TDS

RECOMMENDED FILM THICKNESS
COVERAGE
PRIMERS
TOPCOAT
FEATURES
SOLIDS BY WEIGHT
LIMITATIONS
PRODUCT DESCRIPTION
ARM015X is a two component water based epoxy coating that exhibits excellent characteristics that rival solvent based
products. ARM015X has superb chemical resistance, abrasion resistance, and substrate penetration.
RECOMMENDED FOR: priming or coating concrete, wood or masonry. This product can be used as a standalone coating,
as a primer for additional epoxy layers, and to assist with moisture blocking for epoxy systems. Can withstand exposure to
many common solvents and chemicals.
ARM015X
ARMORULTRA PRIMER
TECHNICAL DATA SHEET
Color or gloss may be affected by humidity, low temperatures, chemical exposure or sodium vapor lighting. Product will yellow in the presence of UV light.
For best results use a 1/4” or 3/8” nap roller. Slab on grade requires moisture barrier Substrate temperature must be 5°F above dew point. All new concrete
must be cured for at least 30 days Product color will vary from batch to batch. Use only product from the same batch for an entire job. Improper mixing or
too thick of an application may result in product failure. Light or bright colors (white, safety colors etc.) may require multiple coats or a topcoat to achieve a
satisfactory hide, depending on the substrate. Physical properties listed on this technical data sheet are typical values and not specifications. See reverse
side for limitations of our liability and warranty. See reverse side for application instructions.
PRIMER
High Performance Epoxy
Rev 11/21
SOLIDS BY VOLUME
DOT CLASSIFICATIONS
PACKAGING INFORMATION
SHELF LIFE
FINISH CHARACTERISTICS
IMPACT RESISTANCE
Mixed = 53% (colors); 45% (clear); (+, - 2%)
Mixed = 41% (colors); 36% (clear); (+, - 2%)
Not regulated
5 -7 mils per coat wet thickness (yields 2-3 mils dry)
2 gallon and 5 gallon kits (volume approx.)
1 year in unopened containers
Satin gloss (40-80 at 60 degrees @ glossmeter)
Gardner Impact, direct = 50 in.lb. (passed)
No cracks on a 1/8” mandrel
FLEXIBILITY
VISCOSITY
VOLATILE ORGANIC
CONTENT
Mixed = 900-1200 cps (colors); 400-900 cps (clear) (typical)
Colors = 1.01 pounds per gallon (mixed)
(regulatory VOC = 175g/l) Clear = 1.0 pounds per
gallon (mixed) (regulatory VOC = 230g/l)
ADHESION
425 psi @ elcometer (concrete failure, no delamination)
Taber adrasor CS-17 calibrase wheel with 1000
gram total load and 500 cycles = 54 mg loss
ABRASION RESISTANCE
PER GALLON
229 to 320 square feet @ 5-7 mils wet thickness
COLORS
CURE SCHEDULE
TACK FREE (Dry to touch)
RECOAT OR TOPCOAT
5-8 hours
7-10 hours
16-24 hours
LIGHT FOOT TRAFFIC
APPLICATION TEMPERATURE
55-90 degrees F with relative humidity
below 75%
FULL CURE (heavy traffic)
2-7 days
CHEMICAL RESISTANCE
MEK
Gasoline
10% Sodium Hydroxide
50% Sodium Hydroxide
10% Sulfuric
10% Hydrochloric Acid
20% Nitric Acid
Ethylene Glycol
SPECS
Acetic Acid 5%
Xylene
B
A
B
C
B
B
B
A
C
Off white, light gray, medium gray, tile red, beige, and amber clear.
NOTE: The clear (gardner 11) is not water clear and is not suitable
for topcoating over previously color coated floors. The clear is
suitable as a primer or concrete sealer only.
None required
Optional – Many products are suitable as topcoats including multiple
coats of this product. For added chemical resistance, color stability or
UV stability, use with build coat ARM707X and/or topcoat such as
ARM321X
Concrete/Wood/
Masonry
Multiple
Colors
Super
Durable
Easy to
Install
Roll On
Application
MIX RATIO
4 Parts A to 1 Pat B
POT LIFE (1 gal volume)
1-1.5 hours
B
Rating Key: Rating key: A - not recommended, B - 2 hour term splash spill, C - 8
hour term splash spill, D - 72 hour immersion, E - long term immersion. NOTE:
extensive chemical resistance information is available through your sales
representative.
ArmorPoxy Inc.
1260 North Ave
Plainfield, NJ 07062
armorpoxy.com
E: [e-mail]
P: 888-755-7361