SNOW BLOWER by Owner’s Manual This manual contains important safety instructions for the gasoline engine powered snow blower models: 30SB, 36SB, 45SB READ SAFETY WARNINGS AND OPERATING INSTRUCTIONS CAREFULLY. SAVE THIS MANUAL. Need Help? Parts, Service, and Technical Assistance call: (919)-550-3221 Monday-Friday 8:00AM-5PM EST www.beastpowerequipment.
Snow BEAST 30SB, 36SB, 45SB Copyright© 2012 by GXi Outdoor Power, LLC. All rights reserved. No part of this publication can be reproduced or distributed without prior written permission of GXi Outdoor Power, LLC Clayton, NC 27520 USA. DEK is a registered trademark of GXi Outdoor Power, LLC GXi Outdoor Power, LLC reserves the right to discontinue or change specifications or design at any time without notice and without incurring any obligation whatsoever.
BEAST SERIES Check out our other great products at www.HomeDepot.com or visit our web site at www.beastpowerequipment.
Snow BEAST 30SB, 36SB, 45SB Contents Safety Information and Warnings ......................................................................... 1 Preparation Safety Precautions ............................................................................2 Operation Safety Precautions ................................................................................3 Safety Decals ...........................................................................................................
Snow BEAST Safety Information and Warnings Safety Information Emission Control System Information 30SB, 36SB, 45SB Training The U.S. and California Clean Air Acts EPA and California regulations require all manufacturers to furnish written instructions describing the operation and maintenance of emission control systems. The following instructions and procedures must be followed in order to keep the emissions from your engine within the emission standards.
Snow BEAST Preparation Safety Precautions Preparation—Safety Precautions 1. Inspect the area where the equipment is to be used and remove all objects such as rocks, mats, and wire which can be thrown by the machine causing serious injury or death. 2. Disengage all clutches and shift to neutral before starting the engine. 3. Disengage all control levers before starting the engine. 4.
Snow BEAST Operation Safety Precautions Equipment Operation—Safety Precautions 1. Do not operate the engine in a confined space where dangerous carbon monoxide fumes can collect. Carbon monoxide is odorless, tasteless, and can be fatal. 2. Never operate the snow blower without good visibility or light. 3. Exercise extreme caution when operating on or crossing gravel drives, walks, or roads. Stay alert for hidden hazards or traffic. 4.
Snow BEAST Operation Safety Precautions Clearing A Clogged Chute—Safety Precautions 1. SHUT THE ENGINE OFF! 30SB, 36SB, 45SB Do NOT over-prime the engine. Pressing the primer bulb more than 3x could result in flooding the carburetor making the engine hard to start or cause fuel to leak from the carburetor inlet. 2. Wait at least 10 seconds to be sure the augers have stopped rotating. 3. Always use a cleanout tool and never your hands. 4.
Snow BEAST Safety Decals 30SB, 36SB, 45SB Safety Decal Identification The labels shown below are located on your snow blower to warn you of potential hazards and provide you with important safety information. If these decals become difficult to read or are missing from the snow blower, please contact GXi Parts & Service, LLC at (919)-550-3221 or www.beastpowerequipment.com for a replacement. V8.10.25.
Snow BEAST Feature Product Type Clearing Path Engine Torque Engine Start Speed Control Deck Type Discharge distance Impeller Auger Discharge Chute Fuel/Capacity Chute control Product Specifications 30SB Snowblower 30” 302cc 15.9 ft.lbs 120V Electric Start and recoil 6 fwd, 2 rev All Steel 40’ 16” 2 Stage 16” serrated 6” Unleaded gasoline/1.32 GAL Crank Models 36SB Snow blower 36” 420cc 20.7 ft.lbs 120V Electric Start and Recoil 6 fwd, 2 rev All Steel 40’ 16” 2 Stage 16” serrated 6” Unleaded gasoline/1.
Snow BEAST 30SB, 36SB, 45SB Control Panel and Snow Blower Components Throughout this manual, instructions are given on the operation of your SNOW BEAST snow blower. We recommend that while going through this manual, you have your snow blower available for quick and easy access in order to orient yourself with the controls, maintenance and orientation of different parts. Please read through the manual before operating. Control Panel Below is a diagram of the control panel.
Snow BEAST Missing Parts Request Form 30SB, 36SB, 45SB Please indicate the part that you are missing: Name Hardware bag Other Address Date of purchase Model #: Phone Email Serial #: Comments: IMPORTANT: Please include your receipt. Without a receipt, your order will be delayed. You may also email us at: customerservice@gxioutdoorpower.com Fax: (919)-550-3277 If emailing, please scan in your proof of purchase. Please refer to pages 26-30 for a detailed parts listing and description.
Snow BEAST Assembly Instructions 30SB, 36SB, 45SB Step 1: Control Panel Handles 1. Align the two holes on each side of the control panel handles over the lower handle frame. 2. Insert the bolts through the handlebar holes and frame holes. Secure in place with hardware provided. All bolt heads must face to the inside. Step 2: Directional Discharge Chute 1. Fit round spacer onto impeller housing before installing chute. Apply light coat of grease onto spacer. 2.
