English Français Español ASSEMBLY INSTRUCTIONS INSTRUCTIONS DE MONTAGE INSTRUCCIONES PARA EL ENSAMBLAJE
COD.5199 068076 ATTENTION: for the correct fixing of B20, turn the key around 90° from the contact point. A further additional rotation could damage the tread. ATTENTION : pour serrer correctement les vis B20, tourner le clef à environ 90° à partir du point de contact. Un ultérieur et inutile serrage pourrait endommager la marche. ATENCIÓN: para apretar correctamente los tornillos B20 es suficiente apretar la llave 90° desde el punto de contacto.
- kl
English WARNING: Carry out the installation in a “workmanlike” manner, strictly following the installation instructions and using suitable tools. Always consult your local building department for code requirements that must be respected depending on its destination of use (private, secondary, public…). Before starting the assembly process, unpack all components of the staircase. Lay them out on a large surface and check the quantity of all the pieces, by consulting the table TAB.1 (A = Code, B = Quantity).
obtain the same size as all others you assembled previously. 24. Fix into the floor in relation to the first baluster (C03) (H. 1190 mm - 46 7/8”), the part F01, by piercing with the 8 mm ( 5/16”) diameter bit. Use the parts C58, B12, B83 and B02 (fig. 1). Then assemble the reinforcing part (F07). 25. Find the handrail piece not marked in red colour (A13) and the one marked in red colour (A14) which will be used for the railing of the landing (E02) (fig. 9). 26.
Français ATTENTION : Effectuer l’installation dans les règles de l’art en utilisant des outils appropriés ; suivre scrupuleusement les instructions de montage. Pour réaliser un montage conforme aux normes en vigueur, il faut s’informer avant l’installation quant aux réglementations locales et nationales à respecter, en fonction du domaine d’utilisation (résidence privée principale, secondaire, bureaux, magasins,…). Avant de commencer le montage, il faut déballer tous les éléments de l’escalier.
23. Positionner la première colonnette (C03) (H. 1190 mm - 46 7/8”). Egaliser la longueur d’une colonnette longue (C03) (H. 1190 mm - 46 7/8”), en coupant l’extrémité, à la même longueur des autres colonnettes qui viennent d’être assemblés (fig. 1). 24. Fixer au sol, par rapport à la première colonnette (C03) (H. 1190 mm - 46 7/8”), l’élément F01, en perçant avec la mèche de diamètre 8 mm (5/16”). Employer les éléments C58, B12, B83 et B02 (fig. 1). Assembler l’élément de renfort (F07). 25.
Español CUIDADO: realizar la instalación "según las reglas del arte", utilizando herramientas adecuadas; seguir estrictamente las instrucciones de montaje. Informarse antes de la instalación sobre los reglamentos locales y nacionales a respetar, en función del destino de uso (privado principal, secundario, oficinas, tiendas…). Antes de empezar el ensamblado de la escalera, desembalar todas las piezas de la escalera. Colocarlas de manera que pueda verificarse las cantidades (TAB.
repitiendo las operaciones anteriores. 23. Colocar el primer barrote (C03) (H. 1190 mm - 46 7/8”). Adaptar la altura de un barrote largo (C03) (H. 1190 mm - 46 7/8”), cortando un extremo, a la altura de los barrotes recién ensamblados (fig. 1). 24. Fijar sobre el pavimento, coincidiendo con el primer barrote (C03) (H. 1190 mm - 46 7/8”), el elemento F01, taladrando con una broca de diámetro 8 mm (5/16”). Utilizar los elementos C58, B12, B83 y B02 (fig. 1). Montar el elemento de refuerzo (F07). 25.
TAB 1 B A A12 A13 A14 A15 B02 B03 B04 B05 B12 B13 B17 B20 B33 B46 B47 B82 B83 B95 C03 H. 1190 mm - 46 7/8” C03 H. 1130 mm - 44 1/2” C03 H. 1095 mm - 43 1/8” C03 H. 1060 mm - 41 3/4” C03 H.
- kl
English To determine the necessary number of spacers (D08), you must look-up the table TAB.2 (H = Height, A = Rises, X = quantity of spacers (D08) to position onto the spacer (D15), Y = quantity of the spacers (D08) to position onto the spacer (D14). Example: given a floor-to-floor height of 298 cm (9’ 9 3/8”) and a staircase with 13 treads, you must proceed as follows; 1. At height 298 cm (9’ 9 3/8” in the row H look-up the number of necessary spacers (X=6, Y=12, in the row A/13). 2.
TAB 2 - cm H A H 10 X 12 11 Y X H A Y X X A 14 13 Y Y H A 16 15 X Y 0 0 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 5 5 5 5 6 6 6 6 7 7 7 7 8 8 8 8 8 7 10 1 4 7 11 1 4 8 11 1 5 8 11 2 5 8 11 2 5 8 12 2 6 9 12 3 6 9 12 3 6 9 12 15 X Y X Y 0 0 0 1 1 1 1 1 2 2 2 2 2 3 3 3 3 4 4 4 4 4 5 5 5 5 6 6 6 6 6 7 7 7 7 7 8 8 8 8 5 9 12 14 4 7 10 13 2 5 9 12 15 4 7 10 13 2 5 9 12 15 4 7 10 12 2 5 9 12 14 4 7 9 10 12 5 9 12 15 KIT 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228
TAB 2 - in.
FIG.
FIG. 2 FIG. 3 FIG. 4 FIG. 5 FIG. 5 A FIG.
FIG.
FIG. 8 FIG. 9 FIG. 10 FIG. 11 FIG.
- kl
PRODUCT DETAILS English DONNÉES D’IDENTIFICATION DU PRODUIT Français DATOS DE IDENTIFICACIÓN Español
6 7 4 3 2 1 5
EN) product details trade name: KL type: spiral round plan staircase used materials STRUCTURE description composed of metal spacers (1) and plastic spacers (2) stacked and packed on the central modular pole (3) materials spacers: Fe 370 plastic spacers: ABS pole: Fe 370 galvanized finishing spacers: oven varnishing with epoxy powders TREADS description wooden circular treads (4) stacked on the central pole (3) materials beech finishing colour: water-base undercoat: water-base finishing: water-base RAILIN
FR) données d’identification du produit denomination commerciale : KL typologie : escalier helicoïdal à plan rond materiaux utilisés STRUCTURE description composé de entretoises (1) en métal et cales (2) en plastique empilées et comprimées sur le pylône (3) modulaire central materiaux entretoises : Fe 370 cales : ABS pylône : Fe 370 galvanisé finition cales : vernissage à chaud avec poudres époxy MARCHES description marches (4) en bois circulaires empilees sur le pylône (3) central materiaux hêtre finit
ES) datos de identificación del producto denominación comercial: KL tipo: escalera de caracol de planta redonda materiales empleados ESTRUCTURA descripción compuesta por distanciadores (1) de metal y espaciadores (2) de plástico enfilados y comprimidos en la columna (3) central modular materiales distanciadores: Fe 370 espaciadores: ABS palo: Fe 370 galvanizado acabado distanciadores: barnizado en horno con polvos epoxídicos.
www.arkestairs.com KL www.arkestairs.com arkè by Fontanot S.p.A. 75 Jackson Street, Suite 100 Newnan, GA 30263 tel. +39.0541.90.61.11 fax +39.0541.90.61.24 info@arkestairs.com www.arkestairs.com cod. 065298000 D.U.