User Manual
Table Of Contents
- 1. Get to Know Your Ultra 2 Camera
- 2. Get Started
- Use the Arlo app for installation and setup
- Connect your SmartHub to the Internet
- Connect a Base Station with Siren
- Insert the battery into your camera
- The camera battery
- The Arlo Ultra Camera LED
- Tips for optimal WiFi performance
- Magnetic mount
- Install the Arlo Outdoor Mount
- Install an Anti-Theft Mount
- Connect your camera to the Arlo solar panel (sold separately)
- Your Arlo Ultra camera’s field of view
- Position your camera to detect motion in specific areas
- Test motion detection
- Arm your camera to detect motion
- 3. Arlo Ultra Basics
- 4. Access your Arlo account
- 5. Ultra Image Quality Features
- 6. Modes, Rules, and Alerts
- Modes
- Select a mode
- Mute Notifications
- Rules for modes
- Change motion sensitivity
- Automatically stop recording when motion stops
- Control whether the spotlight turns on when motion is detected at night
- Change audio sensitivity
- Add a rule with a base station siren trigger
- Manage alerts
- Schedule your camera rules
- Set up Arlo Geofencing
- Geofencing with multiple mobile devices
- Custom modes
- Detect audio alarms with your Ultra camera
- 7. Change Your Arlo Settings
- 8. Use SD Card Storage
- 9. USB Storage
- 10. Arlo Connect
- 11. FAQs and Troubleshooting
- FAQs
- Battery FAQs
- The Arlo app doesn’t recognize my device
- Troubleshoot two-step verification
- Activity zones and CVR aren’t working
- Troubleshoot Arlo Geofencing
- Can’t see video streams in a browser
- WiFi signal interference
- Not receiving push notification alerts
- Arlo Smart Alarm Detection isn’t working
- Verify that the SmartHub or base station is online
- The SmartHub or base station is offline
- Reset the SmartHub to factory settings
- Reset a Base Station to factory settings
- 12. Rechargeable Battery Safety
85FAQs and Troubleshooting
Ultra Series 4K UHD Wire-Free Security Camera System
User Manual
3. Make sure that the Show Notications setting is selected.
If you said no to push notifications at installation
When you install the Arlo app for the rst time, to receive alerts, you must select Allow when
asked if you want Arlo to send you push notications. For iOS apps, aer you respond to this
alert, it isn’t presented again unless the device is restored to factory settings or the app is
uninstalled for at least a day.
If you said no on an iOS device, uninstall the app, wait for a day, and then reinstall it, and
allow notications. If you don’t want to wait a day before you reinstall the app, you can use
the system clock on your device to simulate a day. Set the system clock forward a day or
more, turn your device o, and then turn the device back on. Aer you reinstall the app, return
the system clock to the correct setting.
Arlo Smart Alarm Detection isn’t working
Alarm detection noties you in your Arlo app when a smoke or carbon monoxide (CO)
detector’s alarm is activated. You need an Arlo Smart subscription to use this feature (see
Detect audio alarms with your Ultra camera on page 53).
Your camera might not detect an alarm in the following situations:
• Your alarm doesn’t emit a T3 or T4 alarm pattern.
• Multiple overlapping alarms occur.
• Echoes occur in the alarm location.
• Another noise is equal to, or louder than, the alarm.
Verify that the SmartHub or base station is
online
To determine whether your SmartHub is online, check the LED on the front of the SmartHub
or Base Station with Siren:
For a SmartHub or for a Base Station with Siren VMB4500:
• If the LED is solid blue, the SmartHub or base station is connected to the Internet.
• If the LED is amber, the SmartHub or base station isn’t connected to the Internet.
For Base Station with Siren VMB4000, check the
Internet LED:
• If the Internet LED is green, the base station is connected to the Internet.