Installation manual

ManualsBrandsAritronix ManualsConsumer electronicsScorpio

SR-i800

Motorcycle Security System

INSTALLATION MANUAL

AND USER’S GUIDE

Table of Contents

Installation

• Component List ---------------------------------------------------------------- Page 3

• Planning The Installation ---------------------------------------------------- Page 3

• Mounting The Components ----------------------------------------------- Page 4

• Color Codes --------------------------------------------------------------------- Page 5

• Connections --------------------------------------------------------------------- Page 5

• Using the T-tap ------------------------------------------------------------------ Page 6

User’s Guide

• Standard Features ------------------------------------------------------------ Page 2

• Transceiver Battery ------------------------------------------------------------ Page 3

• Violation Display --------------------------------------------------------------- Page 6

• Operating the transceiver -------------------------------------------------- Page 7

• Adjusting G Sensor ------------------------------------------------------------ Page 7

• Selecting Arming Modes ---------------------------------------------------- Page 7

• Alarm Triggers ------------------------------------------------------------------- Page 8

• Manual Override Code ----------------------------------------------------- Page 8

• Encoding a Transceiver ----------------------------------------------------- Page 1

• Troubleshooting Guide ------------------------------------------------------- Page 10

Accessories

• Optional Accessories ------------------------------------------------------ Page 2

• Perimeter Sensor (SN-5) ------------------------------------------------------ Page 9

Warranty and FCC Information

• Limited Warranty ------------------------------------------------------------- Page 11

• FCC Notice ---------------------------------------------------------------------- Page 11

• Contact information ---------------------------------------------------------- Page 11

Encoding a Transceiver

1. Unplug HAR-1 from the MCM-9 and plug it back in, the siren will chirp 2 times and

the lights will flash 2 times.

2. Within 6 seconds of plugging in the HAR-1, turn ignition switch “ON” and “OFF” 3

times.

3. If step 2 is done correctly and within the time allowed , the siren will chirp 2 times

and the lights will flash an additional 2 times to confirm that the system is in

“Learn Mode”.

4. Press and hold the button until the system chirps 2 times and the lights flash 2

times to indicate that the MCM has learned the code.

5. Turn ignition “ON” and “OFF” to exit “Learn Mode”.

**It is not recommended to clip the remote to your ignition key. Attaching the

remote to your key may damage the remote and/or scratch your bike**

Note:

The t

ransceivers a

re programmed from the factory.

Encoding

is only necessary should

the transceiver lose its code and will not arm or disarm the security system or if a

replacement remote is obtained.

Summary of content (6 pages)

PAGE 1
Table of Contents SR-i800 Motorcycle Security System INSTALLATION MANUAL AND USER’S GUIDE Installation • Component List ---------------------------------------------------------------• Planning The Installation ---------------------------------------------------• Mounting The Components ----------------------------------------------• Color Codes --------------------------------------------------------------------• Connections --------------------------------------------------------------------• Using the
PAGE 2
Components List MCM (Main Control Module) Standard Features • • • • • • • • • • • • • • • * Remote Transceiver Ultra low power drain MCM Built-in Analog Devices accelerometer Remote sensor control Battery safeguard with “sleep mode” Violation display Selectable auto/ manual arming / disarming Flashes signal lights Integrated 120 dB multi-tone siren Remote panic feature Soft chirp arming Three-Stage Perimeter Sensor Selectable Perimeter Sensor arming Flash input for diagnostics and possible future upgrade
PAGE 3
(Planning the Installation cont) Main Harness 1. 2. 3. 4. 5. 6. 7 Check that your motorcycle battery is fully charged and that all electrical circuits are in good working condition. Check the layout and construction of the motorcycle to decide what space is available to place the components. Verify that no moving parts interfere with the components or their wires. Do not route wires near sharp edges, which could cut wires and cause a short.
PAGE 4
Note: Connect the (HAR-1) harness to the MCM only after installation is completed. If the battery is to be removed, disconnect this connector first. Reconnect only after battery terminals are reconnected. Using the T-tap Connectors 1) Place female T-tap connector over wire to be tapped, close and squeeze until it snaps. 2) Now slip male T-tap connector over hinged end of the female connector. Motorcycle Wire 1) Operation Instructions (Cont.
PAGE 5
Perimeter Sensor (SN-5) Alarm Triggers 1. If bike is bumped, the siren will sound for 5 Seconds and the turn signal lights will flash. 2. If the bike is tilted, the siren will sound for 30 seconds and the turn signal lights will flash. 3. If the ignition switch is turned “on”, the siren will sound for 30 seconds and the turn signal lights will flash. Note: Once an alarm trigger has occurred and the siren duration is completed the system will remain armed and accept any additional triggers.
PAGE 6
Troubleshooting Guide Limited Warranty Limited Warranty Products manufactured by Aritronix, Ltd are warranted by the company to the original consumer purchaser to be free from defects in workmanship and materials.