Aristel Group AV-Series System Programming Manual
CONTENTS PROGRAMMING INITIALIZATION.................0-1 111 SLT Dial Tone Timeout ...................................................1-5 112 SLT Inter-Dialing Timeout ...............................................1-6 INTRODUCTION: .................................................................. 0-1 113 Transfer Busy Recall Timeout.........................................1-6 SYSTEM PROGRAMMING: .................................................... 0-1 114 Transfer No Answer Recall Timeout .......
135 136 The 2nd DSS Page Remaining Time or SLT MSG Wait 214 Automatic CO Search .....................................................2-5 Silence Time................................................................. 1-12 215 Dial_9 Capability.............................................................2-5 SOS Enable Delay Time or SLT MSG Wait Ringing 216 CO Delay Capability/Paging Tone of 15 Keys KP...........2-6 Time .............................................................................
241 Direct Intercom Dialing & FAC Uninhibited by Call Limit 306 Day Time Schedule ........................................................3-5 Duration Capability ....................................................... 2-16 307 SMDR Report .................................................................3-6 242 Exclusive Hold & System Wide CFW Capability........... 2-17 308 Midday Time ...................................................................3-7 243 SOS Outgoing-Playing Times...........
07 Station Function - General Function 3.......................... 5-12 508 Station Function - Hot Line ........................................... 5-13 509 Station Function - Individual SPD Block ....................... 5-14 510 ~ 599 Reserved For Future Use.............................. 5-15 CO FUNCTION (ZONE 600 ~ 699) ....................................... 6-1 600 Incoming Ringing Assignment - Day Time ..................... 6-1 601 Incoming Ringing Assignment - Night Time...................
INITIALIZATION Step 2. Programming Initialization Step 3. Introduction: There are six different programming zone groups contained in the system. This section details, in easy to follow instruction, the information necessary to program the system. Step 4. Step 5. System Programming: Access to the system programming zone is restricted to personnel with the "Programming Password".
INITIALIZATION 25 Buttons Key Telephone Function Keys During System Programming 15 Buttons Key Telephone Function Keys Function Illustration [DSS1] Back to the previous Program Zone [DSS2] Forward to the next Program Zone. [DSS3] Shifts cursor left. [DSS4] Shifts cursor right. [DSS5] Changes the Function Condition for the DSS key in Key Group Assignment. [DSS6] Help List. [DSS10] Clears all digits to be blank (or “d”) in the current zone area. [DSS11] Saves the setting data to the system memory.
INITIALIZATION Entering Programming Help List The Programming Help List is to help users review each programming zone if the zone function is forgotten or the Programming Manual is not available. During Help List the name of the zone and the programming status will be displayed on the LCD display for three (3) seconds before moving to the next zone number automatically. Step 1. On Hook. Step 2. Press [FUNC] + [#] + [DSS21] to enter Programming Help List. Step 3.
INITIALIZATION 101 DTMF Generation Time System Programming System Timing Parameter (Zone 100 ~ 199) Aristel TM 101 DTMF Time=055 (∗2ms) <-- Program Status Area 100 Pause Time Aristel <-- SSS=000~255 AV SERIES TM 100 Pause Time=020 (∗40ms) <-- Program Status Area Description: <-- SSS=000~255 DTMF Generation Time is the length of time needed to generate a Def.=020=20x40=800 ms DTMF signal for each outgoing dialing digit under DTMF or Tone (T) SSS=000~255 <-- AV SERIES Def.
INITIALIZATION maybe become a pulse digit. but greater than SLT Hold Time (Program Zone 103) the call will be put into Hold status automatically. Interrelation Zone: Program Zone 103 On Hook B or Hook-Flash B: The call will be held. On Hook C or Hook-Flash C: The call will be disconnected.
INITIALIZATION 105 When the internal station is engaged with a CO line, any other incoming Ring Off Time Aristel call through PSTN to the internal station on the same engaged CO line, TM the system can send a FLASH signal to the PSTN as soon as the 105 Ring Off Time=004 Sec AV SERIES <-- Program Status Area internal station dials [#][5][9] to ask PSTN to switch the internal station <-- SSS=000~255 between these two PSTN calls. The timing of the FLASH signal is programmed here. Def.=004=4 sec.
INITIALIZATION up the call during the conversation will disconnected both 108 Hold Recall Timeout external parties. Interrelation Zones: None 107 Aristel TM 108 Hold Recall Timeout=030 Sec Hold Recall Time <-- Program Status Area <-- SSS=000~255 Aristel AV SERIES TM 107 Hold Recall Time=090 Sec Def.=030=30 sec. <-- Program Status Area <-- SSS=000~255 AV SERIES Description: Def.=090=90 sec.
INITIALIZATION 109 Exclusive Hold Recall Time Aristel TM 109 XHold Recall Time=090 Sec <-- Program Status Area <-- SSS=000~255 AV Def.=090=90 sec. SERIES Description: Holding Time A: The held call does not revert to the holding station. If the exclusive held call is not retrieved prior to the setting time being reached it will revert to the holding station. Holding Time B: The held call reverts to the holding station. Holding Time C: The held call reverts to the Attendant Console.
