsXP/2000, Click [start] – [Control Panel] click 2.
4Ch H.264 hardware codec - Network DVR 3. Right-button click [Local Area Connection] 4. Click ‘Properties’ [General] – [Internet Protocol (TCP/IP)] 36 CHAP.
4Ch H.264 hardware codec - Network DVR CHAP. 5 Setup 5. IP Address Setting IP Address : AAA.BBB.CCC.DDD AAA.BBB.CCC is identical with DVR’s setting DDD with DVR’s setting is not same Subnet mask must be 255.255.255.0 Default gateway is AAA.BBB.CCC.1 AAA.BBB.CCC is identical with HUB’s Address DNS Server is different in the country and ISP Supplier. When PC does not using internet, if it does not input, it is irrespective. Setting example b.
4Ch H.264 hardware codec - Network DVR CHAP. 5 Setup DDNS SETUP (2) DDNS Setup : DDNS ENABLE DNS SERVER INTERVAL Please refer to CH.8 DDNS Setup for more information. Refer to CH7-2 DDNS set up in DVR on page 53. OFF 192.168.063.
4Ch H.264 hardware codec - Network DVR CHAP.
4Ch H.264 hardware codec - Network DVR CHAP. 5 Setup 5-6. Firmware Upgrade When it comes to firmware upgrade, you may ask your local dealer. FIRMWARE UPGRADE CURRENT VER UPGRADE VER 9046 / V 0.35_08 FW1 Version FW2 Version CHECH USB UPGRADE ESC 5-7. Factory Default Factory default setting initializes DVR system. Select categories below that you want to initialize and choose ON. Then, click ‘Default’ button. In order to initialize all of the categories below, choose ON for ‘ALL’.
4Ch H.264 hardware codec - Network DVR CHAP 6. IRS CHAP 6. IRS (Integrated Remote Station) MAIN INTERFACE Exit IRS SETUP Inputs information for IRS network connection. DVR SETUP Changes DVR setting over a network. VIEWER Enables to show live image display. SEARCH Enables to search and show recorded image display. BACKUP Enables to back up recorded images in DVR to your PC. PLAYER Enables to play the backup images on your PC.
4Ch H.264 hardware codec - Network DVR CHAP 6. IRS 6-1. IRS Setup MANUAL DDNS Select “Manual” to input IP address and port number manually. Select “DDNS” to use IP address and port number that you already registered in DDNS server. (For more information about DDNS, please refer to page 54~59.) MEMBER ID NAME Input member ID that you registered in DDNS server. Input DVR name that you registered in DDNS server. ADDRESS PORT Input IP address manually. Input port number manually.
4Ch H.264 hardware codec - Network DVR 6-2. DVR Setup You can change some settings of DVR listed below over a network. (Alarm, Buzzer, Interval, Record Configuration, Record Schedule, Audio) MANUAL Input IP address and port number of DVR manually. ADDRESS Input IP address of DVR manually. PORT NUMBER Input port number of DVR manually. LOGIN ID PASSWORD Input DVR ID which has been set in DVR already. (Input ‘admin’.) Input password of DVR. CLOSE Click “CLOSE” to exit.
4Ch H.264 hardware codec - Network DVR CHAP 6. IRS 6-3. Viewer 1 2 3 5 6 1 2 4 DVR connection setup : Input network information to connect. (IP / PORT / ID / PW) System information : Displays connection status and operating information. 3 Screen display a) SCREEN DIVISION : Selects full screen mode or 4-split mode b) CHANNEL : Displays full screen for each channel. 4 Audio : Set Audio ON/OFF. 5 PTZ control : Controls PTZ camera remotely.
4Ch H.264 hardware codec - Network DVR CHAP 6. IRS 6-4. Search 1 2 3 4 a 8 b c d e 5 6 7 1 DVR connection setup : Input network information to connect. (IP / PORT / ID / PW) 2 Screen display a) SCREEN DIVISION : Selects full screen mode or 4-split mode b) CHANNEL : Displays full screen for each channel. 3 System information : Displays connection status and operating information. 4 Recorded data display : Displays start time & end time of recorded data.
4Ch H.264 hardware codec - Network DVR CHAP 6. IRS 6-5. Backup 1) To execute BACKUP, input IP Address & Port and click ‘Connect Test’ button. 2) After Connect Test is done, you can see ‘Success Connect Test!’ message. Then, click ‘lock’ button and click ‘Set Backup Time’ button. ※ Interface and functions of Backup are subject to change without prior notice.
4Ch H.264 hardware codec - Network DVR CHAP 6. IRS 3) Now you set ‘Start Backup Time’, ‘End Backup Time’, ‘Save File Path’, ‘File Size’ and click ‘Apply’. 4) After finishing time setting, click ‘Start Backup’ to start backup. Then, you can see the backup file on the path that you chose. ※ Interface and functions of Backup are subject to change without prior notice.
