Technical information
31
* To pressure reducing valve ** Tested in accordance with EN12897:2006 (1) Single Phase
151.1
12
7
3.5
3.5
6
7/90
3.5
240
3+3
(1)
3:19
2:24
3.5
-
-
-
-
-
-
-
1.68
30
0
<5
211.7
12
7
3.5
3.5
6
7/90
3.5
240
3+3
(1)
4:51
3:17
3.5
-
-
-
-
-
-
-
1.93
41
0
<5
299.8
12
7
3.5
3.5
6
7/90
3.5
240
3+3
(1)
7:19
4:56
3.5
-
-
-
-
-
-
-
2.27
60
0
<5
209.5
12
7
3.5
3.5
6
7/90
3.5
240
3
(1)
4:51
3:17
3.5
85
238
0.9
24.0
0.89
35
24
1.93
43
0
<5
253.3
12
7
3.5
3.5
6
7/90
3.5
240
3
(1)
5:56
3:39
3.5
85
262
0.9
24.59
0.89
41
31
2.26
49
0
<5
-
12
7
3.5
3.5
6
7/90
3.5
240
3
(1)
-
-
3.5
85
tba
tba
27.0/20.0
1.1/0.75
24
17
1.13
53
0
<5
-
12
7
3.5
3.5
6
7/90
3.5
240
3
(1)
-
-
3.5
85
tba
tba
27.0/20.0
1.1/0.75
34
24
1.49
66
0
<5
Model
AQUAVBRAVO ITI 100-300
AQUABRAVO ITD 100-300
AQUABRAVO ITSI 210 - 300
Make of Pressure
Reducing Valve
Make of
Safety Valve
Make of
T&P Valve
SYR 3.5 Bar (22mm)
SYR 3.5 Bar (22mm)
SYR 3.5 Bar (22mm)
SYR 6 Bar (22mm)
SYR 6 Bar (22mm)
SYR 6 Bar (22mm)
CASHH 7 Bar (15mm)
CASHH 7 Bar (15mm)
CASHH 7 Bar (15mm)
126.7
12
7
3.5
3.5
6
7/90
3.5
240
3+3
(1)
2:46
2:03
3.5
-
-
-
-
-
-
-
1.40
27
0
<5
77.2
12
7
3.5
3.5
6
7/90
3.5
240
3
(1)
1:33
1:21
3.5
85
189
0.9
17.7
0.5
14
10
1.20
22
0
<5
146.2
12
7
3.5
3.5
6
7/90
3.5
240
3
(1)
3:19
2:24
3.5
85
186
0.9
17.46
0.78
30
22
1.68
30
0
<5
-
12
7
3.5
3.5
6
7/90
3.5
240
3
(1)
-
-
3.5
85
tba
tba
27.0/20.0
1.1/0.75
29
20
1.29
60
0
<5
296.4
12
7
3.5
3.5
6
7/90
3.5
240
3
(1)
7:19
4:56
3.5
85
238
0.9
26.1
0.89
49
34
2.31
65
0
<5
AQUABRAVO ITD 150
AQUABRAVO ITD 215
AQUABRAVO ITD 305
AQUABRAVO ITI 130
AQUABRAVO ITI 215
AQUABRAVO ITI 255
AQUABRAVO ITSI 215
AQUABRAVO ITSI 305
AQUABRAVO ITD 130
AQUABRAVO ITI 80
AQUABRAVO ITI 150
AQUABRAVO ITSI 255
AQUABRAVO ITI 305
Nominal Capacity ** l
Maximum Water Supply Pressure* bar
Maximum Design Pressure bar
Operating Pressure bar
Expansion Vessel Charge Pressure bar
Expansion Relief Valve Setting bar
Pressure & Temperature Relief Valve Setting bar/°C
Pressure Reducing Valve Set Pressure bar
Electrical Supply V
Immersion Heater Rating kW
Immersion Heater Type
Direct Reheat Time (Single element) (100%) h:min
Direct Reheat Time (Single element) (70%) h:min
Maximum Primary Pressure bar
Maximum Operating Temperature (heating fluid) ºC
Pressure Drop Through Primary Coil mbar
Primary Flow Rate m
3
/h
Heat Exchanger Performance (Flow rate 0.9m
3
/h) kW
Coil Surface Area m
2
Reheat Time ** min
Indirect Reheat Time (70%) min
Heat Loss (kWh in 24h)
Nett Weight Kg
Ozone Depletion Potential (ODP)
Global Warming Potential (GWP)
124.6
12
7
3.5
3.5
6
7/90
3.5
240
3
(1)
2:46
2:03
3.5
85
176
0.9
17.28
0.67
25
18
1.40
28
0
<5
Note: The above cylinders were tested in accordance with EN12897