INITIALIZATION seconds setting time is reached. 113 Transfer Busy Recall Timeout Aristel Pressing [SPK[ key without dialing. Pressing [FUNC] key without dialing. TM 113 Trf Busy Rc Timeout=030 Sec Accessing a CO line without dialing. <-- Program Status Area <-- SSS=000~255 Pressing [SPD] key without dialing. AV SERIES Pressing [∗] key without dialing. Def.=030=30 sec.
INITIALIZATION 115 Interrelation Zones: CFW No Answer Transfer Time Aristel Program Zones 218, 219, and TM 117 115 CFW NoAns Tr Timeout=010 Sec <-- Program Status Area DISA No Dialing Transfer Timeout Aristel TM <-- SSS=000~255 AV SERIES 117 DISA No Dial Timeout=005 Sec Def.=010=10 sec. <-- Program Status Area <-- SSS=000~255 Description: When calling a free station A which is programmed Call Forward No Answer AV SERIES Def.=005=5 sec.
INITIALIZATION prior to the setting time being reached, the CO line will be automatically the setting time is reached. disconnected by the system. The auto-redial function will be placed into Auto Interrelation Zone: Program Zones 604-CO-2 and Redial Pause Time status in PROGRAM ZONE 121.
INITIALIZATION 122 free station the call will be transferred immediately to the next available Busy Reminder Interval Time Aristel station. TM 122 Busy Rem ICM Time=020 Sec Interrelation Zones: Program Zones 604-CO-7(8) <-- Program Status Area <-- SSS=000~255 AV SERIES 124 Def.=020=20 sec.
INITIALIZATION Description: Interrelation Zones: Program Zones 125, 221 and 233 This parameter can only work during ECF or when making another outgoing call through DISA. The Tone Decoder of the system will detect “On” signal of the first Busy Tone sent from CO after the external party hangs up the call. If the time of Busy Tone “On” signal on CO loop is the same as the setting 127 Busy Tone On (II) Detection Time NOTE 3. Aristel time, the system will recognize Busy Tone “On” signal.
INITIALIZATION NOTE 5: Busy Tone (II) is only recognized if the following 130 CO Access Delay Time Aristel parameters are effective. 1. Busy Tone On (II) ----- Program Zone 127. TM 130 Co Delay tm Time=000 Sec 2. Busy Tone Off (II) ----- Program Zone 127. <-- Program Status Area <-- SSS=000~255 AV SERIES Interrelation Zones: Programs Zone 127, 221 and 233 Def.=000=0 sec.
INITIALIZATION 132 free or the line will then be released if all consoles are still busy after three Metering Pulse Delay Time Aristel rechecks. TM 132 Meter Delay Time=000 Sec (*40ms) <-- Program Status Area Interrelation Zone: Program Zone 218, 219 and 400 <-- SSS=000~255 AV SERIES 134 Def.=000=0 sec. Description: Incoming Delay Time Aristel TM This parameter allows the system to remain on the detection of the metering pulse during the setting time after the CO line is disconnected.
INITIALIZATION 135 The 2nd DSS Page Remaining Time or SLT MSG Wait Silence Time Interrelation Zones: Program Zone 212 The 2nd DSS Page Remaining Time Aristel 136 TM 135 Key Page tm Time=006 (*5Sec) <-- Program Status Area <-- SSS=000~255 AV Def.
INITIALIZATION Description: Metering Pulse Detection Starting Time 137 To determine the amount of the SLT ringing interval after a free SLT station has been left the MSG Waiting. Aristel TM 137 Meter range1 Time=008 (∗10ms) Interrelation Zones: <-- Program Status Area <-- SSS=000~255 Program Zone 212 AV SERIES Example 1: PROGRAM ZONE 135=060 and PROGRAM ZONE 136=006 Def.=008=80 ms. Description: (The function is only available in AV-38 and AV-64) Step 1.
INITIALIZATION Time”. 140 DISA Enable Delay Time 2 Aristel TM Interrelation Zones: Program Zones 132, 137 and 251 140 DISA Delay2 Time=000 Sec 139 <-- Program Status Area ACD Enable Time Aristel <-- SSS=000~255 AV SERIES TM Def.=000=000 sec. Description: 139 ACD Tm Time=015 Sec AV SERIES <-- Program Status Area (The function is only available in AV-64 and AV-256) <-- SSS=000~255 If CO line is assigned in PROGRAM ZONE 603-CO-2 = 2 or 3, DISA Def.=015=15 sec.
INITIALIZATION the setting time is reached. 143 Door Call Ringing Time Aristel Interrelation Zone: TM Program Zones 604-CO-2 and 143 Door Ring Tm Time=020 Sec <-- Program Status Area <-- SSS=000~255 142 DISA Enable Delay Time 4 Aristel AV SERIES Def.=020=020 sec.
INITIALIZATION The function is not available in AV-38/AV-64/AV-256.
INITIALIZATION System Function Parameter (Zone 200 ~ 299) 200 Operator Code Aristel PABX (Centrex) Outgoing Code Aristel 201 TM 201 Operator CODE=S (0→9) TM 200 PABX Out CODE=S (0→9) <-- Program Status Area AV <-- Program Status Area Def.=0 <-- S=0~9 AV <-- S=0~9 Description: It is one touch code for station to call operator urgently. Def.
