TDS

20% Nitric Acid
PRODUCT DESCRIPTION
ARM356X is a one component moisture cured polyurethane (HDI based) floor coating/sealer that exhibits superior
characteristics for abrasion resistance and chemical resistance. This product has good UV stability.
RECOMMENDED FOR: Recommended for showrooms, garage floors, warehouses, laboratories, cafeterias, and most
indoor chemical exposure areas with regard to concrete or cement.
RECOMMENDED FILM THICKNESS
COVERAGE
PRIMERS
TOPCOAT
FEATURES
SOLIDS BY WEIGHT
LIMITATIONS
ARM356X
ARMORULTRA HIGH PERFORMACE MILITARY
GRADE 1 PART TOPCOAT
TECHNICAL DATA SHEET
Clarity, gloss or color may be affected by high humidity, low temperatures, chemical exposure, tire contact or exposure to lighting such as sodium vapor lights. For best results use a
high quality 3/8” nap roller. Slab on grade requires moisture barrier. Substrate temperature must be 5°F above dew point. All new concrete must be cured for at least 30 days. Use a
suitable primer If recoating after 24 hours, then the surface must be deglossed before the application. Surface irregularities are possible over smooth basecoats and re-coats. Contact
your sales associate for recommendations. The concrete and joints must be thoroughly dry prior to application. Applying the product thicker than recommended may result in
product failure. Applications in direct sunlight, high humidity or high temperatures may cause surface curing before suitable air release has occurred. Physical properties are typical
values and not specifications. See reverse side for application instructions. See reverse side for limitations of our liability and warranty
TOCPOAT
One Part Urethane
Rev 11/21
SOLIDS BY VOLUME
VOLATILE ORGANIC CONTENT
PACKAGING INFORMATION
SHELF LIFE
FINISH CHARACTERISTICS
IMPACT RESISTANCE
65% (+/- 3%)
60% (+/- 3%)
Less than 329 g/l
3-5 mils per coat wet thickness
1 gallon, 5 gallon and 55 gallon containers
3 months in unopened containers
High gloss >70 at 60 degrees
Gardner Impact, direct & reverse= 100 in. lb. (passed)
No cracks on a 1/8” mandrel
FLEXIBILITY
VISCOSITY
ADHESION
Less than 200 cps (typical)
360 psi @ elcometer (concrete failure, no
delamination) (applied over ARM154X clear
primer
Taber abrasor CS-17 calibrase wheel with 1000
gram total load and 500 cycles= 4.4 mg loss
ABRASION RESISTANCE
PER GALLON
320 to 500 square feet @ 3-5 mils wet thickness
COLORS
CURE SCHEDULE
TACK FREE (Dry to touch)
RECOAT OR TOPCOAT
4-7 hours
9-13 hours
13-24 hours
LIGHT FOOT TRAFFIC
APPLICATION TEMPERATURE
50-90 degrees F with relative humidity
between 60% and 90%
FULL CURE (heavy traffic)
3-5 days
CHEMICAL RESISTANCE
MEK
Methyl Alcohol
Gasoline
10% Sodium Hydroxide
50% Sodium Hydroxide
10% Sulfuric
10% Hydrochloric Acid
Ethylene Glycol
SPECS
Acetic Acid 5%
Xylene
E
B
B
D
E
D
D
D
C
D
Clear (gardner 1)
Recommended ARM154X CLEAR
None recommended
One Component
Product
UV Stable
Super
Durable
Scratch Resistant
Roll On
Application
MIX RATIO
One component product
HARDNESS
2H
POT LIFE (1 gal volume)
3-5 hours
C
Rating Key: Rating key: A - not recommended, B - 2 hour term splash spill, C - 8
hour term splash spill, D - 72 hour immersion, E - long term immersion. NOTE:
extensive chemical resistance information is available through your sales
representative.
DOT CLASSIFICATION
“FLAMMABLE LIQUID N.O.S, 3, UN1993, PGIII”
ArmorPoxy Inc.
1260 North Ave
Plainfield, NJ 07062
armorpoxy.com
E: [e-mail]
P: 888-755-7361