Mini Tank water heater Electric undersink Water heaters GL 2.
IMPORTANT SAFETY INSTRUCTIONS WARNING When using electrical appliances, safety precautions to reduce the risk of fire, electric shock or injury to persons should be followed, including: 1. 2. 3. 4. 5. 6. 7. 8. 9. READ ALL INSTRUCTIONS BEFORE USING THIS WATER HEATER. This water heater must be grounded. Install or locate this water heater only in accordance with the provided installation instructions. Use this water heater only for its intended use as described in this manual.
FIG. 1/1 Temperature & pressure relief valve, 3/4 NPT male Hot water outlet 1/2 NPT male Cold water inlet 1/2 NPT male Temperature & pressure relief valve discharge line to drain 3/4 NPT female tapping for relief valve COMPONENT PARTS OF GL 2.5 - GL 4 FIG.
DIMENSIONS FOR GL 2.5 - GL 4 FIG. 2/1 14” 10 1/4” 6” 3 3/4” 5 1/2” 1” 1/2 NPT MALE 12 1/4” 7 1/2” GL 2.5 3 1/2” 3” 14” 2 1/2” GL 4 FIG. 2/2 DIMENSIONS FOR GL 6+ (HORIZONTAL INSTALLATION) 3” 17 1/2” 11 1/2” 3/4 NPT MALE 14 1/2” 8 1/2” 4 1/2” 17 1/2” FIG.
General remarks CAUTION The manufacturer cannot be responsible for the damages caused by improper installation or by failure to follow instructions in this pamphlet. Comply with the installation instructions before completing electric connection. CAUTION The thermostat has been pre-set at the factory between 41°C (105° F) and 45° C (113° F). CAUTION Hydrogen gas can be produced in a hot water system served by this heater that has not been used for a long period of time (generally 2 weeks or more).
Floor Mounting Heater can sit on floor. Pipe connections Connect the cold water inlet pipe to the inlet nipple (marked with a blue ring) and the hot water outlet pipe to the outlet nipple (marked with a red ring).
Maintenance instructions Note: Do not attempt to repair this water heater yourself. Call a service person for assistance. Always turn off the power supply to the heater prior to servicing or draining the heater. PERIODIC MAINTENANCE AND PARTS REPLACEMENT Note: For most of these operations, the water will have to be drained from the heater. For all of these operations the power supply needs to be shut off and the front cover removed. Draining the Heater Remove cover plate V (fig.
Changing the heating element 1. Turn off power supply and drain the heater (see previous section). 2. Remove the heating element (see section on Removing the Heating Element). 3. Install new element with gasket, making sure the gasket and element are positioned correctly. Tighten the retaining nuts and make the wire connections. 4. Refill tank with water before restoring power. Changing the thermostat 1. Turn off power supply. 2. Disconnect the 2 push/pull type wires on thermostat. 3.
FIG. 3/1 N G FIG. 3/2 G FIG. 3/3 Z F X Y T FIG. 3/4 B FIG.
ARISTON • LIMITED 6 YEARS WARRANTY COVERAGE ARISTON, THROUGH ITS U.S. DISTRIBUTOR CONTROLLED ENERGY CORP., (hereinafter CEC) guarantees this water heater to the Owner (hereinafter “Owner”) of the water heater at the original installation location against defects in material and workmanship for the periods specified below. WARRANTY PERIOD 1.
COMMON SENSE HEAT & HOT WATER TECHNOLOGY Merloni TermoSanitari SpA Viale Aristide Merloni, 45 60044 Fabriano (AN) Tel. 0732.6011 Telefax. 0732.602331 Telex 560160 http://www.mtsgroup.net Controlled Energy Corp. 340 Mad River Park Waitsfield, VT 05673 800-642-3111 802-496-4436 Fax 802 496-6924 www.controlledenergy.com 29.1.60.542.1.01 0900 Litograf s.r.l.
