Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN Contents 1.0 General information on operating instructions................................................................................................ 3 2.0 Notes on possible dangers ................................................................................................................................ 3 2.1 Significance of symbols ....................................................................................
5.4 Electrical connection ....................................................................................................................................... 12 5.4.1 Wiring diagram ARI-PACO 1,6 D.................................................................................................................. 12 5.4.2 Wiring diagram ARI-PACO 1,6 Y .................................................................................................................. 12 5.4.3 Connection ARI-PACO ..............
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 1.0 General information on operating instructions These operating instructions provide information on mounting and maintaining the fittings. Please contact the supplier or the manufacturer in case of problems which cannot be solved by reference to the operating instructions. They are binding on the transport, storage, installation, start-up, operation, maintenance and repair.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 2.2 Explanatory notes on safety information In these Operating and Installation Instructions dangers, risks and items of safety information are highlighted to attract special attention. Information marked with the above symbol and “ATTENTION ! ” describe practices, a failure to comply with which can result in serious injury or danger of death for users or third parties or in material damage to the system or the environment.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 4.0 Description 4.1 Field of application Actuating or shut-off valves are operated with the ARI-PACO 0.85 linear actuators which have a linear nominal path of up to 30 mm and require a thrust force of 1,6 kN. The linear actuators are adjusted to the thrust forces denoted in the technical data. When delivered with the valve the linear actuator travel has been adjusted to the control path of the valves.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 4.3 Diagram 4.3.1 ARI-PACO 1,6 kN Fig. 1 4.3.1.1 Parts Pos.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 4.4 Technical data - Remarks Type ARI-PACO Thrust kN Travel max. mm 30 Control speed mm/sec. 0,15 Motor voltage ( ±10% ) Control signal (input) Feedback signal (output) Power consumption VA 1,6 D 230V - 50H 24V - 50Hz Three-step signal 0 - 10 V DC (invertable, max. 0,5 mA) -- 0 - 10 V DC (invertable, max. 5 mA) 8,0 11,5 Operation mode Enclosure 1,6 Y S3 50% cyclic duration factor IEC 60529 IP 54 Max.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 4.5 Dimensions Clearance required for removal of hood Fig.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 5.0 Installation ATTENTION ! - Work on electrical systems or equipment must only be carried out by qualified electricians or by trained individuals under the guidance and supervision of a qualified electrician in compliance with regional electrical safety requirements and regulations. - Valve mountings such as drives, handwheels, hoods must not be used to take external forces, e.g.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 5.2 Manual operation 5.2.1 ARI-PACO 1,6 kN ATTENTION ! - Since the hand wheel always turns during motor operation (running display), never use manual operation when the motor is running - danger of injury! For the manual operation, the black sliding switch above the housing must be switched to manual (refer to Fig. 3). press and turn 90° Fig.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 5.3 Assembly instructions to the mounting on valves If the valve is already mounted at the plant, care must be taken that before the drive is assembled, no pressure difference occurs in the valve body. If necessary, close shut-off slide valve or switch off pump. 5.3.1 Mounting von valve ARI-PACO 1,6 kN turning splint toothed lock washer Fig.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 5.4 Electrical connection 5.4.1 Wiring diagram ARI-PACO 1,6 D Standard Accessories DE Torque swittch POT Potentiometer M Motor C Capacitor Fig. 5 5.4.2 Wiring diagram ARI-PACO 1,6 Y Standard Accessories DE Torque swittch M Motor C Capacitor SRM Electronic positioner, Position indicator Fig.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN ATTENTION ! - When using low voltage installation (230 V AC), the installation has to designed acc. to the requirements of protection class I ! The wiring to the PE terminal must be connected between clamping yoke and square washer (cupal washer). Please note, that the copper coated side shows to the clamping yoke. Copper-side of the square washer (Cupal washer) Bild 7 5.4.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 5.4.3.1 ARI-PACO 1,6 D - Connect the ground line of the connection lead to connector 1 of the connection strip of the linear actuators - Connect the impulse lead for the extended thrust rod on connector 2 of the connection strip terminal. - Connect the impulse lead for the retracted thrust rod on connector 3 of the connection strip terminal.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 5.5.2 Additional switching module in the ARI-PACO 1,6 D Additional switching module in the actuating drive ARI-PACO 1,6 D for feedback of the two valve positions. Both limit switches (torque switch), DE3 and DE4 switch parallel to the torque switches DE1 and DE2. Contact switches in the upper end position from 41-42 to 41-44 Contact switches in the lower end position from 61-62 to 61-64 Fig. 8 5.5.2.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN - Mount limit switch and secure with securing rings - upper limit switch attached to connector 61, 62, and 64, - lower limit switch attached to connector 41, 42, and 44. - Clamping strip and terminal strip shield are screwed on with self-tapping screws. - After mounting, secure the cable connector from the clamping strip to the end switches with cable ties. Do not run cables near moving parts or endangered locations.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 5.5.3 Potentiometer im ARI-PACO 1,6 D ATTENTION ! - Carry out insertion only on a linear actuator switched to a voltage-free state! (mains voltage switched off and secured against being accidentally switched on) . Parts 2 pcs. Studding bolt 2 pcs. Screws 2 pcs. Washers 1 pcs. Cable ties 1 pcs. Module Potentiometer ( pre-assembled ) consisting of: 1 transmission set 1 potentiometer 1 cable set 5.5.3.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 6.0 Putting the actuator into operation - Actuator components which rotate or move during operation. Crushing or injury hazard! Before putting a new plant into operation or restarting a plant after repairs or modification, always make sure that: - all works has been completed! - Regional safety instructions must be observed as a matter of policy. - hood of thrust actuator assembled. 6.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 6.2 Putting the actuator into operation ARI-PACO 1,6 Y ATTENTION ! - Before commissioning, check the correct insertion of the valves, as well as the electrical connection. If an adaptation of the actuating signals Y on the mounted valve is required, the adjustment can be carried through in following steps: 1. Remove servodrive housing.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 12. Adjust actuating directions switch according to valve function to (+) or (-) (in some cases, an inverted direction of action is required). 13. Reinstall housing and release the black button for manual actuating. 14. Execute function tests. 7.0 Care and maintenance The linear actuator requires little maintenance, so that no maintenance is required at fixed time intervals.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 9.0 Troubleshooting table ATTENTION ! - read point 10.0 and 11.0 prior to dismantling and repair work! - read point 6.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 10.0 Dismantlement of thrust actuator ATTENTION ! - The supply line for connecting up the thrust actuator must be in the dead state i.e. disconnected while dismantlement work is being carried out. After being disconnected, the mains power must be prevented from being switched back on again accidentally.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 11.0 Warranty / Guarantee The extent and period of warranty cover are specified in the "Standard Terms and Conditions of Albert Richter GmbH & Co. KG“ valid at the time of delivery or, by way of departure, in the contract of sale itself. We guarantee freedom of faults in compliance with state-of-the-art technology and the confirmed application.
Operating and installation instructions Electric thrust actuator ARI-PACO 1,6 kN 12.0 EC declaration of conformity EC declaration of conformity as defined by Directive about electromagnetic compatibility 2004/108/EEC and the EG-Low voltage directive 2006/95/EEC Herewith we declare, ARI-Armaturen Albert Richter GmbH & Co.
