CS450 User Manual 143163999-2
COPYRIGHT SLC BV 1997. All rights reserved. No part of this publication may be reproduced, transmitted, stored in a retrieval system, or transmitted in any form, or by any means - electronic, photocopying, recording, or otherwise without the prior written permission of SLC BV. DISCLAIMER SLC BV makes no representations or warranties with respect to the contents hereof and specifically disclaim any implied warranties of merchantability or fitness for any particular purpose.
Table of Contents Important Telephone Numbers ........................................................ 4 Alarm Zones .................................................................................... 4 The Keypad ..................................................................................... 5 Using the Keypad ............................................................................ 5 Short Codes.....................................................................................
Important Telephone Numbers Alarm Company Local Police Station Other Alarm Zones Write the names of the zones here Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8 Zone 9 Zone 10 4 CS450 User Manual
The Keypad Green Light Mains Power ON Orange Light Fault in Alarm System Red Light Alarm Using the Keypad Return to previous menu t Press repeatedly to return to ‘Finished’ display Go to next menu Cancel displayed item Select displayed item • Press t before entering your code.
Short Codes • Short Codes allow you to perform tasks easily. Enter your user code and then the short code for the task. • If your user code does not have the correct privileges, you may not be able to perform all these tasks. • If Not Allowed appears on your display your installer may not have allowed access to the tasks or your user code may not have the correct privileges.
Before You Begin • The step by step instructions on the following pages are the simplest way to perform the tasks. Please remember that your user code must have the correct privileges assigned to it to carry out the task. If it does not, contact your installer. • The system may have been set up in such a way that you will not have to do all the steps. For example, you may not always have to press the accept key . • Around 90% of alarms are false alarms.
Different Types of Arming • Arming means turning the system on. • There are several different ways of arming. Normal Set Turns on the entire system. Direct Arming This turns on the system without allowing an exit time. Your keypad cannot be in the guarded area. Partguard 1 This arms part of the premises but leaves unarmed some preprogrammed areas that you use. If you enter the secured area without turning off the alarm system an alarm will go off.
Arming with inhibited zones If a zone is open the alarm system cannot be switched on until the zone has been inhibited. This means that the zone, for example the kitchen, is left unguarded but the rest of the premises will be guarded. Only inhibit zones when absolutely necessary. If an open zone has the letter T in front of it on the display, it is a Tamper zone. This means that the alarm system itself has been tampered with in some way.
Turning on the Alarm System • This is known as ARMING. • Check that the premises are secure. • Go to the keypad. Press t+ user code CODE ACCEPTED ARM MENU Press uu NORMAL SET • • The buzzer will sound.
Direct Arming • Turns on the system without an exit time. • You should not be in the area to be guarded. • Go to the keypad.
Partguard 1 • This has been set up by your installer. • It arms part of the premises but leaves unarmed some areas you use. • Go to the keypad. Press t+ user code CODE ACCEPTED ARM MENU Press uv PARTGUARD 1 • • The buzzer will sound. You should remain in the unsecured part of the premises until the system is turned off.
Partguard 2 • This has been set up by your installer. • It arms part of the premises but leaves unarmed some areas you use. • Go to the keypad. Press t+ user code CODE ACCEPTED ARM MENU Press uw PARTGUARD 2 • • The buzzer will sound. You should remain in the unsecured part of the premises until the system is turned off.
Inhibiting Zones • Sometimes a fault can occur in your alarm system which leads to an Open Zone message on the display. • The system cannot be armed until all open zones are inhibited. SYSTEM ARMING OPEN ZONE(S) 03 HALL Press to start inhibiting INHIBIT ZONE ___ Press w(the number of the zone) 03 HALL IS INHIBITED SYSTEM ARMING LEAVE NOW SYSTEM ARMED Note:You must inhibit the open zones each time you turn on the alarm system until the fault is fixed.
