ADVISOR CD 7203 CD95/15003 User Manual Software from version: V6.
COPYRIGHT SLC BV 1996. All rights reserved. No part of this publication may be reproduced, transmitted, stored in a retrieval system, or transmitted in any form, or by any means - electronic, photocopying, recording, or otherwise - without the prior written permission of SLC BV. DISCLAIMER SLC BV makes no representations or warranties with respect to the contents hereof and specifically disclaim any implied warranties of merchantability or fitness for any particular purpose.
CONTENTS INTRODUCTION ..................................................................................................................................... 4 USING THE KEYPAD.............................................................................................................................. 5 The CD3008 keypad............................................................................................................................. 5 The display ....................................................
INTRODUCTION Thank you for choosing an ARITECH security system. When properly maintained, the system will provide years of reliable operation. This manual explains how to use the ARITECH CD72 and CD95 series for every day use. There is a more detailed manual available for managers which explains how to carry out a wider range of operations. These instructions apply to both the CD95 and CD150.
USING THE KEYPAD This chapter describes the alarm system keypad. THE CD3008 KEYPAD The keys These keys are used to enter your code. Always begin with zero (0) and then enter your code. After entering the code, you can carry out the operations assigned to it. 0-9 The options assigned to a code can be adjusted by the installer or manager. " When you are in an option list, this key can be used to go backwards in the list. During arming you can exclude zones. See Special keys.
THE DISPLAY The display is the link between you and the security system. The text messages displayed show where and when faults or alarms have occurred. The display can also show a list of operations from which you can select. Examples of the messages which can appear include: TUE 23 APR 07.40 The date and time are always displayed, regardless if the system is armed or not. You can ask the installer to replace it with another message, if you want. Arm Menu !), you enter an option list.
USING A SINGLE ALARM SYSTEM This chapter explains how to switch on and off an alarm system for premises with only one alarm system. These instructions also apply to users who only have access to a single alarm system in the premises, although several systems may actually be present. Depending on how the system has been programmed, you may not need to do all the steps shown in the instructions. If you enter the wrong code 10 times consecutively, the system is automatically locked for 90 seconds.
Beeeep The alarm is now set. System Armed The current date and time automatically appears. TUE 23 APR 07.40 ARMING A SYSTEM WITH OPEN ZONES When arming (switching on) the system, you may get the message ‘Open Zone(s)’ along with a list of the zones in the premises that have not yet been closed. You should close these zones and then retry arming the system. However, occasionally you may not be able to close an open zone because, for example, a door lock or magnetic contact may be malfunctioning.
6. Press the number of the open zone, in this example ‘2.’ 2 Inhibit Zone 2 The system then confirms which zone you have excluded. 002 Hall If another zone is open, it will be listed and you must again press " and the zone number to inhibit it. Is Inhibited The alarm is being set. System Arming The buzzer begins to beep. You must now exit the protected area by the designated exit route. Leave now Beeeep The alarm is now set. System Armed The current date and time will automatically appear.
DISARMING A SYSTEM AFTER AN ALARM The bell and the flashing light are activated when an alarm is triggered in the system. If your system has the option, a report of the event is automatically sent over the phone lines to a central station. If you inadvertently activate an alarm, immediately telephone the central station to prevent an unnecessary response. When you enter the premises after an alarm, the bell may already be silent if it has been so programmed. This allows there to be several alarms.
USING A SPLIT SYSTEM When the system was installed it was divided into different security areas. A system that has more than one security area it is called a split system. These different areas were programmed by the installer. Depending on how the system was programmed, your code may give you access to one or more of the security areas. Depending on how the system has been programmed, you may not need to do all the steps shown in the instructions.
ARMING A SPLIT SYSTEM As explained at the beginning of the chapter “Using a split system,” a split system can be programmed to show two different standby message displays, and two different ‘selection’ messages after entering your code. The instructions below use the displays “Time/Date” and “Area [number] armed.” If your code lets you access more than one security area, you can select one of them to arm. 1. Go to the keypad. The current date and time are displayed. An example is shown. 2.
7. Press the Accept key again. ! Normal Set ! Normal Set " Area 2 is arming. If programmed, the buzzer for the area will begin. Area 2 Arming Beeeep You must exit the protected area by the designated exit route. Leave Now Area 1 Armed Both areas are now armed. Area 2 Armed Enter Area No. TUE 23 APR 07.41 ARMING A SPLIT SYSTEM WITH OPEN ZONES When arming (switching on) the alarm, you may get the message ‘Open Zone(s)’ along with a list of the zones in the premises which have not yet been closed.
0 + code Enter Code **** In this example, areas 1 and 2 are disarmed. Area 1 Disarmed Area 2 disarmed You have a few seconds to enter the number of the area you want to arm. 3. Enter Area No. Enter the area number (in this example it is 1). 1 Arm Menu 4. Press the Accept key. ! Normal Set 5. Press the Accept key again. ! Normal Set " 6. The system has identified zones in the area that are not properly closed. Open Zone(s) It then proceeds to list the open zone(s).
DISARMING A SPLIT SYSTEM If you enter the premises when the system is armed, the buzzer will begin to beep (if programmed) with an intermittent tone to indicate that the entry period has begun. As long as this beeping continues, you can disarm (switch off) the system with your code without activating an alarm. You also must not enter other areas of the system during the beeping. If you do, a siren will sound and a full alarm condition may occur.
DISARMING A SPLIT SYSTEM AFTER AN ALARM The bells and the flashing light are activated when an alarm is triggered in the system. If your system has the option, a report of the event is automatically sent over the phone lines to a central station. If you inadvertently activate an alarm, immediately telephone the central station to prevent an unnecessary response. When you enter the premises after an alarm, the bell may already be silent if it has been so programmed, but the red LED will still be activated.
If there are other alarms, they are shown one after another. A summary of the status of the areas appears. If you wish to make more changes, enter the number of the area you want to change. Otherwise the standby message automatically appears. Area 2 Armed Enter Area No. TUE 23 APR 07.
UPLOADING AND DOWNLOADING IN THE CD72 AND THE CD95 The CD72 and CD95 series has the option of controlling, modifying and programming the alarm system remotely by the installer. With the use of a modem messages can be sent from the control panel to a personal computer (PC), called uploading, and from a PC to the control panel, called down loading. Uploading and downloading is therefore a quick and handy aid to easily discovering and solving problems.
OVERVIEW OF THE OPTIONS AVAILABLE The following flowchart provides an overview of all the options available from the CD72 and CD95/150 alarm systems. It also shows the keypad keys you need to press in order to arrive at the options. Options listed below in grey are only available for the CD95/150 alarm system. The symbols used to represent the keys are as follows: ! Accept X Reject ↓ Move forward ↑ Move backward OPTION LIST FOR THE CD72/95/150 There are nine main menu options in this system.
Flowchart of the CD72/95/150 User Options Page 20 User Manual for CD72/95/15003
User Manual for CD72/95/15003 Page 21
Page 22 User Manual for CD72/95/15003
User Manual for CD72/95/15003 Page 23
Page 24 User Manual for CD72/95/15003