INITIALIZATION Description: 0 = 12 hour format 1 = 24 hour format (Military) Interrelation Zones: Program Zones 503-ST-3 Interrelation Zones: Program Zones 304, 305, 306 and 203 Toll Code Aristel 205 Station Number Digit Length TM Aristel 203 Toll CODE=S (0→9) <-- Program Status Area AV <-- S=0~9 TM 205 Ext Number LEN.=S (2→4) Def.=0 AV <-- Program Status Area <-- S=2~4 Def.
INITIALIZATION 206 phone station when it is intercom-called by another internal station. Digit Length for Local Call Aristel The caller can press [∗] to change the calling type during the calling. TM <-- Program Status Area 206 Local Digit LEN.=S (0→9) 0 = Voice Signaling 1 = Ring Signaling <-- S=0~9 Def.=0 AV Interrelation Zones: None 208 Intercom Dial Tone Signaling Description: Defines the length of a local telephone number restricted in Aristel TM PROGRAM ZONE 203 and 405.
INITIALIZATION 209 Description: Intercom One Digit Dialing Capability Allows an internal caller to press digit [4] to search for the next free Aristel TM station if the called station is busy or does not answer. The next free 209 ICM ODD CAP.=S (0:D 1:E) AV <-- Program Status Area station must be in the same station group as the called station in <-- S=0~1 PROGRAM ZONE 503-ST-1. Def.
INITIALIZATION 212 Message Wait Auto Ringing Aristel Interrelation Zones: TM 213 212 SLT MSG Wait SIGN=S (1:R 2:V) <-- Program Status Area <-- S=0~2 AV Make/Break Ratio Aristel Def.=1 Program Zone 402 TM <-- Program Status Area 213 Make/Break TYPE=S 0:33 1:40 Description: <-- S=0~1 Def.
INITIALIZATION 216 Description: Allows the system to select a free CO line automatically during Speed Dial, Auto Redial and Redial. 0 = Disable CO Delay Capability/Paging Tone of 15 Keys KP Aristel 1= Enable TM 216 15 key page CAP.=S (0:D 1:E) <-- Program Status Area <-- S=0~1 Interrelation Zones: 215 AV None Def.=0 Description: Dial _9 Capability CO Delay Capability Aristel TM The system will delay a setting time after CO line is accessed so 215 Dial_9 CAP.
INITIALIZATION 217 Description: Mute CO Capability Allows DISA caller to be transferred to the Attendant Console if the Aristel TM called station is busy or does not answer. <-- Program Status Area 217 CO Mute CAP.=S (0:D 1:E) 0 = Disable. <-- S=0~1 1 = Enable when No Answer. The call will be transferred to the console(s) Def.=0 AV according to PROGRAM ZONE 219 as soon as the setting time in PROGRAM ZONE 116 is reached.
INITIALIZATION the second time reached. If the call still does not be answered during 2= the 3rd time recheck, the system will disconnect the call immediately. The total maximum recheck times will be three (3) times. Transferred to all Consoles in the same Console Group as the called station group number.
INITIALIZATION Description: DAY TIME : Transfer to the consoles in the console’s group 0 = Disable 1= Enable which is the same group number as Station Group Number of the called station in Interrelation Zones: None PROGRAM ZONE 503-ST-1. The consoles will ring. 221 MIDDAY TIME : Transfer to the consoles in PROGRAM ZONE Busy Tone Detection/Hold Reminder Capability 400-04. The consoles will not ring but have an Alert Tone to be heard from the speaker.
INITIALIZATION it is restricted by PROGRAM ZONE 603. NOTE 10: Busy Tone Detection can only operate during External call Forward (ECF) or Interrelation Zones: Program Zones 503-ST-4, 603 when accessing CO line for another 223 Interrelation Zones: Auto-Redial Times Program Zones 125, 126, 127, Aristel 222 DSS Key for Different CO Group Aristel TM <-- Program Status Area 223 Auto-Redial TIMES=SS 00→99 <-- S=00~99 TM Def.=20 AV 222 DSS for DTG CAP.
INITIALIZATION Description: Interrelation Zone: Program Zone 507-ST-3 Determines the limiting status before the time in PROGRAM ZONE 507-ST-2 is reached. 225 Speed Dial Distribution Aristel 0 = Continuous warning tone after timeoutNOTE 11 1 = A one (1) second warning tone for each Call Limit DurationNOTE 11 TM <-- Program Status Area 225 Speed Dial CODE=S (0→9) 2 = At ten (10) seconds before timeout, a one (1) second warning tone will sound.
INITIALIZATION 600 (100 ~ 699) 5 600 (100 ~ 699) 100 600 6 700 (100 ~ 799) 500 7 800 (100 ~ 899) 400 8~9 900 (100 ~ 999) 300 EXAMPLE: 1. Entering AAA → BBB (where AAA → BBB are variables, eg 100 ~ 255), SPD Codes from 100 ~ 255 can override Toll. When PROGRAM ZONE 227 = 1 = Enable Name Speed Dialing System Speed Dial Sets Setting Value 2. SPD Codes from 234 ~ 456 can override Toll.
INITIALIZATION System or Individual Speed Dial, or entering the prefix of a name to search for the speed dial number. 0 = Disable 229 Busy Reminder Capability Aristel 1 = Enable TM 229 Slt Busy Remind CAP.=S (0:D 1:E) <-- Program Status Area <-- S=0~1 Interrelation Zones: Program Zones 404, 500 - FN=74, Def.