Snow BEAST Assembly Instructions 30SB, 36SB, 45SB Step 3: Chute Rotation Cable Connection (continued) 1. Locate the connection: The chute rotation cable connection is located at the base of the discharge chute between the engine and the discharge chute. 2. Slide the threaded end of the connector down the cable in order to easily see the end of the cable connection. The center section should be about 3/4” to 1” beyond the end of the cable.
Snow BEAST 30SB, 36SB, 45SB Step 4: Chute Direction Control Cable Support With the rubber lined one hole strap removed, put the chute direction control cable and the chute deflector cable into the opening, and press the strap together aligning the hole for the bolt. Secure strap to side of the engine. NOTE: Rotate discharge chute and ensure there is no binding of any cables and there is enough slack in the deflector cable for full rotation. Step 5: Drift Cutters (if desired) 1.
Snow BEAST Assembly Instructions 30SB, 36SB, 45SB Step 7: Auger and Transmission Control Cables Control cables are preset at the factory, but may require additional adjustment for optimal operation. Control cables require periodic inspection and maintenance to maintain optimal performance. 1. Locate the black cable on the right side (standing from the operator position) of the snow blower. Ensure the cable is properly seated in the plastic guide pulley at the rear of the chassis. 2.
Snow BEAST Assembly Instructions 30SB, 36SB, 45SB Step 9: Headlight 1. Connect snow blower headlight wire plug to the headlight bulb. 2. Connect the headlight bezel to the control panel. A. Tilt headlight assembly and align tabs on the top of the headlight bezel with the notches in the control panel. Insert the notches into the panel. B. Tilt headlight assembly down while gently squeezing the headlight bezel and push headlight into control panel. Step 10: Filling Oil and Gasoline 1.
Snow BEAST Starting the Engine 30SB, 36SB, 45SB WARNING DANGER Before attempting to use your snow blower, make sure you are familiar with all of the components and have read the manual. DANGER: Exhaust contains poisonous carbon monoxide, a colorless and odorless gas. Breathing exhaust can cause loss of consciousness and may lead to death. Do not operate the engine in a confined space where dangerous carbon monoxide fumes can collect.
Snow BEAST Operating Instructions 30SB, 36SB, 45SB Transmission Control Engage Transmission Drive Your snow blower is equipped with an easily adjustable transmission control, which can be adjusted for forward and reverse speed. To engage the transmission drive squeeze the right lever to the hand grip. To disengage, let go of the right lever. There are six forward and two reverse speeds. To change the speed, pull the handle out to the right and move the handle to the desired speed.
Snow BEAST Operating Instructions 30SB, 36SB, 45SB Chute Direction Control Headlights To rotate the chute to the right rotate the chute control clockwise. To turn on the lights, flip the switch up. To turn off the lights, flip the switch down. To rotate the chute to the left rotate the chute control counter-clockwise. Never use your hands to clean a clogged chute or opening. Chute Discharge Angle There are five different angles the discharge chute can be arranged to discharge.
Snow BEAST Operating Instructions 30SB, 36SB, 45SB Using your Snow Beast. The following tips will help ensure proper and long lasting use of your BEAST snow blower. ALWAYS wear proper safety equipment when operating the snow-blower, and make sure you dress appropriately for cold weather. Figure 1 Figure 1 Before use, always ensure there is nothing lodged in the auger, or impeller area.
Snow BEAST General Maintenance The Importance of Maintenance CAUTION Regular maintenance is essential to ensure your snow blower continues to deliver safe and high-quality performance. To help you properly care for your snow blower, the following pages include a recommended maintenance schedule, routine inspection procedures, and simple maintenance procedures using basic hand tools. Maintenance is the responsibility of the owner and must be performed regularly.
Snow BEAST 30SB, 36SB, 45SB Maintenance Schedule Time Interval Item Procedure Belts Inspect Tension (adjust if needed) Augers/Impeller Inspect Engine Air Filter Inspect Break-in (first 5 hrs) X Every 8 hrs Every 40 hrs Every 100 hrs Every 200 hrs (daily) (weekly) (Bi-weekly) (monthly) X X X Check X Engine Oil Change 20-30 hrs Engine Spark Plug Inspect 20-30 hrs Fuel Line Check Hardware Check for proper tightness Snow Blower Main Frame Remove debris from under belt cover Safety Int
Snow BEAST Service Adjustments 30SB, 36SB, 45SB Adjusting Augers/Impeller Cable Adjusting Drive Cable If tension seems to be too loose or too tight the augers/impeller cables needs to be readjusted. If tension seems to be too loose or too tight the drive cables needs to be readjusted. 1. Loosen the bolt above where the cable screws in to the left side of the control panel. 2. Loosening the bolt enables the cable to screw in further, which makes the augers/impeller handle tighter. 3.
Snow BEAST Service Adjustments Check & Replacing the Transmission Drive Belt If belt needs to be changed or altered for any reason, the belt is located in the front of the snow blower behind the discharge chute and in front of the wheels. 1. Remove the cover that is protecting the snow blower’s belts. Remove the screws and simply lift up the cover. 2. Remove the black belt and replace with a new belt. 3. Attach the cover and all hardware as they were when taken off.
