5407525 Issue 1 Jan 2010 ARISTON Electromechanical Vented Tumble Dryers Models Covered Comm. Code TVM63X NA 63076 Service Information Indesit Company UK Ltd © 2010 Reg.
Indesit Company SAFETY NOTES & GENERAL SERVICING ADVICE 1. This manual is NOT intended as a comprehensive repair/maintenance guide to the appliance. 2. It should ONLY be used by suitably qualified persons having technical competence applicable product knowledge and suitable tools and test equipment. 3. Servicing of electrical appliances must be undertaken with the appliance disconnected (unplugged) from the electrical supply. 4.
Indesit Company INDEX Safety & Servicing Notes & Serial Number Information . . . . . . . . . . . . . . . . . . . . . . . . . 2 Serial Number / Industrial Code Explanation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Machine Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 6 Console . . . . . . . .
Indesit Company TECHNICAL INFORMATION Models Covered TVM63XNA 63076 White First Produced 2009 Electrical Rating 115 Volts AC 60Hz Power Consumption 1.45 kW Plug Type USA NEMA 5.15 Cable Length 1.8 Metres Features Reversing - Dual Heat - 170 minutes Programme Timer, Easy Iron (crease removal) and Auto Drying options.
Indesit Company MACHINE FUNCTION Cold air is drawn into the dryer cabinet interior through louvres in the cabinet base, passes through the large hole in the inner back panel adjacent to the fan and is driven through the element housing on the inner back panel. After passing through the element windings and through holes in the drum back plate into the drum interior, the now warm air is driven through the load to the front of the drum.
Indesit Company Sequence of Automatic Drying System • First 20 minutes, full heat controlled by the timer. This is to pre-heat the clothes and drum before the exhaust thermostats take control. • The timer moves to its next cam position. The timer motor is now disconnected and the dryer tumbles and heats. • When the clothes are dry, the exhaust thermostat opens. This provides a Live supply to the timer motor. The timer moves to the next cam position. • 5 minutes of tumbling with the lower element only.
Indesit Company PROGRAMMES Program What it does... How to set it... Note: Timed Drying up to 170 minutes Dries wet clothing that will be ironed, acrylic fibers or small loads (less than 2 lb / 1 kg). 1. Select required heat setting HIGH HEAT or LOW HEAT by pressing the HEAT button. 2. Position the PROGRAMS knob on the desired time. 3. Press the START button. Consult suggested drying times ( see Laundry). Fabric Care Heating elements turn themselves off and clothing is cooled down.
Indesit Company COMPONENT DESCRIPTION CONSOLE PANEL This panel contains the user controls, which consist of a timer knob, for selecting the timed and sensed drying periods and a push switch for heat selection. TIMER The timer system is made up from two timers, one mounted on the console and one in the base of the machine. Timer 1 controls the motor and heater. This has a spindle to which a knob is attached to enable the user to select the required programme.
Indesit Company DOOR INTERLOCK Bitron Door Lock Operation door hook solenoid bistable cam latch Switch blade lever Door Open - Dryer Off Trying to turn the machine on with the door open, the solenoid is unable to operate the bistable cam to close the contacts, because it is locked by the latch. Door Closed - Dryer Off Closing the door, the latch (now rotated by the door hook) allows the movement of the bistable cam, but the dryer is still OFF until the solenoid is energised.
Indesit Company HEATER ELEMENT The element comprises of front and rear pressings spaced apart with Mica type insulating material. Through the insulating pieces are 4 runs of coiled resistance wire supported from end to end by insulating material. High temperature insulated wires are crimped to the ends of the resistance strips to complete the circuit. Note: Heater assemblies manufactured by Blasi and DBK are interchangeable if replaced as an assembly. Both types are used in production.
