Assembly&Instruction Manual 10x12ft ergola Installation Guide 12ft 10ft Save this manual for future reference
INTRODUCTION Thank you for purchasing Aoodor's Patio pergola! We hope you will find joy in our product for many years to come. To ensure your personal safety during installation and to get the most out of your investment, please read this entire manual before beginning the installation process. If you feel that this process is too difficult to do on your own, we advise that you seek assistance from a local building or home improvement contractor.
Parts list Par ts Desc Qty Ref No Par ts A1 4 800 - 044 - 001 A2 2 B2 Desc Qty Ref No I 1 800-044-020 800 - 044 - 002 I1 2 800 - 044-021 2 800 - 044-003 J 16 800 - 044-022 C1 1 800-044-004 K 16 800-044-023 C2 1 800-044-005 L 4 800-044-024 D 2 800-044-006 M 8 800-044-025 S1 2 800-044-007 N 1 800-044-026 S2 2 800-044-008 O 6 800-044-027 E1 1 800-044-009 P 32 800-044-028 E2 1 800-044-010 Q 2 800 - 044 - 029 F1 2 800-044-011 R 20 800-044-0
Assembly 1 K x16 R C x1 D x1 E x1 S x2 F x2 x16 Step1:Beam assembly. 1.Connect (C1) with (C2) together using screw(K) tightly to became Side Beam(C) 2.Connect (D) to (D) with connector(AE) together using screw(K) tightly to became Middle Cross Beam(D) 3.Connect (E1) with (E2) together using screw(K) tightly to became Side Beam(E) 4.Connect (S1) with (S2) together using screw(R) tightly to became Cross Beam(S) 5.
Assembly 2 x1 N x1 L x4 I x1 V x2 Step2:Middle cross beam assembly Insert the Hook pulley as the figure shown above.(N)x1,(L)x3,(I)x1. And cover the beam cap(V). 3 x2 M x8 I1 x2 V x4 I1 Step3:Cross beam assembly Insert the Hook pulley (M) And cover the beam cap. Note:Repeat this step for whole Beam(F). 4 A1 B2 B W T A2 A1 A W x4 T x2 x2 x4 A1 Step4:Post assembly 1.connect post(A1) to post(B2) with connector(T) and using bolt (R) ,become Post(B) 2.
Assembly 5 P x16 V x4 x1 Step5:Post and Side Beam assembly 1.Connect Post (B) and Post(A) to beam ( C）using bolt(P) 2.Connect Post (B) and Post(A) to beam ( E）using bolt(P) Note:Repeat this step for all posts and beams. 3.Cover the beam cap(V).
Assembly 6 Fig . 6 . 1 Fig . 6 . 1 J Fig . 6 . 3 H1 Q Fig . 6 . 2 P x16 J x8 R x4 Q x2 x1 Step6:Post and Cross Beam assembly 1.Connect Post (B) and Post(A) to Cross beam ( F）using bolt(P),see fig.6.1 Note:Repeat this step for all Cross beam (F). 2.Inser t the post mount to the post and fix with bolt ( R ). see fig . 6 . 2 3.Connect the suppor t bar(H1)together using bolt(Q).see fig.6.3 4.Install the support bar(H1) to post(A)and post (B)using bolt (J).
Assembly 7 Fig.7.1 Fig.7.2 O x4 V x4 x1 Step7:Cross Beam assembly 1.Attach Cross beam (S) to the Side beam (C)and (E) and fix with bolt(O),see Fig.7.1 and Fig.7.2 2.Cover the beam cap(V) Note:Repeat this step for all Cross beam (S).
Assembly 8 Fig.8.3 Fig.8.4 Fig.8.1 Fig.8.2 Step8:Fabric roof assembly. 1.Inser t the Pole (H)and (G) through the fabric. 2.Inser t the pole(H) through the pulley(I) and fabric (U).see Fig.8.1 and connect the pole(H) together.see Fig.8.2 3.Inser t the pole(G) through the pulley(N) and fabric (U).see Fig.8.3 and connect the pole(H) together.see Fig.8.4. 9 J x4 AD x4 Step9:Cur tain install 1.Attach the bracket(AD) to the cur tain(H2) using bolt(J).
Assembly 10 Fig.10.1 Fig.10.1 Fig.10.2 O x2 J x4 Step10:Roof install. 1.Attach Middle Cross beam (D) to the Side beam (C)and (E) and fix with bolt(O),see Fig.10.1 2.Attache the cur tain(H2) to beam(C),and using bolt (J).see Fig.10.
Assembly 11 Fig.11.1 Fig.11.1 X Step11:Roof install. 1.Fasten the tube(G) to the beam(C),and using bolt (X).see Fig.11.
Assembly 11 I1 Fig.12.3 Fig.12.1 Hard ground M Fig.12.2 Soft ground Step12:Fabric assembly 1.Turn the bolt out from pole (H) see Fig.12.1and inser t the pole through the pulley hook(M) ,then turn bolt in.Fig.12.2 Note:Repeat this step for all poles. 2.Turn the plastic bolt cap to fix the roof.see Fig.12.
