Instruction Manual

ManualsBrandsAries Automotive ManualsFor the car200801-2

Page 1 of 5 4/15/2010)

PARTS LIST:

Qty Description Qty Description

1 Driver/Left Sidebar 3 Rive Nuts

1 Passenger/Right Sidebar 8 10mm x 35mm Hex Bolts

1 Driver/Left Front Mounting Bracket 8 10mm lock nuts

1 Passenger/Right Front Mounting Bracket 16 10mm Flat washers

1 Driver/Left Rear Mounting Bracket 4 8mm x 30mm Hex Bolts

1 Passenger/Right Rear Mounting Bracket 10 8mm Flat washers

1 Driver/Left Front Brace Bracket 6 8mm Lock washers

1 Passenger/Right Front Brace Bracket 4 8mm Nuts

2 C Bolts 2 25mm x shims

1 Rive nut tool

INSTALLATION INSTRUCTIONS

200801 / 200801-2

2009-2010 SUBARU FORRESTE

Passenge

Right

Side Rear

Mounting Bracket

Passenge

Right Side

Front

Mounting

Bracket

Drive

Left Side

Rear Mounting

Bracket

Drive

Left

Side Front

Mounting

Bracket

C Bolt

Rive Nut Tool

(Put together as is

laid out example)

Passenge

Right Side

Front Brace Bracket

Drive

Left Side

Front Brace

Bracket

Passenge

Right Side

Drive

Left

Side

Front

Summary of content (5 pages)

PAGE 1
INSTALLATION INSTRUCTIONS 200801 / 200801-2 2009-2010 SUBARU FORRESTER PARTS LIST: Qty 1 1 1 1 1 1 1 1 2 1 Description Driver/Left Sidebar Passenger/Right Sidebar Driver/Left Front Mounting Bracket Passenger/Right Front Mounting Bracket Driver/Left Rear Mounting Bracket Passenger/Right Rear Mounting Bracket Driver/Left Front Brace Bracket Passenger/Right Front Brace Bracket C Bolts Rive nut tool Qty 3 8 8 16 4 10 6 4 2 Passenger/ Right Side Description Rive Nuts 10mm x 35mm Hex Bolts 10mm lock nuts 10m
PAGE 2
PROCEDURE: 1. REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. 2.
PAGE 3
To protect your investment, wax this product after installing. Regular waxing is recommended to add a protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could damage the finish. For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild soap may be used also to clean the Sidebar. For gloss black finishes: Mild soap may be used to clean the Sidebar.
PAGE 4
Fig 4B Rive nut tool procedure (outside of hole) DO NOT COLLASPE RIVENUT OUTSIDE OF HOLE THIS VIEW BELOW IS ONLY TO SHOW PROCEEDURE OUTSIDE OF HOLE Rive nut With a wrench turn the large nut clock wise until rive nut is fully collapsed Place a wrench on the bolt so it does not turn while turning the nut above Place a wrench on the bolt so it does not turn while turning the nut above Nut Nut Place a wrench on the nut and turn it clock wise until it collapses the rive nut inside the hole Place a wren
PAGE 5
Fig 4C Brace bracket secured to mount bracket with (1) 8mm hex bolt (2) 8mm flat washer (1) 8mm lock washer (1) 8mm nut Fig 5 Rive nut installed Brace bracket secured to rive nut with (1) 8mm hex bolt (1) 8mm flat washer (1) 8mm lock washer Fig 6 Fig 7 Remove tow strap Rear mount bracket installed with factory bolts Fig 8 Front bracket Fig 8A Rear bracket Fig 9 Installation completed Brace bracket secured to mount bracket (1) 8mm hex bolt (2) 8mm flat washer (1) 8mm lock washer (1) 8mm nut At