Product Manual
Table Of Contents
- Welcome
- Safety
- Practices & Laws
- Emission Control System
- Required Operator Training
- Safety Alert Symbol
- Signal Words
- Safety Decals
- Safety Rules
- Assembly
- Required Tools
- Unpack Unit
- Assemble Steering Levers
- Secure Seat Cable
- Secure Operator Presence Cable
- Install Deck Lift Pedal
- Install Trailer Hitch
- Prepare Unit for Operation
- Controls and Features
- Ignition Key
- Choke Control Knob
- Throttle Control Lever
- Power-Take-Off (PTO) Knob
- Hour Meter
- Height-of-Cut Dial
- Deck Lift Pedal
- Seat Adjustment Lever
- Parking Brake Lever
- Safety Interlock System
- Steering Levers
- Transaxle Bypass Levers
- Anti-scalp Wheels
- Operation
- Emergency Stopping
- Before Operating Unit
- Start the Engine
- Operate Unit
- Stop the Engine
- Move Unit Manually
- Transport Unit
- Maintenance
- Maintenance Schedule
- Service Parts
- Hour / Maintenance Meter
- Check Safety Interlock System
- Check Parking Brake
- Check Engine Oil
- Check Tire Pressure
- Check Carbon Canister Filter
- Check Fasteners
- Lubricate Unit
- Maintenance Preparation
- Check Mower Blades
- Check Battery
- Check Mower Belts
- Hydraulic Fluid
- Adjustments
- Adjust Seat
- Adjust Steering Levers
- Adjust Unit to Track Straight
- Adjust Parking Brake Lever
- Remove and Install Mower Deck
- Adjust Mower Deck
- Storage
- Short-Term Storage
- Long-Term Storage
- Start-of-Season Preparation
- Accessories
- Troubleshooting
- Specifications
- Warr anty
EN - 2
Read these safety rules and follow them
closely. Failure to follow these rules could
lead to loss of control of unit, severe personal
injury or death to you or bystanders, or result
in damage to property or the machine.
PRACTICES & LAWS
Practice usual and customary safe working
precautions. Learn applicable rules and laws
in your area. Always follow the practices set
forth in this manual.
EMISSION CONTROL SYSTEM
This equipment and/or its engine may include
exhaust and evaporative emissions control
system components required to meet U.S.
Environmental Protection Agency (EPA)
and/or California Air Resources Board
(CARB) regulations. Tampering with emission
controls and components by unauthorized
personnel may result in severe fines or
penalties. Emission controls and components
can only be adjusted by an Ariens Company
dealer or an authorized engine
manufacturer's service center. Contact your
Ariens Company Equipment Retailer
concerning emission controls and component
questions.
REQUIRED OPERATOR
TRAINING
The original purchaser of this unit was
instructed by the seller on safe and proper
operation. If unit is to be used by someone
other than the original purchaser, loaned,
rented, or sold, ALWAYS provide this manual
and any needed safety training before
operation.
SAFETY ALERT SYMBOL
SIGNAL WORDS
The safety alert symbol above and signal
words below are used on decals and in this
manual. Read and understand all safety
messages.
1. Danger
2. Warning
3. Caution
4. Notice
NOTICE: Indicates information or procedures
that are considered important but not hazard
related. If not avoided property damage could
result.
5. Important
IMPORTANT: Indicates general reference
information worthy of special attention.
SAFETY
WARNING: AVOID INJURY.
This cutting machine is capable
of amputating hands and feet
and throwing objects. Failure to
observe the safety instructions
in the manuals and on decals
could result in serious injury or
death.
This is the safety alert symbol. It
means:
• ATTENTION!
• YOUR SAFETY IS
INVOLVED!
When you see this symbol:
• BECOME ALERT!
• OBEY THE MESSAGE!
DANGER: Indicates an
IMMINENTLY HAZARDOUS
SITUATION! If not avoided,
WILL RESULT in death or
serious injury.
WARNING: Indicates a
POTENTIALLY HAZARDOUS
SITUATION! If not avoided,
COULD RESULT in death or
serious injury.
CAUTION: Indicates a
POTENTIALLY HAZARDOUS
SITUATION! If not avoided, MAY
RESULT in minor or moderate in-
jury. It may also be used to alert
against unsafe practices.