INITIALIZATION Allows the system to maintain its cross-links when an external line is 232 Speed Dial Pause Times disconnected abnormally. Aristel 0 = Disable TM 232 B.B.C. Pause TIMES=SS 00→99 1 = Enable. If the problem is caused by the system itself, the user will experience a short interruption while the connection is restored AV automatically. If the problem is caused by the external CO or a wiring connection, the link will not be restored. <-- Program Status Area <-- SS=00~99 Def.
INITIALIZATION Description: Defines how many cycles of Busy Tone ON + Busy Tone OFF Caution ! If the setting value = 1 will increase the system’s working loading. detected by the system can be assumed as a real Busy Tone sent from CO after the external party hangs up the call. Interrelation Zones: None Interrelation Zones: Program Zones 125, 126, 127, 235 234 CO Auto-Transfer Capability Aristel Aristel TM 234 Co Auto Trf CAP.
INITIALIZATION 236 Description: Dial Tone Detection TimesNOTE 3 A very important function for SLT, especially when SLT is Pulse Aristel TM Dialing. <-- Program Status Area 236 Dial Tn Tms TIMES=SS 00→99 0 = Disable. Pulse dialing SLT cannot use some station functions <-- SS=00~99 which the operation digit is with [#] or [∗]. Digit [7] and [8] can be Def.=06 AV the first digit of the station number. 1 = Enable.
INITIALIZATION 238 DISA Single Digit Dialing Capability Aristel Description: Allows the user to disable “Do Not Disturb” function from the system TM even if the Function Key is assigned for “DND”. <-- Program Status Area 238 DISA Group CAP.=S (0:D 1:E) <-- S=0~1 0 = Disable. System has Do Not Disturb function. 1 = Enable. Def.=0 AV Description: System does not have Do Not Disturb function.
INITIALIZATION 241 Direct Intercom Dialing & FAC Uninhibited by Call Limit Duration Capability Aristel TM <-- Program Status Area 241 Direct Dial CAP.=S (0:D 1:E) 242 Exclusive Hold & System Wide CFW Capability Aristel TM 242 XHOLD CAP.=S (0:D 1:E) <-- S=0~3 AV <-- Program Status Area <-- S=0~3 AV Def.=1 Def.=0 Description: A. Exclusive Hold Capability Description: Allows an internal party to call intercom by dialing station number Allows the user to select Exclusive Hold function.
INITIALIZATION (ISDN DID) rings to an internal BUSY station which NOTE 13:SOS function will only operate with all of the PROGRAM ZONE 504-ST-8=1 and the called busy station following: has heard as twice as Busy Reminding Tone by the setting 1. The user must assign one sensor for time in PROGRAM ZONE 122 the call will be transferred to SOS function in Program Zone 303. the first free assigned Station in PROGRAM ZONE 400-05. 2.
INITIALIZATION 0 = Both Day and Night enable 1 = Day disable, Night enable Interrelation Zones: 2 = Day enable, Night disable 504-ST-3 and System Interrelation Zones: Program Zones 124, 131, 249, 246 Voice Recording Copy Capability Aristel 245 SLT & Voice Mail Message Waiting Function Capability Aristel Program Zone 502-PORT-2, TM 246 VSU REC Copy CAP.=S (0:D 1:E) AV TM 245 SLT MSG FUN. CAP.=S (0:D 1:E) AV <-- Program Status Area <-- S=0~3 Def.
INITIALIZATION Interrelation Zones: Program Zones 400, 402 and System Administrator’s 247 Background Music For CO Incoming Ringing Signal Capability Aristel TM Description: Allows the user to disable/enable Call Forward function. 0 = Disable 1 = Enable Interrelation Zone: 249 <-- Program Status Area 247 Co Ring BGM. CAP.=S (0:D 1:E) <-- S=0~1 Ringing Signal For Door Phone Call Aristel Def.=0 AV System Administrator’s TM 249 Door BGM Rg. CAP.
INITIALIZATION 250 Capability Of Console Entering System SPD/Name SPD/Alarm Description: Allows the system to detect metering Pulse which is a counting signal for telephone call charge sent from CO. Aristel TM 250 Ind. Console CAP.=S (0:D 1:E) <-- Program Status Area 0 = Disable. <-- S=0~1 1 = Detection 12 KHz Metering Pulse signal. 2= Def.=1 AV Detection 16 KHz Metering Pulse signal. 3 = Detection 12 KHz Metering Pulse signal and Enable Hotel Function (EH64).
INITIALIZATION The function will inhibit the outgoing to be made from any internal Interrelation Zones: station during the setting month. 00 = Allowed 254 01 = Disallowed on January None The Way For SLT To Put the Call On Hold Capability 02 = Disallowed on February Aristel ............... 12 = Disallowed on December TM <-- Program Status Area 254 SLT. Flash_7 CAP.=S (0:D 1:E) <-- S=0~1 Def.
INITIALIZATION System Function - 1 (Zone 300 ~ 399) Interrelation Zones: 300 Reset Data To Default Aristel 301 System Password Setup Aristel TM 300 System Reset Reset=S (1→3) AV None <-- Program Status Area TM 301 NN-IP <-- Program Status Area P-PROG <-- S=1~4 <-- NN=01~30 Def.=0 IP=Cursor Position=01~08 AV Description: Description: Allows the user to reset the system data. Provides up to thirty (30) sets of password for different usage. Each password has a maximum of 16 digits.
