Do not remove the cover or attempt to service this unit by yourself. You may void your warranty. Servicing of any nature should be performed only by an authorized technician. If any of the following occur, immediately unplug your monitor and call an authorized technician. » The power cord or plug is frayed or damaged. * Liquid has been spilled into the monitor, or it has been exposed to rain. + The monitor has been dropped or the case has been damaged. .
TABLE OF CONTENTS 1 INTRODUCTION. Plug & Unpacking... 2 INSTALLATION. Choosing A Workstation... ‘The Signal Cable Connection The AC Connection 3 OPERATION Tile & Swivel Adjustments Power Controls Adjustment 4 TECHNICAL SPECIFICATION; Specifications . 5 TROUBLE SHOOTING Power... Display 6 PANEL CRITERIA Conditions... Cosmetic Anomalies Inspection Specifications . Functional Anomalies Inspection Specification. 1 INTRODUCTION Congratulations on the purchase of your new 15.1" LCD Monitor.
2 INSTALLATION Choosing A Workstation ‘When choosing an appropriate workspace, keep these few things in mind: ® A sturdy, level surface. ® An electrical wall outlet and a telephone wall jack near the computer. ® At least 3-inch clearance at the back of the computer to allow for the required airflow. ® Do not place near a window. Exposing the Monitor to direct sunlight for extended periods may damage the unit. ® You may want to use a desk lamp to adjust the ambient lighting for your viewing comfort.
£1 tl P00) some aus Buyout) : p Andy “JIB JO 1200 Up OWN pus erm a Gang ‘pod pg op owr dep sp Sng» “TOJO SU3 JO TUT a1) uo Mod DI ay oye] onrush) HV NL,
3 OPERATION Tilt & Swivel Adjustments The monitor is capable of both tilt and swivel adjustments. +20° 5° Figure 6: Tilt Adjustment ® With the tilt feature, the monitor is capable of vertical adjustments of 20° to-5" . ® The swivel feature allows for upright position. Power Controls The power controls are located on the top side of the monitor’s front panel. Power Switch ® When the power switch is pressed, the monitor will be tuned on.
Low Radiation MPR II COSTCO (Option) TERR [Operating Temperature 0-407 Relative Humidity 10 ~ 50% non-condensing Dimension 402mm(W) x 397Tmm(H) x 172mm{D) Net Weight 6.2KGS {13.7LBS} 5 TROUBLE SHOOTING This section will try to anticipate potential problems that you may encounter the day-to-day use of your monitor. Included in this section is information w should help solve these problems for you.
Dirt: Product passes if dirt can be wiped off easily Following defect to be judged by Limit Samples when it is necessary a) Rainbow color (Newton ring) b Rubbing mark ¢) Mottling (Uniformity) 4d) Dim line (Vth shift line} Total number of cosmetic defect with the countable range Functional Anomalies Inspection Specification There should be no displays that are unable to show any image. Functional defect of pixels’ Definition 1) Each RGB element of a pixel is called sub pixel.
CARIES, INC. 3F, NO. 100, MIN-CHURN RD., SHIN SEN CITY, TAUPE! TAIWAN R.0.C. TEL : FAX : 886-2-22180673 FEDERAL COMMUNICATIONS COMMISSION FCC ID:NPUISTP Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA. Re: About the modification of LCD COLOR MONITOR Gentlemen: L, hereby, declare that all modification on the FCC ID: NPU15TP, will be added or layout on the mass production products. Modifications are shown as below: 1.
CARIES, INC. 3F, NO. 100, MIN-CHURN RD., SHIN SEN CITY, TAIPEI TAIWAN R.O.C. TEL : 886-2-22180883 Added gasket on I/O board cover. {As the photo No.8) Added cooper tapes near inverter board. (As the photo No.8) Added cooper tapes on two edges of panel. {As the photo No.18) Added a aluminum tape on gap of base metal sheet. (As the photo No.10) Added a aluminum tape beside 1/0 board. {As the photo No.10) Added two cooper tapes on ground wires of 1/0 board. (As the photo No.