Installation Guide

ManualsBrandsArizona Shower Door ManualsShower DoorsES14876CHCLL

#6X3/8 Pan Head

Screw

ZV920-3

Center Guide

ZTE-1203

Wall Jamb

6 ZV-935

Screw Anchor

#8X1 1/4 Pan Head

Screw

ZV-924

Bumper

ZV-926

Bottom Bumper

#6/32X1/2 Machine

Screw

1 ZTE-1222

Curb

ZTE-1601

Header

ZV-918

Curb Vinyl

ETE/ESE-1/4

Model

# PicturePart #QtyDescription

To install your Shower Enclosure you will need

the following:

- Level

- 1/8" and 9/64" Drill Bits

- (Tile) 3/16" Masonry Bit

- Phillips Screwdriver

- Sealant

- Hack Saw

When ordering replacement parts, please

provide the following information:

1. Part Number

2. Part Name

3. Model Number

4. Specify design (if any)

INSTALLATION INSTRUCTIONS

ZA-99

Roller Wheel

4#8/32x3/8 CH

ASD24T

Towel Bar

ASD1

Pull Handle

Glass with 1/2" Holes

Glass with 7/8" Holes

Towel Bar

Pull Handle

ASD24R

ASD1R

Summary of content (7 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Model ETE/ESE-1/4 14 14 2 15 4 3 2 5 10 14 1 Wall Jamb 2 ZTE-1203 2 Screw Anchor 6 ZV-935 #8X1 1/4 Pan Head 6 Screw Bumper 4 2 ZV-924 Bottom Bumper ZV-926 4A 1 #6/32X1/2 Machine 2 Screw 6 Curb 1 ZTE-1222 7 Center Guide 1 ZV920-3 8 Header 1 ZTE-1601 3 3 1 5 2 6 9 4 12 7 3 1 When ordering replacement parts, please provide the following information: 1. Part Number 2. Part Name 3. Model Number 4.
PAGE 2
Arizona Corporate Office 2801 W. Indian School Rd Phoenix, AZ 85017 800-255-1901 PH 602-447-8208 FAX Florida 8100-1 Westside Industrial Dr Jacksonville, FL 32219 855-695-8899 PH 904-786-9025 FAX Illinois 2601 Bond St #1 University Park, IL 60484 800-861-6120 PH 708-235-0729 FAX Oregon 2057 Lars Way Medford.
PAGE 3
Installation Instructions for Model ETE-1/4/ESE-1/4 Note: These instructions will refer to the item #’s in the Exploded View drawing. For example, #1, #2, #3 etc… Please read through all of the instructions to get an over-view before you install the door. 1) Find the centerline of where the unit will be installed. This will usually be the center of the ledge of the bath tub or the curb of the shower pan. Place a centerline mark at each end of the tub ledge or curb where it meets the wall.
PAGE 4
the ZV924 Bumpers (#4) using the 2-#6/32X1/2 Machine screws (#5) keeping in mind that the inside panel will be on the showerhead side of the shower. 2) Measure the distance between the inside of the wall jambs (just above the tub ledge or curb). Measure tight and deduct 1/16” to 1/8” to get the cut size of the ZTE1222 Curb (#6) (E). Cut to size. Apply silicone where wall jambs meet tub or curb. Then run a bead along the underneath of the ZTE1222 Curb.
PAGE 5
until the top rollers can be guided up into the inside roller track of the header. Lift up glass then slowly lower the rollers into the inside roller track and let the panel hang in its vertical position. The outside panel will be installed the same way. Make sure the rollers are facing toward you. A helper would be valuable at this point to hold the inside panel on an angle toward the inside so that the outside panel can be lowered and positioned to be installed into the outside roller track.
PAGE 6
front edge of the ZTE1222 Curb. Position the guide just to the side of the panels, slip the front lip in, then snap the guide down over the inside of the curb. Slide the guide over carefully. When the doors are in a closed position the center guide should be centered in the overlap of the glass.
PAGE 7
*Towel bar and Pull Handle Addendum Due to design changes in the LETET, LESET, ETE, and ESE Series of bypass shower enclosures. There are now two separate types of pull handle and towel bars. The (ASD1) pull handle and the (ASD#T) towel bar are designed for glass with ½” holes. While the (ASD1R) pull handle and (ASD#R) towel bar are designed for glass with 7/8” holes. While ordering replacement parts please specify hole dimension.(1/2” or 7/8”).