INITIALIZATION = 100 calls _ _ _ _ dddd = 100 calls AV-64 = 250 calls or 1160 calls (for EH64) (Only available when Voice Service interface is installed) AV-256 = 250 calls or 1160 calls (for EH64) (Refer to System Administrator’s Manual) Default: AV-38 Default: AV-12 dddddddd (Refer to System Administrator’s Manual) NN=06 Reserved for future use. SOS Password (Not available for AV-64 and AV-256) The password work with [#55] and [#57] to turn on/off the SOS function.
INITIALIZATION (Refer to the Operational Manual of SM) NOTE 15: AV-8 = Only one relay, NN = 01. NN=08 NAV-8 = Two relays, NN = 01 ~ 02. Headset Password: The password to enable Headset function. AV-12 Default: AV-38 _ _ _ _ dddd = Two relays, NN = 01 ~ 02. = Two relays, NN = 01 ~ 02.
INITIALIZATION Fire Alarm Application: 00~01 (D1D1 = 1st Sensor, D2D2 = 2nd When sensor is triggered all idle stations will ring continuously Sensor,….., DNDN = Nth and all busy stations will hear the alarm tone. To cancel Fire Sensor) NOTE 16 Alarm, lift the handset and press [#] + [5] + [2]. Def.
INITIALIZATION Table 1 Function SS 00 01 02 03 04 05 06 07 08~18 Table 2 Sensor Type DD Non Operational Fire Alarm (Continuous Alarm) Break In Alarm (Interrupted Alarm) Door 1 Switch Sensor Door 2 Switch Sensor Relay Enable NOTE 17 SOS Sensor SOS and Relay NOTE 17 Reserved 00 01 Low Level Control High Level Control Low level means Normal Close High level means Normal Open 304 Date And Time Aristel 304 T TM D/M/Y W <-- Program Status Area IP <-- IP=Cursor Position=01~06 AV NOTE 17: 05 = Relay
INITIALIZATION 306 Day Time Schedule Interrelation Zone: Program Zone 204 Aristel 305 System Alarm Clock Aristel TM 306 Day TM hh:mm to <-Program Status Area <-NN=Day Schedule NN-IP Number=00~06 TM <-- Program Status Area IP=Cursor Position AV <-- NN=Alarm Schedule 305 Alarm NN-IP 00:00 00 hh:mm Number=01~03 Def.
INITIALIZATION NN = 01 = Monday P = 1 = Recording Start Time = 0 ~ 9 ---> “Start Time” NN = 02 = Tuesday The system will start to count the call duration as soon as the setting NN = 03 = Wednesday time is reached after the CO line is accessed. NN = 04 = Thursday NN = 05 = Friday 0 = 00 seconds, 1 = 05 seconds, …..
INITIALIZATION 4 = 4th cabinet P = 5 Print Out The Title = 0 ~ 1 ---> “Rec_Title” Whether to print out the title.
INITIALIZATION Case Illustration: (Date: December 01) Interrelation Zone: Case 1: Program Zone 228 08:35, Station 12 made a 5 minutes 35 seconds call (Tel. No. 0088629993380) through line 1 and stored Account No. 9125. 308 Midday Time Case 2: 09:00, Station 15 made a call through line 5 but was restricted. Aristel Case 3: 09:10, DISA incoming call through line 3, call duration 5 minutes 19 seconds.
INITIALIZATION HH = End Hour Number MM = End Minute Number = 00 ~ 23 = 00 ~ 59 Weekly Day Setting: NN = 00 = Sunday NN = 01 = Monday NN = 02 = Tuesday NN = 03 = Wednesday NN = 04 = Thursday NN = 05 = Friday NN = 06 = Saturday NN = 07 = Sunday Interrelation Zones: 309 ~ 399 0-53 Program Zones 219, 402, 600 Reserved For Future Use AV-Series System Programming Manual
INITIALIZATION System Function - 2 (Zone 400 ~ 499) (according to the conditions in PROGRAM ZONE 218) will be transferred to the assigned consoles here. The consoles will not ring but have an Alert Tone to be heard from the speaker.
INITIALIZATION are busy the calling station can press [MSG] (or [6]) to leave the message to the first console.
INITIALIZATION digits can be used individually in each group. IP = 20 = Sub-channel number 20 EXAMPLE: Assign each Voice section as one of the following 20 functions. IP = 01~08 Stations positioned here can be called by dialing If the Voice Channel is used for DISA line in AV-64/AV-256, it is necessary to assign the Voice Channel number in PROGRAM numerical digit [1] ~ [8]. ZONE 600 and 601 to be the incoming call station.
INITIALIZATION Voice Service Table Function Code SS 403 Forced Account Code (FAC) Function Illustration 00 No Operation 01 Company Greeting Message 02 Station Busy Message 03 Non Existent Station Message 04 All Consoles Busy Message 05 No Answer Message 06 Holding Message Description: 07 Voice Service Ending Message Allows the user to temporarily break through Toll Restriction. A Reserved For Future Use maximum of 8 digits can be entered.
