User`s guide

ManualsBrandsAritronix ManualsConsumer electronicsScorpio

FCC Notice

This device complies with Part 15 of FCC rules.

Operation is subject to the following two

conditions: (1) This device may not cause

harmful interference, and (2) This device must

accept any interference that may cause

undesired operation.

Changes or modifications not expressly

approved by the party responsible for

compliance could void the user’s authority to

operate this device.

FCC ID: MKARI60

Fill this information for future use.

Date of purchase _____/_____/_____

Place of purchase _________________

_________________

Invoice/Receipt # _________________

Model Number _________________

Production Code _________________

Notes:

PECIAL NOTE ON RANGE

The average reception range is approximately ½ mile (800 meters). The actual reception range

could be greater or less depending on the location and/or the presence of obstacles between

the vehicle and the receiver. The reception range can also be affected by the presence of

stron

electroma

netic interference from outside sources.

ortant Information

Installation

User’s Guide

Tranceiver Information

tional Accessories

ppendix

Summary of content (14 pages)

PAGE 1
Important Information Fill this information for future use. FCC Notice Date of purchase This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference that may cause undesired operation.
PAGE 2
Table of Contents Limited Warranty Installation Component List Planning the Installation Installation Diagram Installation Warnings and Notes Mounting the Component Routing the Antenna Wire Making Connections Color Code Chart Using the T tap Connectors 3 3 4 5 5 5 5 6 6 User’s Guide Remote Transceiver Icons and Message Display Transceiver Charging Instructions Transceiver Battery Status Turning Transceiver On / Off Operating Instructions Arm Disarm Arming with SN-5 on Arming without siren 7 7 7 7 8 8 8
PAGE 3
Troubleshooting guide Problem Possible Cause Solution Key pad is locked Unlock key by holding button 4 for four seconds Power or ground not connected Verify connection to power lead and ground connection Turn signals will not flash Grey wires from GEN-1 not connected or connected to wrong wires Test wires and change connections to correct wires Perimeter Sensor not working Sensor not connected Check connections System activated with wrong button Activate with button 3 instead of button 1 Oran
PAGE 4
Installation Components TRS-6 Transceiver AC Adapter GEN-1 ACC-1 MCM-55 HAR-1 Planning the Installation Check that your motorcycle battery is fully charged. Check the layout of the motorcycle for placement of components. Verify that no moving parts interfere with the components or their wires. Verify that chosen location is not near extreme heat.
PAGE 5
--------------------- Installation Diagram -------------------Grey Wire ----- Turn Signal (+) Grey Wire ----- Turn Signal (+) Orange Wire ----- Tail light (+) Black Wire ----- Ground (-) To Battery (+) Optional SN-5 Dust Cap Perimeter Sensor Generic Connector Kit (GEN-1) Optional Main Harness (HAR-1) Accessory Harness (ACC-1) Igniton Disable RID-5 Factory Conenctor Kit To cut wire on bike * Antenna Main Control Module (MCM-55) 4
PAGE 6
Installation Warnings and Notes Ignition / Engine Control Wire Options: Note: Connect the (HAR-1) harness to the MCM only after installation is completed. Note: When the main harness (HAR-1) is plugged in, the siren should chirp. If the siren does not chirp; check the alarm inline fuse, connection to battery (+),and connection to ground (-). Note: If the battery is to be removed, disconnect HAR-1 connector first. Reconnect only after battery terminals are reconnected.
PAGE 7
Ignition Disable / Anti-hijack Module (RID-5) Installation 1. 2. Cut the Ignition / Engine control wire (refer to options) Attempt to start bike to test if correct wire is selected. If bike starts the wrong wire is selected. (contact Aritronix for assistance) If bike does not start, correct wire was selected continue to step 3. When packaged the RID-5 wire ends have been treated with clear silicon to protect the ends from fraying. Make sure they are stripped bare of this before continuing.
PAGE 8
Back-up Battery (BAT-5) User’s Guide Charging Instructions The transceiver is pre-charged at the factory and will operate out of the box; we recommend that the transceiver should be charged for at least 10 hours when first operated to insure full life of the battery. The back-up battery provides the system the ability to transmit information and activate the siren when power is interrupted. If power is ever interrupted while the system is activated the back-up battery will be engaged.
PAGE 9
Perimeter Sensor (SN-5) Operating Instructions The following instructions assume that the transceiver is within range of the motorcycle. Mounting the SN-5 The Perimeter sensor uses high frequency microwave technology to detect mass density movement around the motorcycle. The signal can transmit through the seat, fiberglass, leather and plastic, but not metal. It is recommended to place this sensor under the seat as close as possible to the center of the motorcycle.
PAGE 10
Programming and Customizing Instructions Entering Programming Mode 1) 3) Press button 4 Twice quickly to enter programming mode Press button 1 to select icon and to begin programming Programmable options will be displayed. The selected icon will flash Note. 2) Press button 4 to scroll trough programmable options Optional Accessories: At any time during programming press button 3 to exit without saving and return to the main screen Adjusting the Clock Time Enter the programming mode.
PAGE 11
Selecting Transceiver Alert Type (Audible/Silent/Vibrate) Enter programming mode. The icon will begin to flash, press button 1 to select. The LCD will display the current settings. To program follow these steps: Press button 4 to save and exit Press button 2 to scroll between the alert options Alert options include: alert off, vibrate, audible, vibrate and audible Selecting Auto/Manual Arming (proximity to MCM required) Enter the programming mode.
PAGE 12
Selecting Siren Tone and Alarm Duration (proximity to MCM required) Enter the programming mode. Scroll to the icon and press button 1 to select. The screen will display all of the sensor icons. To program follow these steps: Press button 1 to toggle between sound and duration settings Press button 1 to select sensor icon Press button 4 to scroll between the sensor icons Tone Press button 4 to save and exit Press button 2 to adjust selection Seconds Note.
PAGE 13
RCS (Range Confirmation Signal) If the transceiver is within range of the MCM and the alarm is activated then the LCD will display icon. Note: The transceivers are programmed from the factory. Encoding is only necessary should the transceiver lose its code and will not arm or disarm the security system or if a second or replacement remote is obtained. If the transceiver does not receive the RCS; the icon will not appear. 1.
PAGE 14
Transceiver Information Additional Information Sensor Memory Display When the system is disarmed the turn signals will flash to indicate if there has been an alarm trigger.