Installation Guide

6 - ck
English
WARNING: Carry out the installation in a “workmanlike” manner, strictly following the installation instructions and using
suitable tools. Always consult your local building department for code requirements that must be respected depending
on its destination of use (private, secondary, public…).
Beforestartingtheassemblyprocess,unpackallcomponentsofthestaircase.Laythemoutonalargesurfaceand
checkthequantityofallthepieces,byconsultingthetable(TAB.1:A=Code,B=Quantity).
FortheUSAonly:callthecustomersupportlineat1-888STAIRKT,shouldyouhaveanycaseofneed.
Preliminary Assembly
1.
ScrewthepartsD32andD33intothetreads(L02)(g.2).
2. Carefullymeasuretheoor-to-oorheightanddeterminetherequirednumberofspacers(D03)(TAB.2).
3. Assemblethespacers(D14,D03,D02)togetherinonepiece.Dothesameforthespacers(D04,D03,D02)
(g.1).
4. AssemblethepartsC63,C65,C66intothebaluster(C03)(g.3).
5. AssemblethepartsB72,B73,B74,B78intothelandingE03,withouttightening(g.7).
6. AssemblethebaseG03,B17andB46(g.1).
Assembly
7. Determineandmarkontheoorthecentreofthehole,thenpositionthebase(G03+B17+B46)(g.4).
8. Drillwith14mm(⁄
”
)drillbitandxthebase(G03+B17+B46)intotheoorbymeansofthepartsB13(g.1).
9. Screwthepole(G02)intothebase(G03+B17+B46)(g.1).
10.Insertthespacers(D14+D03+D02)(g.5).
11.Insertthebaseplatecover(D05-D12)(g.5).
12.Insertthersttread(L02)intothepole(G02).Thencontinuewiththeassembly,byaddingalternativelyone
spacer(D04+D03+D02)andonetread(L02).Atthisstagewesuggesttopositionthetreadsalternatelyoneto
therightandonetotheleft,inordertodistributetheweightinabalancedway(g.5).
13.Whenyoureachtheendofthepole(G02),screwthepartB47onit,thenaddthesecondpole(G02)and
continuewiththestairassembly(g.5).
14.Whenyoureachtheendofthepole(G02),screwonitthepartB46andthepartG01.(ScrewthepartG01,until
itsupperendsticksoutapproximately15cm(5⁄
”
)fromthestairheight(g.6).Continueaddingthetreads,
byusingthepartD01insertedintothespacers(D04+D03+D02).
15.Finallyaddthestairlanding(E03).FastenthepartsB05,B04andscrewthepartB03sufciently(g.1)but
keepinginmindthatthetreadsstillhavetoberotatedtotheirnalpositionandthatthepointsAandBofthe
landing(E03)havetouchtheoor(g.8).
Fitting of the Landing
16.
ScrewthepartB71intotheelementB74,makingitruntilltheend.InsertthepartsB75,B76,B75-inthis
order–andthenagaintheelementB71,withouttighteningtoohard(g.7).
17.ApproachthepartB76totheceiling.Determinetheposition,thendrillwith14mm(⁄
”
)drillbitandx
completelybyusingthepartB58(g.7).
18.ScrewthelowerpartB71tillthepointsA,BandCtouchtheoor(g.8).
19.BlocktheupperpartB71onthepartB76(g.7).
20.Finally,blockthepartB73(g.7).
Assembly of the Railing
21.
Spread-outthetreads(L02)fan-like,afterhavingchosentherotationdirection.Thestairisnowreadytouse.
22. Startingfromthelanding(E03),insertthelongerrailingbalusters(C03-H1190mm-46 ⁄
”
),thatbuildthe
connectionbetweenthetreads.FacethemwiththepartC63showingthepartwiththeholesturnedupwards
(g.10).TightenonlythepartB02ofthelowertread(g.2).
23. CheckverycarefullytheverticalpositionoftheinsertedbalustersC03.Thiscontrolisveryimportantforinsuring
thebestresults.