Forced Arming • Forced Arming allows you to turn on the alarm system without inhibiting each open zone individually. • The open zones will be unguarded but the rest of your premises will be secure. • You should only do this when absolutely necessary as it leaves your premises less secure. • Zones cannot be inhibited if tampering has occurred.
Turning off the Alarm System • This is known as DISARMING. • Open the entry door. • The buzzer will sound. • Follow these steps.
What to Do After an Alarm • The Red LED on the Alarm Panel will be lit. Press t user code CODE ACCEPTED DISARM? Press SYSTEM DISARMED EVENTS IN LOG The Display scrolls through the incidents in all the zones.
Reading the Operator Log • The Operator Log stores up to 10 alarms and faults that occurred since the last arming. The first is the most recent. Press t+ user code CODE ACCEPTED ARM MENU Press z OPERATOR LOG To go down through Log press # ALARM G=8 Press t to get more details. 003THALL Press t to get the Date and Time SUN 03 MAR 23:33 Press when finished until you see FINISHED? • Press 18 to return to the original display.
Reading the Engineer Log • The Engineer Log can store up to 150 events. It is not deleted by an arming. Press t+ user code CODE ACCEPTED ARM MENU Press xu DISPLAY LOG Press to go through Log # ALARM G=8 Press t to get more details. 03THALL Press t to get the Date and Time SUN 03 MAR 23:33 Press when finished until you see FINISHED? • Press to return to the original display.
Changing the Time Press t+ user code CODE ACCEPTED ARM MENU Press xv TIME 12:23 Press Type the New Time uxvw Press • Press 20 to return to the original display.
Changing the Date Press t+ user code CODE ACCEPTED ARM MENU Press xw DATE 12/03/96 Press Type the New Date uvt{}z Press • Press CS450 User Manual to return to the original display.
Codes • The CS450 has 4 types of code • The code tells the system what rights you have. These are known as privileges. Permission to carry out tasks is linked to these privileges User Codes 8 of these can be assigned. Each user code will have a unique number. Duress Code This is used when you are forced to disarm the system unwillingly. The alarm system will be switched off. If you have a dialler connected a message will then be sent to the alarm company. Engineer Code This is used by the installer.
Code Rules Who can assign a Code? You must have the privilege Mg to create and delete other people’s codes. How many digits You must use 4 -6 digits. can be used? Can two codes A code must be unique have the same You cannot program a code numbers? which has the same first 4 digits as another code which contains those numbers. Example: If you have 1234 as a code you cannot create 12345 as a code.
Changing Your Code Press t+ user code CODE ACCEPTED ARM MENU Press ÎÊ CHANGE CODES CHANGE OWN CODE NEW CODE Type in New Code Press VERIFY Type in New Code Press • Press 24 to return to the original display.
Changing Other People’s Codes • There are 8 user codes. • This example changes the third user code Press + user code CODE ACCEPTED ARM MENU Press º¶ CHANGE CODES 01 CODE IN USE Press or 01 CODE UNUSED to scroll to code 03 CODE IN USE or 03 CODE UNUSED Press Type in New Code Press VERIFY Type in New Code Press • Press CS450 User Manual to return to the original display.
Setting Code 8 as a Temporary Code • Code 8 can be used as a temporary code. • This means that the code can only be used a set number of times. • The count can be set for between 1 and 98. • If code 8 is set to 0, it will not work. If it is set to 99 code 8 will work as a normal user code. • This example sets the count to 12. This means that code 8 can be used up to 12 times. Press t+ user code CODE ACCEPTED ARM MENU Press º¹ CODE COUNT 99 Press ¶· Press • Press 26 to return to the original display.
User Privileges • User privileges tell the alarm system which parts you can access. Your user code must have the correct privileges assigned to it to carry out the task. If it does not, contact your installer. • You can only assign privileges if you have the ‘Mg’ privilege. • It is not possible to assign privileges which you do not possess. Fs Ps Us In Mg User Privileges Turn on alarm system Turn on partguard 1 Turn on partguard 2 Turn off alarm system.
