Technical data

14 ARISTON DISHWASHER - Instructions for installation and use
D
ISHWASHER
You have loaded your dishes and you now have to set the
wash cycle. It takes just one minute to learn how
Starting the dishwasher
Ready, steady, go!
First of all.
Turn on the water tap com-
pletely and press ON-OFF but-
ton "A". you will hear a short
beep and indicator light "B"
lights up. Now the appliance is
on and awaiting instructions.
Selecting the wash
cycle.
Select the wash cycle by press-
ing button "P". Each time you
press the button, a beep will
sound and indicator lights "E"
will light up in sequence:
choose the cycle you deem
most suited to the type of
dishes to be washed (take a
look at page 16, where you will
find the wash cycle table). If the
appliance door is shut, press
the Start button "R" and you will
hear a beep; the cycle will start
up within a few seconds.
The dishwasher informs
you.
Your dishwasher is fitted with
indicator lights (G) which light
up to indicate the cycle phase
under way.
Here are the symbols corre-
sponding to each cycle phase:
pre-wash, wash, rinses, drying.
At all times, your dishwasher
tells you which cycle phase is
under way.
Modifying a wash cycle
in progress.
But if you have chosen the
wrong cycle, not to worry! You
can modify the wash cycle in
progress, if it has only just
started. Keep the RESET but-
ton "R" pressed for about 5 sec-
onds: a prolonged beep will
sound, followed by three short
beeps. Indicator light "G" will
turn off and at this stage, all the
settings will have been can-
celled. You are now free to re-
set the correct wash cycle.
You've left out a dish?
Well, it happens to everyone. In-
terrupt the wash cycle by press-
ing the ON-OFF button, insert
the dish you had forgotten and
press the ON-OFF button again.
The cycle will start up from
where you interrupted it.
Finished?
The end of the wash cycle is in-
dicated by two short beeps and
the flashing of the drying phase
indicator light.
 Turn off the water tap.
 Wait a few minutes before un-
loading the dishes: they
are very hot! If you wait a lit-
tle while, they dry better
thanks to the steam.
 Empty the lower rack first.
You decide when it
starts.
When you have loaded the
dishes, you can choose when
to start your dishwasher before
setting the wash cycle desired.
Press button "D" to delay the
start of the wash cycle by 12, 9,
6 or 3 hours. Each time you
press it, you will hear a short
beep and the indicator light "G"
corresponding to the selected
delay will light up.
Now you can select the desired
wash cycle. Press the start but-
ton "R" and after you hear the
beep, the countdown to the de-
layed start will begin.
Once this time is up, the indi-
cator light will stop flashing and
the wash cycle will begin.
If you have set a 12 hour delay,
for example, once you have
selected the wash cycle, the 12
hour indicator light will flash
followed by the others in
sequence until the set time
delay is up. A quick look at the
indicator lights will keep you
informed of the countdown
progress at all times.
Have you changed your
mind?
If you change your mind, you
can set a shorter time delay:
press button "D" to select it. You
need not reset the wash cycle.
If on the other hand you want
to cancel the delay set and you
want the cycle to start immedi-
ately, press button "D" repeat-
edly until the cycle starts and
indicator light "G" correspond-
ing to the cycle start phase
comes on.
Dual function of
indicator lights "G"
1) flashing to indicate a de-
layed start: to remind you that
you have set a delayed start;
2) on and not flashing be-
neath the cycle phase sym-
bol:
meaning the cycle has started
and is in the phase indicated by
the symbol.
Would you like to see
which settings you
have made?
At any time, when the cycle is
under way, if you press button
"P", the cycle in progress indi-
cator light will light up for a few
seconds.
Make sure the wash
cycle has ended
before removing the
dishes!
Warning:
Turn the appliance off by
pressing button A,
unplug the appliance from
the electricity socket to cut
off the power supply; the
power supply cable should
consequently be easily
accessible.
There's been a power
failure? Have you
opened the dishwasher
door?
The wash cycle stops and then
restarts when the electricity
comes back on or when you
shut the door. Everything is
under control!
If opening the door
soon after the end of
the programme,or
during it, stand
away from the
Dishwasher, to
avoid possible injury
from hot steam.