INITIALIZATION NOTE 19: AV-8/NAV-8 = There are a maximum of 26 sets of Forced Account Codes. NN = 01 ~ 26 AV-12/38 = There are a maximum of 26 sets of Forced Account Codes. NN = 01 ~ 26 AV-64 = There are a maximum of 64 sets of Forced Account Codes. NN = 01 ~ 64 AV-256 = There are a maximum of 99 sets of Forced Account Codes.
INITIALIZATION For Name Entrance status, dial the following numerical key on the Interrelation Zones: Program Zones 100, 225, 227 key phone to enter letter. Once one letter is entered press [DSS3] to go back to the previous position or press [DSS4] to go forward to the next position to set another letter.
INITIALIZATION Office Code A Allowed to dial numbers with Allowed Area Code B, Office Code B Allowed to dial numbers with Allowed Area Code A+B, Office Code A+B Toll Private Line Cannot access the trunk line Reserved 5 6 7 8 9 Interrelation Zones: Key Zones 409/411 Zones 408/409/ 410/411 Program Zone 203, 503-ST-5 LCD Display DSS10 dddddddd DSS15 _ Clear a specific digit DSS20 d Allows any digit to be used.
INITIALIZATION 408 Common Disallowed Code is the first priority in any other Toll Restriction. Area Code - A Aristel A maximum of 11 digits can be entered in each Allowed code TM 408 Area_A _ _ _ <-- Program Status Area NN-IP <-- NN=Area Code NOTE 21 Key Functions.
INITIALIZATION Code 01: Code 02: Code 03: Area Code beginning Any Area Codes are Without any Area with [Toll Access Code] allowed Program Zone 203 and 405 Area Code - B TM 409 Area_B _ _ _ Clear a specific digit DSS20 d Allows any digit to be used.
INITIALIZATION 411 A maximum of 3 digits can be entered in each Code. Set up Toll Access Code and Area Code A beforehand. Office Code - B Aristel PROGRAM ZONE 203 and 408) . TM 411 NN-IP <-- Program Status Area Offi_B <-- NN=Office Code NOTE 21 Key Function: IP=Cursor Position=01~03 AV Key LCD Display DSS10 Description dddddddd Clear all digits Description: DSS15 _ Clear a specific digit Office numbers A are followed by Area Code A (Program Zone 408).
INITIALIZATION EXAMPLE: 411 Office_B 01-IP 69d 411 Office_B 02-IP d__ Code 01: Code 02: 411 Office_B 03-IP _ _ _ Code 03: Office Codes beginning Any Office Codes Without any Office With [69] are allowed Codes are allowed are allowed Interrelation Zone: 412 ~ 499 Program Zone 203, 405 and Reserved For Future Use AV-Series System Programming Manual 0-64
INITIALIZATION Station Function (Zone 500 ~ 599) 2. NNNN = The display for the user to assign each DSS Key as a Station key. Station Number can be two (2) to four 500 (4) digits. Key Group Assignment (For KP) 3. Aristel FN:NN = The display for the user to assign each DSS Key as a TM Function key. 500 Key GP GP-IP NNNN AV FN = Function Code (00 to 99) <-- Program Status Area <-- GP = 01~08, IP = 01~25 Please refer to “Definition of Function Code Table”. 4.
INITIALIZATION Code Definition of Function (FN) Code: Code Function Code 00 Non-Operational Message Waiting/Pulse to Tone Change over Do Not Disturb/Conference MICrophone/Auto Answer Save Account Code Call Forward Call Forward All Call Forward Busy Call Forward No Answer Call Forward Busy/No Answer Follow Me Security Code Temporary Security Code Set Macro Function Set Voice Individual Alarm (Station) Individual Alarm (Console) Date/Time (Console) Help List System Program Speed Dial Console Speed Dial
INITIALIZATION NOTE 23: OPERATION EXAMPLE: 5 Numbers Auto Redialing Operation (only Key Phone can do, and must under handsfree dialing) Step 1. Accessing a free CO line from key station. Step 2. Dialing the desired telephone number and pressing [SAVE] during hearing busy tone or ring back tone, and then disconnect CO line. Step 3. Repeat Step 1 and Step 2 till all the desired numbers are dialed and saved (5 different numbers maximum). Step 4. Pressing DSS Key as [FUNC=85] starting to do Auto-Redial.
INITIALIZATION NOTE 24: OPERATION EXAMPLE: Step 1. Step 2. Step 3. No matter which the dealer makes outgoing call to the user or the user makes incoming to the dealer.
INITIALIZATION NOTE 25: During the external conversation, the internal user can press DSS key as [FUNC=90] to start to enter the Account 502 NOTE 26: AV-8/NAV-8 ---> C S N AV-12 ---> C S AV-38 ---> AV-64 ---> Station Function - Port Parameter Aristel TM 502 Ext. SSSS <-- Program Status Area No P 000000 <-- P = 01~07 = Item SSSS = Station Number AV CSN = Port Number NOTE 26 Description: (P = 1 ~ 7) P = 1 = Station Number ---> "Station No" Very important: S = 10 can not be entered.