4Ch H.264 hardware codec - Network DVR CHAP 6. IRS 6-6. Player 1 2 3 a 8 7 b c d 4 e f g 5 6 1 Time display : Displays current time. 2 3 Recorded data display : Displays start time & end time of recorded data. Also, displays operating status during playback. Screen display a) SCREEN DIVISION : Selects full screen mode or 4-split mode b) CHANNEL : Displays full screen for each channel. 4 Audio : set Audio ON/OFF 5 Operation buttons I a) OPEN : Selects backup AM4 file.
4Ch H.264 hardware codec - Network DVR CHAP 6. IRS Image EDIT Click “EDIT” to go to image edit mode. 1 2 1 EDIT TOOL : User can adjust color tone of copied images using this buttons. - Contrast : make bright part of image brighter and dart part of image darker : To reduce light and shade, lower contrast a little. - Brightness : make an image brighter : make an image darker - Sharpness : gives sharp-edge effect - Blur : make an image soft - Operation buttons : saves data in JPEG file format.
4Ch H.264 hardware codec - Network DVR CHAP 6. IRS AVI SAVE Click “AVI SAVE” to go to AVI saving mode. 1 2 1 2 OPTION : Used to save data in AVI file format. CHANNEL : Selects channel FRAMERATE : Decides frames per second of data to be saved. SIZE : Decides the size of data to be saved automatically. START : Starts saving STOP : Stops saving. Once it is stopped, ‘C:₩WEB_BACKUP’ folder is opened automatically. AVI SAVE : Opens ‘Option’ setting to start AVI saving.
4Ch H.264 hardware codec - Network DVR CHAP 7. DDNS Web-server CHAP 7. DDNS Web-server 7-1. Registering DVR for DDNS (DDNS Web-server) 1) Please access www.h264ip.com and click Register Member ID. 2) Please click ‘DVR Add’ or ‘MY DVR Register’ to register DVR. ※ Interface and functions of DDNS service are subject to change without prior notice.
4Ch H.264 hardware codec - Network DVR CHAP 7. DDNS Web-server 3) Please click confirm after inputting DVR information (DVR Name and MAC Address only). Then, Click “Confirm” button. 4) Now, DVR is listed on DDNS web server without IP and Port number. ※ Interface and functions of DDNS service are subject to change without prior notice.
4Ch H.264 hardware codec - Network DVR CHAP 7. DDNS Web-server 7-2. DDNS set up in DVR * The following setting is a sample for a cable modem connected to DVR directly. 1) Go to Menu 2) Go to IP SETUP menu, if you set DHCP AUTOMATIC then it detects IP address automatically. IP SETUP MAC ADDRESS DHCP MODE 00-0A-A2-00-00-00 AUTOMATIC IP PORT IP ADDRESS GATEWAY SUBNET 50000 192 168 001 160 192 168 001 001 255 255 255 000 DEFAULT ESC 3) Go to the previous menu and click DDNS SETUP.
4Ch H.264 hardware codec - Network DVR CHAP 7. DDNS Web-server 4) Set DDNS ON/OFF ‘ON’. IP address which is assigned from DHCP server is automatically input on DNS SERVER. DDNS SETUP DDNS ENABLE DNS SERVER INTERVAL ON 168.126.063.001 D-00 H-00 M-20 REGISTER DDNS STATUS IP ADDRESS IP PORT REMAIN TIME LAST REGISTRATION DATE > WED. 12 JUL 2006 REGISTER OK 192.168.001.160 50000 D-00 H-00 M-20 09 : 21 : 36 GMT ESC 5) Go down to REGISTER and push ENTER button to renew IP registered on DDNS SERVER.
4Ch H.264 hardware codec - Network DVR CHAP 7. DDNS Web-server 6) Go to your computer again after you see “SUCCESS TO REGISTER DVR INFO” and then Click ‘refresh’ button. Then, DDNS server automatically catches your DVR’s IP address and Port number. Note. Before using Web-Viewer, please add www.h264ip.com on Trusted Sites at first installation as follows. (Tools -> Internet Options -> Security) ① ② ※ Interface and functions of DDNS service are subject to change without prior notice.
4Ch H.264 hardware codec ③ - Network DVR CHAP 7. DDNS Web-server ④ ⑤ Click ⑥ www.h264ip.
4Ch H.264 hardware codec - Network DVR CHAP 7. DDNS Web-server 7-3. Web program Some functions of IRS (Integrated Remote Station) such as Viewer, Search, Backup and Player are also available on the web. *If ActiveX control installation is required for the first time access, please click ‘Yes’. Click and input information needed for internet connection to DVR manually. Click these icons, then it connects to DVR automatically via DDNS server.
4Ch H.264 hardware codec - Network DVR CHAP 8. Specifications CHAP. 8 Specifications • H.264 Hardware Codec • Real time live display in all channels • Triplex ( Playback / Recording / Ethernet ) • Web monitoring • Easy control by Mouse • USB memory stick for data backup.
4Ch H.264 hardware codec - Network DVR CHAP 10. Remote Controller CHAP. 9 Remote Controller PTZ PTZ On/Off SEARCH Search Menu MENU Menu On/Off No function 1~4 Select Ch.
4Ch H.
4Ch H.
4Ch H.
4Ch H.
4Ch H.264 hardware codec - Network DVR 4Ch H.
