INSTALLATION GUIDE RCC300-SM Subwoofer Module RCC300-FS Freestanding Subwoofer RCC300-SA Subwoofer Amplifier RCC300-CM Cabinet Mount
Thank you for choosing Artison’s RCC 300 Subwoofer System. We are pleased that you have selected our high-performance audio products. INTRODUCTION The following information will guide you through the installation and setup of your Artison RCC 300 Subwoofer Module, RCC 300 Freestanding Subwoofer, RCC 300 Subwoofer Amplifier and RCC 300 Cabinet Mount. Your RCC300-SM carton should contain the following: 1 . RCC 300 Subwoofer Module 1 . RCC 300 Subwoofer Module Paint Shield 1 .
RCC 300 SUBWOOFER MODULE (RCC300-SM) The RCC 300 Subwoofer Module can be installed into either an: Artison Pre-Build Box (Volume ≈ 0.6 ft3) SOLD SEPERATELY OR Infinite Baffle (i.e. 2x4 stud wall, 16” On Center spacing at least 4 feet tall, Volume 1.4 ft3 or greater) IMPORTANT: In an installation of two RCC300-SM’s that are being powered by one RCC300-SA, both Subwoofer Modules need to be in either Pre-Build Boxes or be in Infinite Baffles.
area when installing the module. INSTALLATION INTO AN INFINITE BAFFLE 1. Use the provided Cut-out Template to mark the desired wall location. Be sure that no piping, wall studs, or electrical wires interfere with the placement of the RCC300-SM. 2. Once the hole is cut and the speaker wire is run, manage the speaker wire around the RCC300-SM. 3. Connect the bare speaker wire ends to the spring-loaded binding posts. 4. Install the RCC300-SM into the cut-out made in the wall. 5.
RCC 300 FREESTANDING SUBWOOFER (RCC300-FS) SUBWOOFER PLACEMENT AND ORIENTATION The RCC 300 Freestanding Subwoofer comes with four rubber feet to attach to the side of your choice. Carefully decide what placement and orientation are best for the subwoofer, the supplied rubber feet are not removable once applied. The classical rule for subwoofer placement is that the subwoofer should be placed near the same wall the front channels are located, at one-third of the total distance of the wall.
RCC 300 SUBWOOFER AMPLIFIER (RCC300-SA) The RCC 300 Subwoofer Amplifier can be installed into either cabinetry, on an equipment shelf, or it can be rack-mounted into a standard 19” Equipment Rack. In any installation be sure to provide adequate ventilation around the amplifier. The RCC300-SA has two simple and conveniently placed mode settings. The Music or Movie user controls are located on the front panel for selection based on the source material.
RCC300-SA FRONT PANEL CONTROLS GAIN – The position of this knob controls the overall gain (volume) of the subwoofer. Press this button in and it will spring out into a rotating knob, press it back in to hide it. The front panel gain control will become the master gain control until the remote is used. NOTE: The amplifier by default will resume to the last setting by either gain control device. DIM – This button controls the brightness of the Halo lighting on the front panel.
2. The Red Switch is the input voltage setting; select the appropriate 120V or 230V setting. 3. Connect the detachable IEC Power Cord underneath the Red Voltage Selection Switch. AUDIO OUTPUTS 1. Connect the speaker wires to the Binding Posts. NOTE: Red is Positive and Black is Negative. 2. Use either Bare Speaker Wire or Banana Plugs to terminate the speaker wire. AUDIO INPUTS 1. Connect to either the Balanced Female XLR or Unbalanced Female RCA Inputs.
IR FEEDTHRU 1. Connect a ⅛” Stereo MINIJACK to control the RCC600-SA via your integrated control system. 2. Both the IR Feedthru Jack and the Front Panel IR receiver are designed to allow the User functions to be programmed into an external remote. The Hexadecimal codes for the amplifier are located on the web at: http://www.artisonusa.com POWER MODES 1. Select either: ON – Always On. AUTO – On with Signal Sense, without signal it will stay on for ≈15 minutes. TRIGGER – On with a 12 Volt trigger. 2.
1. EQ – Select the appropriate setting based on these guidelines: ∞ Baffle – The RCC 300 Subwoofer Module is installed in a wall that has an air volume of ≥1.4 ft3. CLOSED BOX – The RCC 300 Subwoofer Module is installed in an Artison In-Wall Pre-Build Box or is the RCC 300 Freestanding Subwoofer. IMPORTANT: In an installation of two RCC300-SM’s that are being powered by one RCC300-SA, both Subwoofer Modules need to be in either Pre-Build Boxes or be in Infinite Baffles.
EQ MODES – Automatic Room Mode Correction (ARMC) The amplifier comes from the factory set to BYPASS. This setting produces a flat frequency response at the subwoofer module. In some cases your room response may benefit from ARMC. Eigen-modes, also known as room modes, exist in all rooms. These room modes are an interaction between the listening room itself, the location of the subwoofer, and the low frequency wavelengths being on the same order as the room dimensions.
microphone at your normal listening position if you plan to use the amplifier in this setting b. One Long, Two Short Flashes – Amplifier Error, Shorted Audio Outputs. Remove the speaker wires from the amplifier and use an ohm meter to check for shorts in the line. c. One Long, Three Short Flashes – Over Temperature Indicator. Be sure that the amplifier has adequate ventilation. If the situation continues to exist contact Artison. 4.
LIMITED WARRANTY This warranty remains in effect for five years from the date of purchase for speaker products and one year for electronic products. THIS WARRANTY PROTECTS THE ORIGINAL OWNER PROVIDING THAT THE PRODUCT HAS BEEN PURCHASED FROM AN AUTHORIZED ARTISON DEALER IN THE UNITED STATES. THE ORIGINAL BILL OF SALE MUST BE PRESENTED WHENEVER WARRANTY SERVICE IS REQUIRED.