Indesit Company MOTOR A two pole P.S.C running at 2800 rpm with the impeller fitted to the rear end of the shaft and the drive belt running directly in grooves in the front end of the shaft. It is protected from overload by a self-resetting internal cut-out which interrupts the electrical supply to the windings. It is used together with a capacitor that is mounted on the base of the dryer. DRUM REAR SEAL This unit comprises of a ring of foam with a webbing bearing face.
C 3 - C 1 (C 3 - C 4) sta t s elect A 9 - A 1 1 (A 1 - A 2) T im e r & M oto r A 1 - A 3 (B 3 - B 4 ) B u zze r B 1 0 - B 1 1 (B 2 - B 1 ) H ea ter B 3 - B 1 (A 4 - A 5 ) 7.5 mins 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 5 min 5 min 5 min 5 min 2.5 min 2.5 min 59 2.
Indesit Company PINK 160025148 TIMER - EC A11 BROWN 160025152 ORANGE B5 BLUE B8 B9 HEAT SWITCH BLUE ORANGE M ORANGE BROWN M BROWN BLACK 160024277 M WHITE START SWITCH REVERS'G TIMER THERMOSTAT EARTHING BRACKET ORANGE WHITE M B11 B12 ORANGE 160020222 VIOLET 160020223 160020224 B9/ B10 WHITE BLUE PB TM RED PB PB CAPAC -ITOR BROWN WITH BOOT PINK M BLACK 160025149 ORANGE 160020222 PTC SOLENOID 4 A11 ORANGE Programme Timer Wiring BLACK BLACK 13 of 19 VIOLET 160020404 A
Indesit Company DISMANTLING INSTRUCTIONS SAFETY NOTES 1. Ensure that the machine is unplugged before commencing any work. 2. Beware of sharp edges on metal panels and pressed parts. A 1. 2. Top Cover Remove the 2 screws securing the top cover to the back panel. Slide the top cover back and lift clear of the console. B 1. 2. 3. 4. 5. 6. 7. Console Panel Remove the top cover as in (A). Remove the 2 screws securing timer mounting plate to the console and unclip from the console.
Indesit Company F 1. 2. 3. 4. 5. 6. Side Panels Remove the top cover as in (A). Remove the plinth by pulling forward. Remove the screw behind the plinth. Remove the screw securing the side panel to the front panel. Remove the 4 screws securing the side panel to the rear panel. Pull the side panel backward to disengage from the lugs on the base panel. G 1. 2. 3. 4. 5. 6. 7. Front Panel & Air Duct Remove the top cover as in (A). Remove the console complete as in (B7). Remove the plinth.
Indesit Company M 1. 2. Door Hinges The door must be removed and split as in (L1) - (6) above. Turn the door hinges inwards and slide the hinge upwards to disengage from the rear trim moulding as in Fig 1. Fig. 1 N 1. 2. Front Bearings Remove the front panel as in (G). Spring the fixing lug out of the open slot in the bearing mounting bracket and slide the pad along the bracket to free the other lug as illustrated. O 1. 2. Drive Belt Removal - if not broken Remove the right hand side panel as in (E).
Indesit Company 3. 4. Drive Belt Fitting Slide the new belt onto the drum and replace the front panel. Place the Special Tool, Part No. C00142716 (5600266), onto the inside edge of the new belt (cut out section of tool facing the drum). Ease the special tool onto the motor shaft as far as possible. Rotate the special tool in either direction to refit the belt onto the shaft. P 1. 2. 3. Capacitor Remove the right hand side panel as in (F).
Indesit Company T 1. 2. Rear Seal Remove the drum as in (Q). Remove the rear seal and clean any remnants of the seal and adhesive from the inner face of the inner back panel. Fit the new seal using adhesive Part No. C00981027 (981027). U 1. 2. 3. Motor Remove the right hand side panel as in (F). Remove the heater cover - 8 screws. Remove the 2 fans from the motor hub - 3 hex head screws. Note: The inner and outer fans are DIFFERENT. Ensure fans are reassembled in the correct order.
Indesit Company Service Manual UK English 19 of 19
