Warranty

LED Cabinet Down Light
Architectural quality, component-based LED lighting system
Models QEV3W-WW and QEV3W-NW
Practical configuration, easy to install
Highly configurable to meet the custom design needs of homeowners and lighting
professionals. Easily extend cables to meet installation needs. Install individually
or together in series, limited only by the output rating of the power supply.
Bright and highly efficient, cool to the touch
LEDs emit very little heat, ensuring they won’t overheat an enclosed space.
Integral diffusers soften the lighting and reduce glare on adjacent surfaces. High-
quality, energy-efficient LEDs are rated for 50,000 hours and require a 12V DC
power supply (sold separately) with enough wattage to suit the application.
Fully dimmable
Use only with Armacost Lighting’s 12V DC low voltage LED dimmers
or an Armacost hardwired AC to DC dimmable LED power supply
with a compatible Lutron
®
or similar style in-wall AC dimmer. Visit
armacostlighting.com/dimming to learn more about the types of dimmers
that will work with this LED down light.
Works with other Armacost component-based lighting
LED Cabinet Down Lights can be linked together or combined in the same
12V low voltage circuit with other Armacost lighting products, including white
RibbonFlex Pro
®
LED tape lighting and 1 watt Mini Recessed Accent LED Lights.
Requires a 12V DC power supply. Each LED cabinet down light uses
about 3.2 watts. Choose an adequately rated power supply based on the
number of installed lights.
IMPORTANT
CAUTION: For use only with low voltage 12V DC power source.
Do not connect to 120V AC current.
For dry location only.
Disconnect all power before installing.
Wire runs inside walls must be installed in accordance with national and local
electrical codes, low voltage Class 2 circuit. Use properly certified CL2 or better
cabling. Do not install low-voltage wiring in the same wire run as AC power.
If AC and low-voltage wires cross, keep them at 90-degree angles. If you are
unclear as to how to install and wire this device, contact a qualified electrician.

Use only insulated staples, plastic ties or clips to secure wires.

Route and secure wires so they will not be pinched or damaged.

Failure to observe polarity or shorting of wires may damage the LED lights.
INSTALLATION GUIDELINES
First, remove trim ring by grasping ring and then firmly pushing on back
side of LED light.
Flush mount
Cut a 2.5" diameter hole at desired location and
insert light. Tension clips will hold the light in
place. No trim ring required.
Surface mount
Keeping power cable
threaded through trim ring,
install ring using supplied
screws. Insert light into
trim ring until secure.
Connect multiple LED Cabinet Down Lights
Link multiple LED down lights together by simply plugging one light into
another. Each light comes with a 36" color coded (+/-) 2-conductor power
cable with two pre-installed connectors to allow for various configurations.
If further separation between each light is required (more than the installed
cables will allow), simply cut the cable and splice together additional longer
wires as needed. 18 AWG cable is recommended.
Be sure to use a 12V DC power supply with sufficient wattage to power the
total number of LED lights connected to your system. At 100% brightness,
each LED light uses about 3.24 watts or 0.27 amps.
12V DC
POWER
SUPPLY
DOWN
LIGHT
DOWN
LIGHT
DOWN
LIGHT
Connect to 12V DC power supply
LED Cabinet Down Lights are supplied with a separate 6" power plug
connector. This connector is designed to fit in either a male or female
connector, both of which are found on the LED light power cable. Connect
power plug to any available down light connector, cut off extra plastic
connector not being used on the power plug, strip wires and connect to your
12V DC power supply. Be sure to maintain polarity. Red is positive, black is
negative (+ to +, – to –). Connect wires to power supply using a terminal block,
wire nuts, crimp connectors, soldering wires, etc. For interior RV and boat
applications, this LED light can be powered directly by 12V battery.
armacostlighting.com
140 Baltic Avenue, Baltimore, MD 21225
© 2013-15 Armacost Lighting. All rights reserved.
141203
SPECIFICATIONS WARM WHITE NATURAL WHITE
Input Voltage 12V DC 12V DC
Power Consumption ~3.2W ~3.2W
Color Temperature Option ~2700K ~4000K
Light Output (Lumens) 240 280
Lumens per Watt (Efficacy) 80 93
Color Accuracy (CRI) 83 83
LED Count 1W x 3 1W x 3
Beam Angle 60 60
Limited 3-year warranty. This product is for dry location use only.
Improper installation, improper powering, abuse, or failure to use this
product for its intended purpose will void warranty. Proof of purchase is
required for all returns. Questions? Email [e-mail].
Feed power cable
through cabinet
surface or through
notch in trim ring
12V DC
POWER
SUPPLY
Output:
12V DC
Power Plug
Connector
TO LED
LIGHTING
Cut off plastic plug
not being used
(Black)
–
+
(Red)
(Black)
–
+
(Red)
Trim
ring