User's Manual

ADH300J
FEATURES
COMPATIBLE WITH VARIOUS DEVICES
TROUBLESHOOTING
TECHNICAL SPECIFICATIONS
ABOUT ARTISTE
PACKAGE CONTENTS FUNCTION IDENTIFICATION INSTALLATION AND OPERATION
OUTPUT JACK OPTIONS
Television Smartphone Computer Tablet Radio Set-top Box Laptop
1. 30 Meters Wireless Transmission Range
2. 15~20 Hours Working Duration
3. 2.4GHz Digital Wireless Technology
4. One Transmitter can be connected to Several Headphones
TV
FM
Optical
OUT
AUX/3.5mm
RCA jacks
labeled
“AUDIO OUT”
Other RCA
jacks
(usually audio IN)
① Wireless Headphone
② Transmitter/Charging Base
③ 3.5mm to 3.5mm Direct Line-In cable
④ Rechargeable Battery*2
(Installed in Headphone)
⑤ AC/DC Adaptor
⑥ 3.5mm to RCA Cable
⑦ Optical TOSLINK Audio Cable
⑧ User Manual
①
②
■ No sound
- Ensure that the Transmitter power ON.
- Ensure that the Headphone is ON, Red LED Indicator is in solid red.
- The charge level of the Batteries may be too low. Recharge the Batteries.
- Audio device is ON and PLAY.
- The volume of headphone may be too low, adjust the volume to a moderate level.
The audio signal input level is too low. Increase the volume of the audio device.
- Ensure the volume level of Headphone is set to an approximate level.
- The Headphone is too far from the Transmitter, move it closer.
- The audio signal input level is too low. Increase the volume of the audio device.
CAUTION
To protect your hearing, please do not use the headphone at high volume for a
long time.
Wireless transmission will produce electromagnetic signal which may interfere
the heart pacemaker or other medical instruments properly function.
Please follow your doctor’s instruction.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one of the following measures:�
- �Reorient or relocate the receiving antenna.�
- �Increase the separation between the equipment and receiver.�
- �Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.�
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The
device can be usedin portable exposure condition without restriction.
�
Transmission Mode: GFSK Carrier Frequency: 2.4GHz
Operating Voltage: Transmitter/Charger DC 5V 550mA
Headphone 2*1.2V AAA
Frequency Response: 25Hz~20KHz Distortion: ＜0.5%
S/N Ratio: ＞70dB Operating Distance: 30 meters
Music Time: 15~20 hours Charge Time: 5~7 hours
ARTISTE TECHNOLOGY LTD.
The 6th Building, No. 173, Dunhe Road,
Haizhu District, Guangzhou, Guangdong, China
www.artiste-audio.com
Tel: [phone]
Made In China
① 3.5mm Audio IN Socket
② Optical TOSLINK Audio IN Socket
③ DC IN Socket
■Wireless Headphone
■Transmitter
■ CHARGING THE BATTERIES
■ Optical input (recommended)
■ Analogue audio input
NOTE:
Please note that only one input (either analogue audio input or optical input/TOSLINK) must be
connected. If both the analogue audio input and the optical input/TOSLINK are connected,
the priority use is analogue input.
Charge the Batteries for about 7 hours before first use.
Charging Duration: 5~7 Hours
① Turn OFF the Headphone.
② Retract the Headband.
③ Place the Headphone
on the Transmitter.
■ AUTO OFF
■ Reconnect/Connect more Headphones
■ Distortion
- Transmitter will be OFF automatically if there is no audio source signal for around
3 minutes. If the audio source signal returns, the transmitter will automatically
switches ON.
- Headphone will be OFF automatically if there is no audio source signal for around
3 minutes.
Charging Green LED Indicator
（Solid Green: charging/
Light out: fully charged）
Signal Red LED Indicator
Charging Green LED Indicator
（Solid Green: charging/
Light out: fully charged）
Signal Red LED Indicator
（Solid Red: connect/
Flash: pairing）
Signal link Green LED Indicator
(Solid Green: connected)
(Flash: pairing)
(Flash Quickly: connect new
headphone/reconnect)
Power Red LED Indicator
(Solid Red: ON)
(Light out: OFF)
ON/OFF Control (press 2 seconds: ON/OFF)
(press 5 seconds when OFF:
connect new headphone/reconnect)
① ② ③
Red LED Indicator
Green LED Indicator
Charging Contacts
ON/OFF
Red LED Indicator
Green LED
Indicator
Volume +/-
① Disconnect the power of Transmitter.
② Turn OFF the Headphone. Press ON/OFF control for 5 seconds
until the Green LED flashes quickly.
③ Connect the power of Transmitter.
④ Headphone and Transmitter will be connected automatically.
Red LED Indicator
Green LED Indicator
P9 P10 P11 P12 P13 P14 P15 P16
AUDIO
IN
OPTICAL DC IN
③
④
⑤
⑥
⑦
⑧
WARNING: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
The device must not be co-located or operating in conjunction with any other
antenna or transmitter.
This device complies with FCC’s radiation exposure limits set forth for an
uncontrolled environment