INITIALIZATION Interrelation Zones: Program Zones 205 and 227 NOTE 27: 1. If PROGRAM ZONE 205 = 4, then 2 digits [nn] and 3 digits [mmm] station number must be assigned as [00nn] and [0mmm], can not be assigned as [nn00] and [mmm0]. 2. Even though the assigned station number is [00nn] and [0mmm], the caller still can dial [nn] and [mmm] to call the desired station. But the display will show the station number as [00nn] and [0mmm].
INITIALIZATION phone, refer to PROGRAM ZONE 500. NOTE 28: Only available for SLT Station Port. The system will send the following In-Band DTMF Codes as soon as the assigned SLT answers the call under different conditions: Extension calls Voice Mail ==== [#] + [Extension Number] Call Forward All to Voice Mail ==== [∗∗] + [1] + [Ext. No. of ext. A] Interrelation Zones: Program Zones 500 P = 4 ~ 6 = Reserved for future use. P = 7 = Restriction by Intercom Called.
INITIALIZATION P = 1 = Station Group = 1 ~ 8 ---> "Station GP" Station Group is assigned for the following features: 8 = Search a free CO line in the 8th CO group Zone Paging Group Interrelation Zones: Program Zones 202 and 603 Called Pick Up Group Intercom Single Digit Group P = 4 = Incoming CO Group = 0 ~ 8 ---> "Incoming G" Interrelation Zones: Program Zones 209 and 401 Allows the user to answer or pick up the incoming CO line according to PROGRAM ZONE 608.
INITIALIZATION ............ P = 8 = The 2nd page of DSS Key group for Key Phone = "DSS Key GP" To assign a specific group for the second page of Flexible DSS Keys 0 = Cannot override. Interrelation Zones: System Administrator’s Manual on each Key Phone. Refer to PROGRAM ZONE 500 and 503-ST-2.
INITIALIZATION to the same or lower level. Ten levels (0 ~ 9) are available. (0 = the 1 = Station Loud Bell for Relay 1 1 = Station Loud Bell for Relay 1 lowest level - 9 = the highest level). 2 = Secret Recording for Relay 12 = Station Loud Bell for Relay 2 3 = Station Loud Bell for Relay 1 9 = Can pass Message Waiting to levels 0 ~ 9 4 = Secret Recording for Relay 2 8 = Can pass Message Waiting to levels 0 ~ 8 AV-64/256 ............
INITIALIZATION handset (SLT or key phone) is lifted or Speaker On (for key phone 505 Station Function - General Function 1 only) when the assigned station is enabled in PROGRAM ZONE 504-ST-4 and the Relay is set for Secret Recording in PROGRAM ZONE 302.
INITIALIZATION system alarm time is reached. Interrelation Zones: None 0 = Disable 1 = Enable P = 4 = Manual Line = 0 ~ 1 ---> "Manual" If the function is set, lifting the handset or pressing [SPK] will Interrelation Zones: Program Zone 305 and 505-ST-7 automatically call the consoles which the console group number is the same as the station group number of the calling station without P = 7 = System/User Alarm Signal = 0 ~ 1 ---> "Alarm Sig." dialing any digits.
INITIALIZATION 506 Station Function - General Function 2 0 = Disabled = Station can make an intercom call by dialing the station number. Aristel TM 1 = Enabled = Station cannot make an intercom call by dialing the 506 System PSW P 1 0 1 0 0 0 0 0 ST: station number.
INITIALIZATION If function is enabled the assigned station can listen to the P = 5 = Intercom Busy Reminder Tone Capability = 0 ~ 1 ---> "ICM Tone" surrounding area of the lower level handsfree key station. The Level If function is enabled the assigned station will hear a Busy Reminder Tone during intercom call or transferred when it is setting is the same as Zone 504-ST-02. Refer to System Administrator’s Manual for operation method. engaged.
INITIALIZATION 507 Station Function - General Function 3 P = 3 = Forced Account Code = FC NOTE 30 ---> "FAC Code" Aristel TM Allows the user to be temporarily unrestricted during outgoing dialing 507 Port No CSN LD P FC ST: AV by using Forced Account Number code which is the same as the <-- Program Status Area assigned code in PROGRAM ZONE 403. <-- P = 01~03 = Item ST = Station Number If the setting is 00, all Forced Account Numbers are allowed.
INITIALIZATION Aristel TM Interrelation Zones: Program Zone 404 <-- Program Status Area 508 HOT CO SPD:NNN ST: <-- ST = Station Number = 2 ~ 4 digits AV 508 18 HOT CO ST:11 11 = Station No. 18 = The called station number Lifting the handset from Station 11 will intercom call Station 18 Description: Allows the user to dial a specific external number through System automatically without dialing any digits. Speed Dial, or an internal station by lifting the handset.
INITIALIZATION value for each block must be according to the total sets of Individual Speed Dial Codes in PROGRAM ZONE 225 NOTE 31. EXAMPLE: Each block includes 10 sets of Individual Speed Dial Codes. 509 Indivi.
INITIALIZATION CO Function (Zone 600 ~ 699) 600 Incoming Ringing Assignment - Day Time Aristel TM <-- Program Status Area 600 FLX D. CO-IP SS SS SS SS SS SS SS AV <-- CO = CO NumberNOTE 32 IP=Cursor Position=01~16 SS=Station Number =2~4 digits Def.=[11 12 13 14 15 16 17 18] Description: Assigns incoming ringing stations on Day time. The assigned stations can answer incoming calls directly by lifting the handset during ringing.
