Care, Use and Installation booklet TUMBLE DRYER EN English 1 ES Español, 14 F Français, 27 Contents EN Warnings and Safety Instructions, 2 Important safety instructions Grounding instructions Dryer Description, 3 The front The back Control panel Start and Programs, 4-6 Choosing a program Table of programs The controls Laundry, 7-8 ASL65VXS Sorting your laundry Wash care labels Special clothing items Drying times Maintenance and Care, 9 When to switch off the electricity Clean the filter after e
Warnings and Safety Instructions EN ! The appliance has been designed and built according to international safety standards. These warnings are given for safety reasons and must be read carefully. � � � Important safety instructions � WARNING: To reduce the risk of fire, electric shock or injury to persons when using your appliance, follow the basic precautions, including the following: � � � � � � � � � � � � � � � � � � � � Read all instructions before using the appliance.
Dryer Description The front The back Control Panel Drum EN Air Intake Vent Model & Serial numbers Filter Caution: Hot! Control panel OPTION Buttons Programs Guide Clean Filter Progress Light Lights Option Lights The START/CANCEL button starts a selected program. When you press this button there will be one beep and the progress lights will flash to confirm the action. If you have not set a program, the buzzer will beep three times.
Start and Programs EN Choosing a program 1. Plug the dryer into the electrical socket. 2. Sort your laundry according to fabric type (see Laundry). 3. Open the door and make sure the filter is clean and in place (see Maintenance). 4. Load the machine and make sure that the items are not in the way of the door seal. Close the door. 5. If the On/Off light is not lit: Press the ON/OFF button. 6.
Programs EN ! If the On/Off light is not lit; Press the ON/OFF button and then select program. Program What it does... How to set it... Sensor Dry Cottons Dries your clothes on High heat setting , ready for putting away. 1. Position the PROGRAMS knob on 1. Options available: Alarm, Delayed start, Pre 2. Select any Options, if required. Creasecare, Post Creasecare. 3. Press the START button. Dries your clothes on High heat setting , ready for hanging. 1. Position the PROGRAMS knob on 2. 2.
Start and Programs EN The Controls PROGRAMS knob � ! Warning, if after pressing the start button, the programs knob position has changed, the new position will NOT change the program selected. ! Position 0, turning the knob to position 0 resets and cancels a program, the display shows O8 . The display shows either the amount of time delay remaining or an indication of the amount of time left for a drying program. The delay time is displayed in hours and counts down each hour.
Laundry Sorting your laundry � � � � � Wash Care Labels Check symbols on clothing labels to make sure that the articles can be tumble dried. Sort laundry by fabric type. Empty pockets and check buttons. Close zippers and hooks and tie loose belts and strings. Wring out each item in order to eliminate as much excess water as possible. Look at the labels on your garments, especially when tumble drying for the first time.
Laundry EN Special clothing items Times are approximate and can vary depending upon: Blankets and Bedspreads: acrylic items (Acilan, Courtelle, Orion, Dralon) must be dried with special care on LOW heat setting. Avoid drying for a long period of time. � � Pleated or creased garments: read the manufacturer’s drying instructions on the garment. Starched articles: do not dry these with non-starched items.
Maintenance and Care When you should switch off the electricity Check the drum after each cycle Unplug the dryer when not using it, when cleaning it and during maintenance activities. Turn the drum manually in order to remove small items (handkerchiefs) that could have been left behind. Clean the filter after each cycle The filter is an important part of your dryer: it accumulates lint and fluff that is formed while drying. Small items could also become trapped in the filter.
Troubleshooting EN Before you call our Customer Care Department, go through the following troubleshooting suggestions: Problem: Possible causes / Solution: The dryer won’t start. � � � � � � � Drying cycle will not begin. � Its taking a long time to dry. � � � � � � � Program finishes and clothes are damper than expected. The display shows a fault code F followed by one or two numbers. The plug is not plugged into the socket, or not making contact. There has been a power outage.
The display shows a fault code F followed by one or two numbers. � Note down the code and contact the our Customer Care Department. Troubleshooting If you still have a problem call our Customer Care Department on: 11-800-356-0766 888 426 0825 EN Before you call our Customer Care Department, go through the following troubleshooting suggestions: Spare PartsPossible causes / Solution: Problem: The plug is not plugged into the socket, or not making contact.
Notes 12
Installation Instructions Read these instructions with care. These instructions are provided for use by qualified installers, in addition the installation must comply with: � In the United States, in accordance with the National Electric Code ANSI/NFPA70 - latest edition and any State, Municipal or local codes. � In Canada, in accordance with the Canadian Electric Code C22.1 - latest edition and any Provincial, Municipal or local codes.
Installation Instructions EN Exhaust ducting Stacking kit - Residential The ducting system for the dryer must be as short and straight as possible and with as few elbows as possible. Four-inch rigid metal ducting should be used, metal flexible ducting can be used but the maximum length of ducting if using this type will be reduced and bends in the duct will reduce this length further. Never use plastic ducting. All elbows must also be a minimum of 4-inch (100mm) diameter.
Notes 15
© Copyright 2006, Westland Sales, Clackamas, OR 97015 1-800-356-0766 www.westlandsales.