Installation Guide

INSTRUCTIONS
Rev 11/21
NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY
We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our
products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other
than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING
SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE
MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT.
We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of
delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to
make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ
THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.
ArmorPoxy Inc.
1260 North Ave
Plainfield, NJ 07062
armorpoxy.com
E: [e-mail]
P: 888-755-7361
PLEASE READ INSTRUCTIONS THOROUGHLY BEFORE APPLICATION BEGINS. FAILURE TO DO SO
CAN RESULT IN PRODUCT FAILURE.
PRODUCT STORAGE
SURFACE PREPARATION
Store product at normal room temperature before using. Continuous storage should be between 60 and 90 degrees F.
The most suitable surface preparation would be sand blasting, diamond grinder w/30 grit or coarser or acid etching (followed by a thorough rinsing) to remove all
laitance and provide a suitable application profile. All dirt, foreign contaminants, oil and laitance must be removed to assure a trouble free bond to the substrate. A
test should be made to determine that the concrete is dry; this can be done by placing a 4’X4’ plastic sheet on the substrate and taping down the edges. If after 24
hours, the substrate is still dry below the plastic sheet, then the substrate is dry enough to start coating.
ARM707X-CM
100% SOLIDS EPOXY COATING
PRODUCT MIXING
PLEASE ONLY PREPARE QUANTITY THAT MAY BE APPLIED DURING POT LIFE OF MIXTURE. MIX RATIO IS 2A:1B.
In a separate mixing bucket pour both 1 gallons of parts A. Mix using a metal or paddle mixer and a drill for a minimum of 2 minutes. This is important to ensure
an even color consistency in the final coating. Once mixed pour Part B into the mixing bucket and mix both components for at least 3 minutes using a drill at low
revolution (300 to 450 rpm) to reduce trapping of air. If applying to smaller areas that do no require whole 3 gal kit to be used please ensure to only mix what can
be used at the mixing ratio of 2A:1B. Close any containers that are unmixed and store indoors and in cool environment.
PRODUCT APPLICATION
The mixed material can be applied by brush or roller. However, the material can also be applied by a suitable serrated squeegee and then back rolled as long as
the appropriate thickness recommendations are maintained. Maintain temperatures and relative humidity within the recommended ranges during the application
and curing process. If concrete conditions or over aggressive mixing causes air entrapment, then an air release roller tool should be used prior to the coating
tacking off to remove the air entrapped in the coating.
RECOATING OR TOPCOATING
If you opt to recoat or topcoat this product, you must first be sure that the coating has tacked off before recoating. PLEASE REFER TO THE REOCAT WINDOW
STATED IN THE TDS. All previous coats should be deglossed to insure a trouble free bond prior to application of recoats or topcoats. Colder temperatures will
require more cure time for the product before recoating or topcoating can commence. Before recoating or topcoating, check for epoxy blushes (a whitish, greasy
film or deglossing). If a blush is present, it can be removed by any standard detergent cleaner prior to topcoating or recoating. Many epoxy coatings and urethanes
as well as multiple coats of this product are compatible for use as a topcoat. If using a product not sold by Armorpoxy please consult with your sales representative
to ensure product compatibility.
CLEANING
Clean all tools and materials with the cleaner/thinner for epoxies. Wash hands and skin carefully with warm soapy water. Once product has hardened, it may only
be removed through mechanical means.
FLOOR CLEANING
Caution! Some cleaners may affect the color of the floor installed. Test each cleaner in a small area, utilizing your cleaning technique. If no ill effects are noted, you
can continue to clean with the product and process tested.
HEALTH AND SAFETY
In case of skin contact, wash with water and soap. In case of eye contact, immediately rinse with water for at least 15 minutes. Consult with a doctor. For
respiratory problems, transport victim to fresh air. Remove contaminated clothes and clean before reuse. Components A and B contain toxic ingredients.
Prolonged contact of this product with the skin is susceptible to provoke an irritation. Avoid eye contact. Contact with may cause serious bums. Avoid breathing
vapors release from this product. This product is a strong sensitizer. Wear safety glasses and chemical resistant gloves. A breathing apparatus filtering organic
vapors approved by the NIOSH/MSHA is recommended. Predict suitable ventilation.