Snow BEAST Service Adjustments Adjusting Discharge Deflector The discharge chute is preset at the factory, but may require adjustment over time or during maintenance. For adjustments, follow the procedure below: 1. Loosen the two nuts at the chute cable mount on the discharge chute. 2. To make the chute open more, adjust nuts so the cable end moves closer to the discharge deflector (upward). 3. To make the chute close more, adjust nuts so the cable end moves further from the discharge deflector (downward).
Snow BEAST Storage Instructions 30SB, 36SB, 45SB Short Term Storage Let engine cool before storing and do not store near flame, high heat, and possible ignitions from sparks. Do not drain fuel indoors or near a flame. Always park machine on level ground. Always clean off all flammable material as well as grime and dirt before storage. Store the machine in a clean and dry environment. Wash with mild detergent and water only.
Snow BEAST Troubleshooting 30SB, 36SB, 45SB Problem Possible Causes Solution Engine will not start 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Fuel is leaking from the engine. 1. Primer button was pressed too many 1. Do not press primer more than 3 times. Wipe off times. excess fuel and allow to dry COMPLETELY before attempting to start 2. Fuel hose has become dis-connected 2. Re-connect fuel hose and clamp(s) 3. Carburetor has contaminants in it 3.
Snow BEAST Troubleshooting 30SB, 36SB, 45SB Problem Possible Causes Solution Snow blower will not move forward or reverse 1. Transmission cable out of adjustment (too loose) or damaged. 2. Friction wheel rubber worn 1. Readjust transmission cable If damaged, replace and readjust. 2. Replace friction wheel assembly Cannot move snow 1. Transmission handle is pressed 1. Release transmission handle blower when the engine is into the engaged position off 2. Transmission cable out of 2.
Snow BEAST 30SB, 36SB, 45SB 30SB Collector Assembly Diagram Key - Year Model 2012/13 Item # GXi Part Number 1 B00512 2 3 4 B00712 B00910 B01412 5 B01512 6 B02410 7 B03712 8 B04812 9 B05112 10 B06511 Discharge chute assembly, SB orange, with labels, hand guard, hand guard spring, deflector, deflector seal, plastic rotation ring, chute mounts and spacers, deflector cable, and hardware Discharge chute deflector, SB orange, with deflector seal and hardware Drift cutters, set of 2, SB orange,
Snow BEAST 30SB, 36SB, 45SB 36S B Co llec tor A sse m bly D iag ra m K ey - Ye ar M ode l 2012/13 Item # G X i P art N um b er 1 B00512 2 3 4 B00712 B00910 B01412 5 B01512 6 B02410 7 B03712 8 B04812 9 B05112 10 B06511 11 B06811 12 B06912 13 B07111 14 B07212 15 16 17 18 19 B08211 B08311 B08911 B08112 B06711 V8.10.25.
Snow BEAST 30SB, 36SB, 45SB 45SB Collector A ssem bly D iagram Key - Year M odel 2012/13 Item # G Xi Part N um ber 1 B00512 2 3 4 B00712 B00910 B01412 5 B01512 6 B02410 7 B03712 8 B04812 9 B05112 10 B06511 11 B06811 12 B06912 13 B07111 14 B11012 15 16 17 18 19 B08211 B08411 B08911 B08112 B06711 V8.10.25.
Snow BEAST 30SB, 36SB, 45SB 30SB, 36SB, 45SB Chassis Assembly Reference Item # 30, 36, 45 SB Collector Assembly Diagram Key - Year Model 2012/13 GXi Part Description Number 1 2 3 B00112 B01110 B01312 4 B01910 5 B02010 6 B02212 7 8 B02510 B02610 9 B09012 10 B02812 11 B02912 12 B03412 13 B03512 14 B03811 15 B03911 16 B04412 17 B04511 V8.10.25.
Snow BEAST Replacement Parts 30SB, 36SB, 45SB To order replacement parts, visit our web-site at www.serviceandwarrantyonline.com Or dial Toll Free 1-800-393-0668 Monday-Friday 8AM-5PM OEM Replacement Parts Engine Parts GXi Part Number E10211 B01712 B09612 Fuel Primer Bulb Kit: Includes primer bulb assembly, fuel line, and 2 clamps. Models: 30SB, 30SS, 36SB, 36SS, 45SB, 45SS Fuel Tank with gas cap, fuel valve, fuel line, and clamps for 420cc Snow Blower Engine.
Snow BEAST Limited Warranty & Service 30SB, 36SB, 45SB Length of Warranty: *(from the date of original retail purchase) Products Covered by this Warranty Noncommercial/ Nonrental Commercial Rental Engine 24 months 90 days 90 days Transmission Snow blower 12 months 12 months 90 days 90 days 90 days 90 days *LENGTH OF WARRANTY: Batteries supplied with applicable products as standard, original equipment are covered by this warranty for a period of 90 days from the date of original retail product