Installation Guide

2-in-1 LED Dimmer
–
Wireless Ready
Model # DIM2IN1-RF-WR
■
Provides full range brightness control of low
voltage white LED lighting.
■
Use dimmer alone or with Armacost Lighting’s
optional designer-style wireless touchpad dimmer
for remote 2-way lighting control.
■
Unique convertible design installs directly into
standard switch box or surface mounts anywhere
for easy, precise control of your LED lighting.
■
Works with both 12V DC and 24V DC LED lighting.
■
Dimming will save energy and extend LED life.
INSTALLATION GUIDELINES
■
For use only with 12V DC or 24V DC low voltage
single color LED lighting. Do not connect this device
to 120V AC current. For dry location use. If used
outdoors, unit must be installed inside wet location
rated electrical box enclosure.
■
Do not connect more than one dimmer to a power
supply in the same circuit. Doing so will cause the
LED lights to fl icker.
■
Use only with 12V or 24V DC constant voltage
standard electronic power supplies. Not compatible
with magnetic power supplies or low voltage power
supplies with 12V AC output.
■
Suitable for RV and boat interior applications
(dry location), this device can be direct wired and
powered by an on-board 12 or 24V battery.
■
Do not exceed 96 watts of lighting when used with
12V LEDs or 192 watts when used with 24V LEDs.
■
All wiring must be in accordance with national and
local electrical codes, low voltage Class 2 circuit.
If you are unclear as to how to install and wire this
product, contact a qualifi ed electrician.
■
Be sure to maintain polarity (+ to +, – to –).
Failure to observe polarity or shorting of wires
may damage the dimmer.
Maintain +/– polarity
12-24V DC
input (from
low voltage
output on
power supply)
12-24V
DC output
(connect to
LED lighting)
■
Use only insulated staples or plastic ties to secure
cords and wires.
■
Route and secure wires so they will not be
pinched or damaged.
■
For wire runs inside of walls, use certifi ed CL2 or
better cabling and appropriate mounting hardware.
■
Do not install Class 2 low voltage wiring in the
same runs as AC main power. If AC and low voltage
wires cross, keep them at 90-degree angles.
LED TAPE LIGHT
LED DOWN LIGHTS
12 or 24V DC
Plug in or
direct wire
STANDARD ELECTRONIC
DC OUTPUT POWER SUPPLY
2-IN-1
LED DIMMER
120V AC
12 or 24V DC
OPTIONAL WIRELESS
DIMMER REMOTE
(Model DIM14REM)
© 2012-15 Armacost Lighting. All rights reserved. 150904
To convert dimmer
for in-wall installation
Carefully remove rotary knob and install insert plate on
top of dimmer as shown. Secure with washer and hex
nut. Dimmer can now be mounted into standard switch
box. Finish by installing designer-style switch cover plate
(sold separately at most home improvement stores).
Installation tips:
■
When dimmer
is installed in
smaller electrical
boxes, create more
space for wires
by removing top
mounting tab.
■
Remove green quick
connect terminal
block for easier wire
routing. Route wires with terminal block then snap
terminal block back into dimmer. Observe the polarity
printed on the dimmer case and maintain same
sequence on terminal block while securing wires.
For better LED brightness,
keep voltage drop to a minimum
Voltage drop is a natural occurrence in all low voltage
lighting systems. It is the gradual decrease in voltage
that occurs from your power supply to your LED lighting.
Voltage drop only becomes undesirable if you notice the
brightness in one area of your lighting is objectionably
different than another area. As a practical approach
to installing LED lights, test your lighting prior to fi nal
installation. If voltage drop appears to be a concern, use
shorter lengths of DC power feed wires or switch to a
thicker gauge wire (lower AWG number).
For an online voltage drop calculator, visit
armacostlighting.com/installation.
Insert plate
This tab can be removed when
installing in smaller box
Wireless Touchpad
(Model No. DIM14REM)
Designer-style switch plate and all
mounting screws included.
■
Beautifully blends with existing designer
switches and dimming décor.
■
Provides full range dimming – works up
to 100 feet away through walls and doors.
■
Convenient 2-way lighting control – works
in unison with your existing dimmer.
■
RF pairing technology offers ease of expand-
ability without having to run extra wiring
■
Can control multiple 2-in-1 LED dimmers with
a single touchpad. Touchpads can also be
paired with dimmers to control lighting zones
in the same area without interference.
■
Compatible only with the Wireless Ready
dimmer (Model DIM2IN1-RF-WR)
SPECIFICATIONS
Input voltage .............................................................. 12V-24V DC
Output current..........................................................................8A
Max load with 12V DC lighting .......................................... 96 watts
Max load with 24V DC lighting ........................................ 192 watts
Working temperature ............................... -5 to 120°F (-20 to 49°C)
Country of origin .................................................................. China
Limited 1-year warranty. Improper
installation, improper powering,
abuse, or failure to use this device
for its intended purpose will void
warranty. Proof of purchase is
required for all returns. Questions?
Email [e-mail].
Easily surface
mounts using
screw down tabs.
Or install in wall
using supplied
insert plate.
OPTIONAL ACCESSORY
To buy online, or
to learn more, visit
armacostlighting.com/dimmers
Surface mount
Easily mount to any
wall or fl at surface,
no hole required.
Install in wall
Can be installed
in wall in an
electrical box.