INITIALIZATION 602 Interrelation Zones: Program Zones 123, 306, 308, 402, 502-CSN-1, 506-ST-6, TM Door <-- Program Status Area <-- GP = Door Phone GP-IP NumberNOTE 33 SS SS SS Incoming Ringing Assignment - Night Time Aristel Aristel 602 604-CO-7 and 609 601 Door Ring Assignment IP=Cursor Position=01~08 AV SS=Station Number =2~4 digits TM <-- Program Status Area 601 FLX N. CO-IP SS SS SS SS SS SS SS AV <-- CO = CO NumberNOTE 32 Def.
INITIALIZATION 603 in PROGRAM ZONE 503-ST-3. CO Group Assignment 603-08-IP Aristel TM 603 CO GRP GP-IP SS SS SS SS SS SS <-- Program Status Area Station presses [ ∗ 8 ] will access a free CO line here <-- GP = CO Group automatically. It will not be effected by the DIAL [9] (or [0]) group SS AV Number (01~08) in PROGRAM ZONE 503-ST-3. IP=Cursor Position SS=CO NumberRefer to NOTE Interrelation Zones: 32, Point 1. 604 Def.
INITIALIZATION 5 = Caller ID (CLI)Refer to UF-CND Operation Manual Interrelation Zones: Program Zones 200 and 202 P = 2 = Outgoing Dialing Signal = 0 ~ 1 ---> "Pulse/Tone" 0 = Pulse signal and DISA Enable Time is according to PROGRAM ZONE 118. 1 = Tone signal and DISA Enable Time is according to PROGRAM ZONE 118. 2 = Pulse signal and DISA Enable Time is according to PROGRAM ZONE 140.
INITIALIZATION 9 = ECF by Speed Dial Code 109 Interrelation Zones: Program Zones 302, 600 Interrelation Zones: Program Zones 404 and 604-CO-3 P = 7 = Incoming Ringing Method for Day = 0 ~ 4 ---> "Ring MTD-D"Refer to NOTE 32, Point 2. P = 5 = Pick Up Capability = 0 ~ 3 ---> "Pick Up" 0 = Day Disable Night Disable 1 = Day Disable Night Enable 2 = Day Enable Night Disable 3 = Day Enable Night Enable 0 = Common Audio on the stations assigned in PROGRAM ZONE 600 (601).
INITIALIZATION Interrelation Zones: Program Zones 122, 123, 600 NOTE 34: There are three (3) different sub-functions included in DISA (Direct Inward Station Access) function: 1. Normal DISA for calling internal station: 1-1. Silence DISA: Incoming calls to the system through DISA line which does not have Voice reminder Service will hear system dial tone after the system answers the call and can call internal stations by dialing the called station number. 1-2.
INITIALIZATION NOTE 35: 606 CO Incoming Ringing Frequency Assignment AV-8/AV-12 ---> CO Loud Bell = 01 NAV-8 ---> CO Loud Bell = 01 ~ 02 AV-38 ---> CO Loud Bell = 01 ~ 02 AV-64 ---> CO Loud Bell = 01 ~ 04 AV-256 ---> CO Loud Bell = 01 ~ 09 Aristel TM 606 CO Fre. 00000000 IP <-- Program Status Area <-- IP=CO NumberRefer to NOTE 32, AV 605 Point 1. S=0 ~ 9 Def.
INITIALIZATION Interrelation Zones: System Administrator’s Manual caller dials the representative Single Digit through DISA line. To call a specific station the caller can dial [6] + [Station Number].
INITIALIZATION 609 Voice Channel For Different CO Line Aristel TM 609 VSU TKR SSSSSSSS <-- Program Status Area IP <-- IP=CO NumberRefer to NOTE 32, 610 ISDN DID Number Aristel TM 610 DID N0 SSS <-- Program Status Area NNN-IP =001~255NOTE 36 Point 1. AV S=0 ~ 2 <-- NNN=DID Code AV Def.= [ 00000000 ] IP=Cursor Position SSS=DID Number Description: Def.= [ 000 ] Allows the user to assign the Voice Channel Number for each Description: incoming CO line.
INITIALIZATION 611 will detect the LAST 2 (or 3) DIGITS (DID Number) of the ISDN DID Station Lookup called number. Aristel TM 611 DID SSS Step 2. System will find the DID Number is assigned in which DID Code in PROGRAM ZONE 610-NNN-IP and compare with ST NNN-IP AV <-- Program Status Area the DID Code in PROGRAM ZONE 611-NNN-IP.
INITIALIZATION 612 ISDN Termination Aristel 613 ISDN Type Aristel TM 612 ISDN Term IP S S S S S S S S S S S S <-- Program Status Area AV TM 613 ISDN Type IP S S S S S S S S S S S S <-- IP=CO NumberRefer to NOTE 32, AV <-- Program Status Area <-- IP=CO NumberRefer to NOTE 32, Point 1. Point 1. S=0 ~ 1 S=0 ~ 2 Def.= [ 00000000000 ] Def.= [ 0000000000 ] Description: Description: Multiple devices can share an ISDN cable (known as an S-Bus).
INITIALIZATION 614 ~ 699 0-93 Reserved For Future Use AV-Series System Programming Manual