Changing User Privileges • This example adds Partguard Day and Partguard Night to User 5’s Privileges. Press t+ user code CODE ACCEPTED ARM MENU Press yw 1 MGINPSUSFS Press to get to User 5 5 Press 5 IN USFS to change the privileges IN USFS OK Press to scroll through the privileges Press 3 times to get to Ps 5 Press 5 IN USFS PS to add the Ps privilege IN PS USFS OK Press • Press 28 to return to the original display.
Testing the Bell Buzzer and Flashing Light • You can test if these are working from the keypad. Press t+ user code CODE ACCEPTED ARM MENU Press wv BELLTEST TIMING BELL TEST Beeep The bell buzzer and flashing light are tested BELL TEST • Press CS450 User Manual to return to the original display.
Turning on the Door Chime • A door can be programmed with a chime that sounds every time it opens. • This is set by the installer. • When the chime is on it is enabled. • When the chime is off it is disabled. • These steps let you turn it enable and disable the chime. Press t + user code CODE ACCEPTED ARM MENU Press wu CHIME ENABLED The chime was disabled but is now enabled Press to switch between ‘Chime Enabled’ and ‘Chime Disabled’ • Press 30 to return to the original display.
Using the Keyswitch • This is a mechanical switch which can turn the system on and off without a code. • Information on faults and alarms appears on the keypad. Turning on the Alarm System Go to the key switch. OK Check whether the “System OK” LED is on. If this LED is not on, check the keypad for a fault. The system can now arm. ON Turn the key switch to the ON position. Beeep The beeper begins to beep. The exit time has begun. Leave now. ON The “System ON” LED shows that the system is armed.
Turning off the Alarm System The entry period starts when you open the entrance door, or enter the entry zone. Beep Beep You can switch off the system without activating the alarm while the beeping continues. ON The “System ON” LED is on. The system is armed. Turn the key switch to the OFF position if your key switch has a OFF separate position for arming and disarming. The “System ON” LED is off. The OFF system is now disarmed.
Questions and Answers What do the LEDs mean? • There are three LEDs on your keypad. • This table shows what they mean and any action that needs to be taken when they are on. LED Purpose Action Green Mains power is on This LED should always be on. If it is not follow the steps for a mains failure Orange Fault in alarm system. Contact installer Red Check the logs Contact installer if necessary Alarm has occurred A mains failure has occurred.
1.Enter your code to turn off the beep. 2.If there is electricity elsewhere in the building check the fuse in the building’s fuse box. If this has blown replace the fuse and check again. 3. If the fuse in the switch box is working but the green LED is still off, contact the installer. The display shows ‘Not Allowed’ when I try and carry out a task • You have probably not been assigned the user privilege for that task. Contact the installer if you want the privilege.
1.How to turn the alarm system on and off. 2.The entrance and exit routes. 3.The number of the alarm company What do I do if there is a false alarm? • Disarm as usual. • Contact the alarm centre to which you are linked. My alarm won’t stop when I disarm the system • Try entering your code again. You may have entered it incorrectly. • If this does not work, someone may have cut the wire or there may be a problem with the control box. Contact your installer.
Glossary Armed Chime The alarm system is ON. An audible signal that a door has been opened. Code A series of 4-6 numbers that allow access to the system. Code Count A counter that can be set with code 8 to tell the system how many times the code can be used. Code Privileges assigned to a user code Privileges which tell the alarm system which parts the user can access. Direct Arm Turns on the alarm system without an exit time. Disarmed The alarm system is OFF. Display The window on the keypad.
Forced Arm Switches on the alarm system when a number of zones are open without inhibiting each one individually. Inhibited Zones that are left open when the Zones rest of the system is armed. They can be entered without triggering an alarm. KeySwitch A mechanical device that can turn the system on or off without a code. Operator Log A temporary log which contains all the alarms and faults between two armings. It is deleted after every arming.
Notes 38 CS450 User Manual
Notes CS450 User Manual 39
